This work investigated the mechanical properties of glass/epoxy laminates reinforced by kaolin powder with graded properties by performing tensile, 3-point bending, impact tests, and compression after impact (CAI) tests. Firstly, we evaluated the effects of mixing parameters on particle dispersion and the effect of kaolin powder rate on the epoxy properties. It was found that the optimal parameters for a good distribution are a temperature of 60°C with 10 min of stirring time and the optimum kaolin powder rate is 5 wt %. Secondly, four graded heterogeneous laminates were elaborated with increased powder rate at each 1, 2, 3, and 4 layers named models 1/1, 2/2, 3/3, and 4/4, respectively. The test results showed that the powder gradient distribution considerably influences the behavior of the composite, with a significant improvement in mechanical properties compared to unreinforced glass/epoxy laminates. The model 1/1 on the top side exhibits the most significant increase in flexural modulus and maximum flexural strength, respectively, compared to the unfilled specimen. The impact tests showed that the powder distribution gradient is essential in absorbing the leading force and energy. The model 1/1 on the top side showed the best impact strength. According to this previous finding, adding ceramic particles in a polymer matrix; with a particular gradient distribution; significantly enhances the composite laminates' properties, especially under bending load. This heterogeneous composite type finds its application in closed structures where the load side is known, such as tanks and aircraft wings, and will allow a considerable weight gain.
BerthelotJMLingFF. Composite materials: mechanical behavior and structural analysis, Vol 435. New York: Springer, 1999.
2.
MortensenASureshS. Fundamentals of functionally graded materials: processing and thermomechanical behaviour of graded metals and metal-ceramic composites. Book. Maney Publishing, 1998.
WangYNiQQZhuY, et al.. Development of functionally graded vapor-grown carbon-fiber/polymer materials. Polym Compos2013; 34(10): 1774–1781.
5.
KiebackBNeubrandARiedelH. Processing techniques for functionally graded materials. Mater Sci Eng A2003; 362(1–2): 81–106.
6.
MiyamotoY. Development of functionally graded materials by HIP. J Soc Mater Sci, Japan 2000; 6: 3–8.
7.
KrumovaMKlingshirnCHaupertF, et al.Microhardness studies on functionally graded polymer composites. Compos Sci Technol2001; 61(4): 557–563.
8.
ButcherRJRousseauCETippurHV. A functionally graded particulate composite: preparation, measurements and failure analysis. Acta Mater1998; 47(1): 259–268.
9.
WangMPorterDBonfieldW. Processing, characterization, and evaluation of hydroxyapatite reinforced polyethylene. Br Ceram Trans1994; 93: 91–95.
10.
PompeWWorchHEppleM, et al.Functionally graded materials for biomedical applications. Mater Sci Eng A2003; 362(1–2): 40–60.
11.
XuedongLChangmingLHaiboX. Fabrication of Al–Si–Mg functionally graded materials tube reinforced with in situ Si/Mg2Si particles by centrifugal casting. Compos B Eng2013; 45(1): 8–21.
12.
BafekrpourESimonGPHabsudaJ, et al.Fabrication and characterization of functionally graded synthetic graphite/phenolic nanocomposites. Mater Sci Eng A2012; 545: 123–131.
13.
TsotraPFriedrichK. Electrical and mechanical properties of functionally graded epoxy-resin/carbon fibre composites. Compos Part A Appl Sci2003; 34(1): 75–82.
14.
PatnaikABhattAD. Mechanical and dry sliding wear characterization of epoxy–TiO2 particulate filled functionally graded composites materials using Taguchi design of experiment. Mater Design2011; 32(2): 615–627.
15.
ChungHDasS. Processing and properties of glass bead particulate-filled functionally graded Nylon-11 composites produced by selective laser sintering. Mater Sci Eng A2006; 437(2): 226–234.
16.
JordanJJacobKITannenbaumR, et al.Experimental trends in polymer nanocomposites - a review. Mater Sci Eng A2005; 393(1–2): 1–11.
