Effect of Thermal Tempering on Strength and Crack Propagation Behavior of Feldspathic Porcelains

Abstract

The objective of this study was to test the hypothesis that tempering stress can retard the growth of surface cracks in layered porcelain discs with variable levels of contraction mismatch. Porcelain discs, 16 mm in diameter and 2 mm thick, were prepared with a 0.5-mm-thick layer of opaque porcelain (0) and a 1.5-mm-thick layer of body porcelain (B). The materials were selected to produce contraction coefficient differences, ao-aB, of +3.2, +0.7, -0.9, and -1.5 ppm/°C. Body porcelain discs with a thickness of 2 mm were used as the thermally compatible control specimens (Δα=0). The discs were fired to the maturing temperature of body porcelain (982°C) and were then subjected to three cooling procedures: slow cooling (SC) in a furnace, fast cooling (FC) in air, and tempering (T) by blasting the surface of the body porcelain with compressed and dried air for 90 s. The dimensions of cracks induced by a Vickers microhardness indenter under a load of 4.9 N were measured at baseline and six months after indentation at 80 points along diametral lines within the surface of body porcelain. In addition, biaxial flexure tests were performed to determine the influence of mismatch and tempering on flexure strength. The results of ANOVA indicate that crack dimensions were influenced significantly by the interaction of cooling rate and contraction mismatch (p<0.0001). Multiple contrast analysis by the Tukey's HSD Test indicated that the crack lengths of tempered specimens at baseline and six months were significantly smaller (p<0.05) than the corresponding values for the FC and SC specimens. For tempered specimens with contraction differences of + 3.2, 0, and -1.5 ppm/°C, the mean crack lengths during the six-month period increased by 10.8%, 8.3%, and 9.7%, respectively, compared with increases of 13.8%, 20.1%, and 15.9%, respectively, for the SC specimens. Tempering treatment of the compatible discs (Δα=0) resulted in the highest mean flexure-strength value of 116.2 MPa. This value was 2.6 times greater than the corresponding value for the slow-cooled specimens. These results indicate that tempering by forced convective cooling in air significantly strengthened bilayered discs and reduced the initial size of induced surface cracks. However, tempering stress was less effective in reducing the propagation rate of induced cracks.

Get full access to this article

View all access options for this article.

References

Anusavice, K.J. ; Dehoff, P.H. ; Hojjatie, B. ; and Gray, A. (1989): Influence of Tempering and Contraction Mismatch on Crack Development in Ceramic Surfaces, J Dent Res 68 :1182-1187.

Anusavice, K.J. ; Gray, A. ; and Shen, C. (1991): Influence of Initial Flaw Size on Crack Growth in Air-tempered Porcelain, J Dent Res 70:131-136.

Ban, S. and Anusavice, K.J. (1990): Influence of Test Method on Failure Stress of Brittle Dental Materials, J Dent Res 69 :1791-1799.

Creyke, W.E.C. (1968): Delayed Fracture of Glazed Porcelain, Trans Br Ceram Soc 67:339-365.

Dehoff, P.H. and Anusavice, K.J. (1989): Tempering Stresses in Feldspathic Porcelain, J Dent Res 68:134-138.

Doremus, R.H. (1973): Strengthening of Glass. In: Glass Science , R.H. Doremus , Ed., New York: John Wiley & Sons, Inc., pp. 310-315.

Dunn, B. ; Levy, M.N. ; and Reisbick, M.H. (1977): Improving the Fracture Resistance of Dental Ceramic , J Dent Res 56 :1209-1213.

Farah, J.W. and Craig, R.G. (1975): Distribution of Stresses in Porcelain-Fused-to-Metal and Porcelain, J Dent Res 54:255-261.

Gardon, R. (1980): Thermal Tempering of Glass, Vol. 5, Elasticity and Strength in Glasses. In: Glass Science and Technology, D.R. Uhlmann and N.J. Kreidl , Eds., New York: Academic Press, pp. 144-216.

10.

Gupta, P.K. and Jubb, N.J. (1981): Post-Indentation Slow Growth of Radial Cracks in Glasses, JAm Ceram Soc 64:C112-C114.

11.

Jones, D.W. (1983): The Strength and Strengthening Mechanisms of Dental Ceramics. In: Dental Ceramics, Proceedings of the First International Symposium on Ceramics, J.W. McLean, Ed., Chicago: Quintessence Publishing Company, pp. 83-141.

12.

Kase, H.R. and Tesk, J.A. (1985): Elastic Constants of Two Dental Porcelains, J Mater Sci 20:524-531.

13.

Marshall, D.B. (1980): An Improved Biaxial Flexure Test for Ceramics , Ceram Bull 59:551-553.

14.

Marshall, D.B. and Lawn, B.R. (1977): An Indentation Technique for Measuring Stresses in Tempered Glass Surfaces, J Am Ceram Soc 60:86-87.

15.

Marshall, D.B. and Lawn, B.R. (1978a): Measurement of Nonuniform Distribution of Residual Stresses in Tempered Glass Discs, Glass Technology 19:57-58.

16.

Marshall, D.B. and Lawn, B.R. (1978b): Strength Degradation of Thermally Tempered Glass Plates, J Am Ceram Soc 61:21-27.

17.

Marshall, D.B. and Lawn, B.R. (1979): Residual Stress Effects in Sharp Contact Cracking, Part 1. Indentation Fracture Mechanics, J Mater Sci 14:2001-2012.

18.

Wachtman, J.B., Jr. ; Capps, W. ; and Mandel, J. (1972): Biaxial Flexure Test of Ceramic Substrate, J Mater 7:188-194.