A Numerical Model of Temporomandibular Joint Loading

Abstract

A numerical model of the mandible, its articulating surfaces, and the forces exerted by the primary masticatory muscles has been developed for the purpose of investigating loading of the temporomandibular joint. Evidence is presented which shows that the temporomandibular joint is a load-bearing joint over the normal functional range of bite-force positions and angles. In this investigation, temporomandibular joint loads were found to vary from a maximum appositional force of 60% of the bite force (when bite forces were applied to the incisors) to a distracting force of about 5% of the bite force (when applied to the distal surfaces of the third molars).

TMJ loads tended to reach a minimum as a result of vertically directed bite forces positioned at the second molars. A range of conditions in which bite forces were directed parallel to or within approximately 20° of the mid-sagittal plane was found to be conducive to stability of the temporomandibular joint. This stability included symmetry in the direction and in the magnitude of condylar loads as well as the presence of small forces tending to appose the condyle and articular eminence.

TMJ loads tended to reach a maximum in response to mediolaterally directed bite forces. This result is consistent with the fact that no muscle of mastication exhibits a spatial orientation in which the muscle fibers are predominantly mediolateral in direction.

Get full access to this article

View all access options for this article.

References

Arvikar, R. and Seireg, A. (1975): A Three Dimensional Model for Analysis of the Human Jaw During Mastication, Ann Conf Eng Med and Biol, Proceedings 28:184.

Barbenel, J.C. (1974): The Mechanics of the Temporomandibular Joint - A Theoretical and Electromyographical Study, J Oral Rehab 1:19-27.

Baron, P. and Debussy, T. (1979): A Biomechanical Functional Analysis of the Masticatory Muscles in Man, Arch Oral Biol 24 :547-553.

Brehnan, K. ; Boyd, R.L. ; Laskin, J. ; Gibbs, C.H. ; and Mahan, P. (1981): Direct Measurement of Loads on the Temporomandibular Joint in Macaca arctoides, J Dent Res 60:1820-1824.

Gosen, A.J. (1974): Mandibular Leverage and Occlusion, J Prosthet Dent 31:369-376.

Hohl, T.H. and Tucek, W.H. (1982): Measurement of Condylar Loading Forces by Instrumented Prosthesis in the Baboon, J Maxfac Surg 10:1-7.

Howell, A.H. and Manly, R.S. (1948): An Electronic Strain Gauge for Measuring Oral Forces, J Dent Res 27:705-712.

Hylander, W.L. (1979): An Experimental Analysis of Temporomandibular Joint Reaction Force in Macaques, Am J Phys Anthrop 51:433-456.

Mansour, R.M. and Reynik, R.J. (1975): In vivo Occlusal Forces and Moments: I. Forces Measured in Terminal Hinge Position and Associated Moments, J Dent Res 54:114-120.

10.

Moffett, B. (1966): The Morphogenesis of the Temporomandibular Joint , Am J Ortho 52:410-415.

11.

Møller, E. (1974): Action of the Muscles of Mastication, Front Oral Physiol 1:121-158.

12.

Mongini, F. (1972): Remodelling of the Mandibular Condyle in the Adult and its Relationship to the Condition of the Dental Arches, Acta Anat 82:437-453.

13.

Mongini, F. (1975): Dental Abrasion as a Factor in Remodelling of the Mandibular Condyle, Acta Anat 92:292-300.

14.

Mongini, F. ; Calderdale, P.M. ; and Barberi, G. (1979): Relationship Between Structure and the Stress Pattern in the Human Mandible, J Dent Res 58:2334-2337.

15.

Osborn, J.W. and Baragar, F.A. (1985): Predicted Pattern of Human Muscle Activity During Clenching Derived From a Computer Assisted Model: Symmetrical Bite Forces , J Biomechanics 18:599-612.

16.

Pruim, G.J. ; De Jongh, H.J. ; and Ten Bosch, J.J. (1980): Forces Acting on the Mandible During Bilateral Static Bite at Different Bite Force Levels, J Biomechanics 13:755-763.

17.

Ralph, J.P. and Caputo, A.A. (1975): Analysis of Stress Patterns in the Human Mandible , J Dent Res 54:814-821.

18.

Roydhouse, R.H. (1955): The Temporomandibular Joint: Upward Force of the Condyles on the Cranium, J Am Dent Assoc 50:166-172.

19.

Smith, D.M. (1984): A Numerical Model of Temporomandibular Joint Loading. Unpublished M.S. Thesis, State University of New York at Buffalo, Buffalo, New York.

20.

Smith, R.J. (1978): Mandibular Biomechanics and Temporomandibular Joint Function in Primates, Am J Phys Anthrop 49 :341-350.

21.

Standlee, J.P. ; Caputo, A.A. ; and Ralph, J.P. (1977): Stress Trajectories Within the Mandible Under Occlusal Loads, J Dent Res 56:1297-1302.

22.

Standlee, J.P. ; Caputo, A.A. ; and Ralph, J.P. (1981): The Condyle as a Stress-distributing Component of the Temporomandibular Joint, J Oral Rehab 8:391-400.

23.

Throckmorton, G.S. and Throckmorton, L.S. (1985): Quantitative Calculation of Temporomandibular Joint Reaction Forces - I. The Importance of the Magnitude of the Jaw Muscle Forces, J Biomechanics 18:445-452.

24.

Throckmorton, G.S. (1985): Quantitative Calculations of Temporomandibular Joint Reaction Forces - II. The Importance of the Direction of the Jaw Muscle Forces, J Biomechanics 18 :453-461.

25.

Tradowsky, M. and Kubicek, W.F.III (1981): Method of Determining the Physiologic Equilibrium Point of the Mandible, J Prosthet Dent 45:558-563.

26.

Tradowsky, M. and Dworkin, J.B. (1982): Determination of the Physiologic Equilibrium Point of the Mandible by Electronic Means, J Prosthet Dent 48:89-98.

27.

Wright, D.M. (1968): The Postnatal Development of the Human Temporomandibular Joint. Unpublished M.S. Thesis, University of Washington , Seattle, Washington.