17.
WangYNiQQZhuY, et al.. Fabrication of functionally graded nano-TiO2 -reinforced epoxy matrix composites. Polym Compos2014; 35(3): 557–563.
18.
JumahatASoutisCMahmudJ, et al.Compressive properties of nanoclay/epoxy nanocomposites. Procedia Eng2012; 41: 1607–1613.
19.
GilliaOCaillensB. Fabrication of a material with composition gradient for metal/ceramic assembly. Powder Technol2011; 208(2): 355–366.
20.
MishinaHInumaruYKaitokuK. Fabrication of ZrO2/AISI316L functionally graded materials for joint prostheses. Mater Sci Eng A2008; 475(1–2): 141–147.
21.
BouchafaABenzairATounsiA, et al.Analytical modelling of thermal residual stresses in exponential functionally graded material system. Mater Design2010; 31(1): 560–563.
22.
HeZMaJTanGEB. Fabrication and characteristics of alumina–iron functionally graded materials. J Alloys Compd2009; 486(1–2): 815–818.
23.
ZemaniKMayAGilsonL, et al.Numerical investigation of the dynamic behavior of a Ti/TiB functionally graded material using Split Hopkinson Pressure Bar test. J Compos Mater2022; 56(7): 1053–1070.
HashmiSARDwivediUK. SiC dispersed polysulphide epoxy resin based functionally graded material. Polym Compos2009; 30(2): 162–168.
26.
KrumovaMKlingshirnCHaupertF, et al.Microhardness studies on functionally graded polymer composites. Compos Sci Technol2001; 61(4): 557–563.
27.
LeeNJJangJParkM, et al.Characterization of functionally gradient epoxy/carbon fibre composite prepared under centrifugal force. J Mater Sci1997; 32(8): 2013–2020.
28.
TsotraPFriedrichK. Electrical and mechanical properties of functionally graded epoxy-resin/carbon fibre composites. Compos Part A Appl Sci Manuf2003; 34(1): 75–82.
29.
LiuXQWangYSZhuJH. Epoxy resin/polyurethane functionally graded material prepared by microwave irradiation. J Appl Polym Sci2004; 94(3): 994–999.
30.
EstiliMTakagiKKawasakiA. Multiwalled carbon nanotubes as a unique agent to fabricate nanostructure-controlled functionally graded alumina ceramics. Scripta Mater2008; 59(7): 703–705.
31.
KwonHBradburyCRLeparouxM. Fabrication of functionally graded carbon nanotube-reinforced aluminum matrix composite. Adv Eng Mater2011; 13(4): 325–329.
32.
MishraSKShuklaDKPatelRK. Effect of particle morphology on flexural properties of functionally graded epoxy-alumina polymer nanocomposite. Mater Res Express2020; 6(12): 1250i9.
33.
QasimSAGuptaN. Comparison of the dielectric properties of functionally graded material dielectrics and layered dielectrics used for electric stress control. IET Sci Meas Technol2020; 14(4): 471–477.
34.
Karami KhorramabadiM. Theoretical predictions on mechanical properties of functionally graded epoxy/clay nanocomposites. ADMT J2020; 13(1): 31–37.
35.
GalehdariNARyanTJKelkarAD. Three dimensional finite element analysis of functionally graded radiation shielding nanoengineered sandwich composites. Int J Mech Mechatron Eng2017; 11(3): 529–533.
36.
MegahedAAEWMegahedM. Fabrication and characterization of functionally graded nanoclay/glass fiber/epoxy hybrid nanocomposite laminates. Iranian Polym J2017; 26(9): 673–680.
37.
PraveenAPVasudevanRArunTM. Recent developments in investigation on buckling and post buckling responses of laminated composite shells. Polym Compos2017; 39: 1–12.
38.
GangSWLamKYReddyJN. The elastic response of functionally graded cylindrical shells to low-velocity. Int J Impact Eng1999; 22(4): 397–417.
