Effect of Firing Temperature and Water Exposure on Crack Propagation in Unglazed Porcelain

Abstract

Static fatigue of dental ceramics results from the interaction of residual tensile stress and an aqueous environment. This phenomenon is a potential cause of delayed crack formation and propagation in ceramic or metal-ceramic restorations. For dental ceramics, the influence of microstructural defects such as porosity or fissures caused by incomplete sintering is not known. The objectives of this study were to characterize the influence of porosity (produced by underfiring) on the crack propagation resistance of two feldspathic porcelains and to determine whether lower stress corrosion susceptibility or higher fracture toughness accounts for the superior thermal shock resistance of one of these ceramics.

We underfired bars of each porcelain, 25 mm × 4 mm × 4 mm, by as much as 84°C below their recommended firing temperatures. After polishing the specimens through 0.05 μm alumina, we induced cracks in their surfaces with a Vickers microhardness indenter. Semicircular cracks, which were produced under an applied indenter load of 19.6 N, grew with time during storage in distilled water at 37°C. Underfiring of both ceramics caused a slight increase in fracture toughness and a relatively small change in pore volume fraction until we underfired the ceramics at 30°C or more. The crack propagation data indicate that the higher thermal shock resistance of one of the ceramics-as measured previously by a water-quench technique-may be due to its greater resistance to stress corrosion at the initial stage of crack propagation.

Get full access to this article

View all access options for this article.

References

Anstis, G.R. ; Chantikul, P. ; Lawn, B.R. ; and Marshall, D.B. (1981): A Critical Evaluation of Indentation Techniques for Measuring Fracture Toughness I. Crack Measurements, J Am Ceram Soc 64:533-538.

Anusavice, K.J. ; Ringle, R.D. ; Morse, P.K. ; Fairhurst, C.W. ; and King, G.E. (1981): A Thermal Shock Test for Porcelain-Metal Systems , J Dent Res 60:1686-1691.

Coble, R.L. and Kingery, W.D. (1956): Effect of Porosity on Physical Properties of Siritered Alumina, J Am Ceram Soc 39:377-385.

Dehoff, P.H. ; Anusavice, K.J. ; and Boyce, R.J. (1983): Analysis of Thermally-induced Stresses in Porcelain-Metal Systems, J Dent Res 62:593-597.

Freiman, S.W. (1980): Fracture Mechanics of Glass. In: Glass: Science and Technology, D.R. Uhlmann and N.J. Kreidl , Eds., New York: Academic Press, pp. 27-29.

Gupta, P.K. and Jubb, N.J. (1981): Post-indentation Slow Growth of Radial Cracks in Glasses, J Am Ceram Soc 64:C112-C114.

Jones, D.W. ; Jones, P.A. ; and Wilson, H.J. (1972): The Relationship between Transverse Strength and Testing Methods for Dental Ceramics, J Dent 1:85-91.

Jones, D.W. and Wilson, J.H. (1975): Some Properties of Dental Ceramics, J Oral Rehabil 2:379-396.

Lawn, B.R. ; Evans, A.G. ; and Marshall, D.B. (1980): Elastic/Plastic Indentation Damage in Ceramics: The Median/Radial Crack System, J Am Ceram Soc 63:574-581.

10.

Lawn, B.R. and Fuller, E.R. (1975): Equilibrium Penny-like Cracks in Indcntation Fracture , J Mater Sci 10:2016-2024.

11.

Marshall, D.B. (1983): Controlled Flaws in Ceramics - A Comparison of Knoop and Vickers Indentation, J Am Ceram Soc 66:127-131.

12.

Morena, R. ; Lockwood, P.E. ; Mackert, J.R., Jr. ; and Fairhurst, C.W. , (1984): Fracture Toughness and Crack-Microstructure Interaction of a Dental Porcelain, J Dent Res 63:234, Abst. No. 573.

13.

Nadeau, J.S. and Bennett, R.C. (1978): Some Effects of Dispersed Phases on the Fracture Behavior of Glass. In: Fracture Mechanics of Ceramics, Vol. 4, Proceedings of the International Symposium of Fracture Mechanics, R.C. Brandt , D.P.H. Hasselman , and F.F. Lange , Eds., New York: Plenum Press, pp. 961-972.

14.

Sherrill, C.A. and O'Brien, W.J. (1974): Transverse Strength of Aluminous and Feldspathic Porcelain, J Dent Res 53:683-690.

15.

Soma, T. ; Matsui, M. ; Oda, I. ; and Yamamoto, N. (1980): Applicability of Crack Propagation Data to Failure Prediction in Porcelain, J Am Ceram Soc 63:166-169.

16.

Underwood, E.E. (1973): Applications of Quantitative Mctallography. In: Metals Handbook, Vol. 8, Metallography Structures and Phase Diagrams , T. Lyman , Ed., Metals Park, OH: American Society for Metals, pp. 37-47.

17.

Wiederhorn, S.M. (1969): Fracture Surface Energy of Glass, J Am Ceram Soc 52:99-105.

18.

Wiederhorn, S.M. (1972): A Chemical Interpretation of Static Fatigue, J Am Ceram Soc 55:81-85.