The incorporation of ornamental stones residues to a polymer resin to produce artificial stone is an alternative to reducing the environmental impacts of inadequate waste disposal; it also represents a technically viable method. The objective of study was to develop an artificial granitic stone (AGS) using 85% in mass of granite agglutinated by 15% epoxy resin, through a vacuum, vibration and compression process. The artificial stone presented superior properties when compared with the natural granite, it had satisfactory mechanical and physical properties, resistant to temperature oscillations, to impact and wear, therefore suitable for applications for flooring subject to instantaneous tension and high-traffic.
CelikMYSabahE.Geological and technical characterisation of Iscehisar (Afyon-Turkey) marble deposits and the impact of marble waste on environmental pollution. J Environ Manage2008;
87: 106–116.
3.
BaraniKEsmailiH.Production of artificial stone slabs using waste granite and marble stone sludge samples. J Min Environ (Int J Min Environ Issues)2016;
7: 135–141.
4.
OliveiraTRibeiroRPMoreirasTF.Caracterizaçõ de lamas do corte de granitos com vista ao uso em obras geotécnicas. Sci Eng J2016;
25: 51–57.
5.
MontaniC.Marble and stones in the world: XXIV report.
Carrara:
Aldus Casa di Edizioni in Camara, 2013.
6.
AdakNCChhetriSMurmuNC, et al.
Analytical and experimental investigation on magnetorheological behavior of CoFe2O4-rGO-incorporated epoxy fluid composites. Adv Compos Hybrid Mater2019;
2: 266–278.
7.
LiJZhangPHeH, et al.
Enhanced thermal transport properties of epoxy resin thermal interface materials. ES Energy Environ2019;
4: 41–47.
8.
XiePYifanLHouQ, et al.
Tunnelinging-induced negative permittivity in Ni/MnOnanocomposite by a Bio-gel derived strategy. J Mater Chem C2020;
8: 3029–3039.
9.
ChauhanSBhushanRK.Improvement in mechanical performance due to hybridization of carbon fiber/epoxy composite with carbon black. Adv Compos Hybrid Mater2018;
1: 602–611
SilvaFSRibeiroCEGRodriguezRJS.Physical and mechanical characterization of artificial stone with marble calcite waste and epoxy resin. Mater Res2018;
21: 6.
12.
PengLQinS.Mechanical behaviour and microstructure of an artificial stone slab prepared using a SiO2 waste crucible and quartz sand. Constr Build Mater2018;
171: 273–280.
13.
SaramiNMahdavianL.Effect of inorganic compound on artificial stones’ properties. Int J Ind Chem2015;
6: 213–219.
14.
BaramalekiSMahdavianL.Investigation of mechano-chemical properties of the effects of nanoparticles in artificial stone produced. Silicon2019;
11: 1071–1082.
15.
BorsellinoCCalabreseLDi BellaG.Effects of powder concentration and type of resin on the performance of marble composite structures. Constr Build Mater2009;
23: 1915–1921.
16.
RibeiroCEGRodriguezRJSVieiraCMF, et al. Production of synthetic ornamental marble as a marble waste added polyester composite. In: HotzaDNovaes de OliveiraAP (eds) Materials science forum.
Zurich:
Trans Tech Publications, 2014, pp. 341–345.
17.
BragaFSBuzziDCCoutoMCL, et al.
Caracterização ambiental de lamas de beneficiamento de rochas ornamentais. Engenharia Sanitária e Ambiental2010;
15: 237–244.
18.
PereiraDSFilhoNLDVecchiGD.Caracterização físico-química e mecânica do sistema Éster de Silsexquioxano/resina epóxi DGEBA/dietilenotriamina. Rev Mater2005;
10: 317–330.
GomesMLPMCarvalhoEASSobrinhoLN, et al.
Production and characterization of a novel artificial stone using brick residue and quarry dust in epoxy matrix. J Mater Res Technol2018;
7: 492–498.
21.
Brazilian Association of Technical Norms – ABNT. ABNT NBR 15845-2: rocks for cladding. Part 2: determination of bulk density, apparent porosity and water absorption: Test Methods (in Portuguese).
Rio de Janeiro:
ABNT, 2015.
22.
Spanish Association of Standards and Certification. UNE-EN 14617-2-08: test methods part 2: determination of the flexural strength (in Spanish). Madrid: UNE-EN, 2008.
23.
Brazilian Association of Technical Standards – ABNT. ABNT NBR 12042: Inorganic materials – Determination of the resistance to abrasion (in Portuguese). Rio de Janeiro: ABNT, 2012.
24.
da Cunha DemartiniTJRodríguezRJSSilvaFS.Physical and mechanical evaluation of artificial marble produced with dolomitic marble residue processed by diamond-plated bladed gang-saws. J Mater Res Technol2018;
7: 308–313.
25.
LeeD-JShinI-J.Effects of vacuum, mold temperature and cooling rate on mechanical properties of press consolidated glass fiber/PET composite. Compos Part A Appl Sci Manuf2002;
33: 1107–1114.
26.
ChiodiCFRodriguezHP.Guide application of stones in coverings. São Paulo Abirochas2009;
118: 37–41.
27.
Brazilian Association of Technical Standards – ABNT. ABNT NBR 15844: rocks for coating – Requirements for granite (in Portuguese).
Rio de Janeiro:
ABNT, 2015.
28.
CarvalhoEASVilela N deFMonteiroSN, et al.
Novel artificial ornamental stone developed with quarry waste in epoxy composite. Mater Res2018;
21: 7.
29.
KaracaZYılmazNGGoktanRM.Abrasion wear characterization of some selected stone flooring materials with respect to contact load. Constr Build Mater2012;
36: 520–526.
30.
CarvalhoEASMarquesVRRodriguesRJS, et al.
Development of epoxy matrix artificial stone incorporated with sintering residue from steelmaking industry. Mater Res2015;
18: 235–239.
31.
FrazãoEFarjallatJ. Technological characteristics of the main Brasilian silicate rocks used as coating stones. In: International conference of natural stone (eds LG Rosa and ZCG Silva), Lisboa, Portugal, 1995, volume 1, pp. 47–58. Ministry of Trade and Tourism.
32.
RestrepoJJColoradoHA. Additive manufacturing of composites made of epoxy resin with magnetite particles fabricated with the direct ink writing technique. J Compos Mater 2020; 54: 647–657.