39.
ApetreNASankarBVAmburDR. Low-velocity impact response of sandwich beams with functionally graded core. Int J Solids Struct2006; 43(9): 2479–2496.
40.
KashtalyanMMenshykovaM. Three-dimensional elasticity solution for sandwich panels with a functionally graded core. Compos Struct2009; 87(1): 36–43.
41.
PraveenAPMoheezMAManjunathMM, et al.Evaluation of shear properties of carbon nanotube reinforced functionally graded honeycomb composite materials. AIP Conference Proceedings, AIP Publishing LLC2019; 2057: 020067.
42.
NasimAGThomasJRAjitDK. Three-dimensional finite element analysis of functionally graded radiation shielding. Nano Eng Sandw Compos2017; 11(3): 529–533.
43.
MegahedAAWMegahedM. Fabrication and characterization of functionally graded nanoclay/glass fiber/epoxy hybrid nanocomposite laminates. Iranian Polym J2017; 26: 673–680.
44.
HassarM. Influence des nano-charges de noir de carbone sur le comportement mécanique de matériaux composites: application au blindage électromagnétique. Doctoral dissertation, Université de Technologie de Compiègne, 2013.
El-GalyIMSalehBIAhmedMH. Functionally graded materials classifications and development trends from industrial point of view. SN Appl Sci2019; 1: 1378.
47.
SeoHSongDGJhangKY. Measurement of elastic constants by simultaneously sensing longitudinal and shear waves as an overlapped signal. J Korean Soc Nondestruc Test2016; 36(2): 138–148.
48.
International Standards Organization. ISO 527-4: determination of tensile properties—Part 4: test conditions for isotropic and orthotropic fibre-reinforced plastic composites, 1997.
49.
AstmI. Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating materials, 2007. ASTM D790-07.
50.
SolimanEMSheykaMPTahaMR. Low-velocity impact of thin woven carbon fabric composites incorporating multi-walled carbon nanotubes. Int J Impact Eng2012; 47: 39–47.
51.
AkkermanRWarnetLLVan de VenEC. Impact damage in woven fabric reinforced composites. In: Proceedings of the 10th international conference on textile comp TEXCOMP, Vol. 10, 2000.
52.
CesariVDalReMinakG, et al.Damage and residual strength of laminated carbon-epoxy composite circular plates loaded at the centre. Compos Part A Appl Sci Manuf2007; 38: 1163–1173.
53.
DehkordiMTNosratyHShokriehMM, et al.Low velocity impact properties of intra-ply hybrid composites based on basalt and nylon woven fabrics. Mater Design2010; 31(8): 3835–3844.
54.
SutherlandLSGuedes SoaresCG. Impact characterisation of low fibre-volume glass reinforced polyester circular laminated plates. Int J Impact Eng2005; 31(1): 1–23. Polyester circular laminated plates. Int J Impact Eng 2005;31(1):1–23.
55.
SarasiniFTirillòJValenteM, et al.Hybrid composites based on aramid and basalt woven fabrics: impact damage modes and residual flexural properties. Mater Design2013; 49: 290–302.
56.
SarasiniFTirillòJFerranteL, et al.Drop-weight impact behaviour of woven hybrid basalt-carbon/epoxy composites. Compos Part B Eng2014; 59: 204–220.
57.
TanWFalzonBGChiuLN, et al.Predicting low velocity impact damage and Compression-After-Impact (CAI) behaviour of composite laminates. Compos Part A Appl Sci Manuf2015; 71: 212–226.
58.
ZhangCRaoYLiW. Low-velocity impact behavior of intralayer hybrid composites based on carbon and glass non-crimp fabric. Compos Struct2020; 234: 111713.
59.
LévêqueD. Analyse de la tenue au délaminage des composites stratifiés: identification d'un modèle d'interface interlaminaire (Doctoral dissertation, Cachan, École normale supérieure), 1998.
