The present study reports on an experimental development addressing 3D void growth in epoxy-based carbon fibre-reinforced composites during their curing process. For that purpose and to investigate autoclave condition effects, composites samples were cured according to different curing cycles by using a specially designed device, which was installed on a synchrotron beamline dedicated to ultra-fast X-ray microtomography. Thus, 3D in situ images of the voids evolution could be obtained as a function of time, temperature, pressure, initial water content and resin conversion degree, which are the driving factors of void size evolution during the polymerization cycles. Results confirm the combined roles of humidity and temperature on the porosity growth and highlight the complex shape of the generated bubbles. It is also emphasized that a sharp increase of the applied pressure during the curing cycle instantaneously reduces the pore size. Such results improve the understanding of the cure of composites parts and can finally be used as input data for modelling purpose or for validation of existing models.
TangJLeeWSpringerG. Effects of cure pressure on resin flow, voids and mechanical properties. J Compos Mater1987; 21: 421–440.
2.
De AlmeidaSNetoZ. Effect of void content on the strength of composite laminates. Compos Struct1994; 28: 139–148.
3.
OlivierPCottuJFerretB. Effects of cure cycle pressure and voids on some mechanical properties of carbon/epoxy laminates. Composites1995; 26: 509–515.
4.
CostaMDe AlmeidaSRezendeM. The influence of porosity on the interlaminar shear strength of carbon/epoxy and carbon/bismaleimide fabric laminates. Compos Sci Technol2001; 61: 2101–2108.
5.
ChambersAEarlJSquiresC, et al.The effect of voids on the flexural fatigue performance of unidirectional carbon fibre composites developed for wind turbine applications. Int J Fatigue2006; 28: 1389–1398.
6.
WisnomMReynoldsTGwilliamN. Reduction in interlaminar shear strength by discrete and distributed voids. Compos Sci Technol1996; 56: 93–101.
7.
CampbellFMallowABrowningC. Porosity in carbon fiber composites-an overview of causes. J Adv Mater1995; 26: 18–33.
8.
MehdikhaniMGorbatikhLVerpoestI, et al.Voids in fiber-reinforced polymer composites: a review on their formation, characteristics, and effects on mechanical performance. J Compos Mater2018; 53: 1579–1669. .
9.
KardosJDudukovicMDaveR. Void growth and resin transport during processing of thermosetting matrix composites. Adv Poly Sci1986; 80: 102–123.
10.
GrunenfelderLKNuttSR. Void formation in composite prepregs – effect of dissolved moisture. Compos Sci Technol2010; 70: 2304–2309.
11.
AgiusKMagniezKB. FoxB. Cure behaviour and void development within rapidly cured out-of-autoclave composites. Compos Part B Eng2013; 47: 230–237.
12.
WoodJBaderM. Void control for polymer matrix composites (1): theoretical and experimental methods for determining the growth and collapse of gas bubbles. Compos Manuf1994; 5: 139–147.
13.
HuangHTalrejaR. Effects of void geometry on elastic properties of unidirectional fiber reinforced composites. Compos Sci Technol2005; 65: 1964–1981.
14.
LiuLZhangBWangD, et al.Effects of cure cycles on void content and mechanical properties of composite laminates. Compos Struct2006; 73: 303–309.
15.
EpsteinPSPlessetMS. On the stability of gas bubbles in liquid-gas solutions. J Chem Phys1950; 18: 1505–1509.
16.
ScrivenLE. On the dynamics of phase growth. Chem Eng Sci1959; 10: 1–13.
17.
KwakHKimY. Homogeneous nucleation and macroscopic growth of gas bubble in organic solutions. Int J Heat Mass Tran1998; 41: 757–767.
18.
Ledru Y. Etude de la porosité dans les matériaux composites stratifiés aéronautiques. PhD Dissertation, Université de Toulouse, France, 2009.
19.
De Parscau du PlessixBLe CorreSJacqueminF, et al.Improved simplified approach for the prediction of porosity growth during the curing of composite parts. Compos Part A2016; 90: 549–558.
20.
LedruYPiquetRMichelL, et al.Quantification 2-d et 3-d de la porosité par analyse d'images dans les matériaux composites stratifiés aéronautiques. Comptes Rendus des JNC 162009.
21.
LittleJYuanXJonesM. Characterisation of voids in fibre reinforced composite materials. NDT & E Int2012; 46: 122–127.
22.
George A and Drechsler K. Void characterization and membrane selection in the vacuum assisted process. In: European conference on composite materials, Venice, Italy, 24-28 June, 2012.
23.
HernandezSSketFMolina-AldareguiaJ, et al.Effect of curing cycle on void distribution and inter-laminar shear strength in polymer-matrix composites. Compos Sci Technol2011; 71: 1331–1341.
24.
HernandezSSketFGonzalezC, et al.Optimization of curing cycle in carbon fiber-reinforced laminates: void distribution and mechanical properties. Compos Sci Technol2013; 85: 73–82.
25.
LeTDumontPOrgéasL, et al.X-ray phase contrast microtomography for the analysis of the fibrous microstructure of SMC composites. Compos Part A2008; 39: 91–103.
26.
CenteaTHubertP. Measuring the impregnation of an out-of-autoclave prepreg by micro-CT. Compos Sci Technol2011; 71: 593–599.
27.
LambertJChambersASinclairI, et al.3D damage characterisation and the role of voids in the fatigue of wind turbine blade materials. Compos Sci Technol2012; 72: 337–343.
28.
SisodiaSMGarceaSCGeorgeAR, et al.High-resolution computed tomography in resin infused woven carbon fibre composites with voids. Compos Sci Technol2016; 131: 12–21.
LatilPOrgéasLGeindreauCDumontP, et al.Towards the 3D in situ characterisation of deformation micro-mechanisms within a compressed bundle of fibres. Compos Sci Technol2011; 71: 480–488.
31.
VilaJSketFWildeF, et al.An in situ investigation of microscopic infusion and void transport during vacuum-assisted infiltration by means of X-ray computed tomography. Compos Sci Technol2015; 119: 12–19.
32.
LarsonNMZokFV. Insights from in-situ X-ray computed tomography during axial impregnation of unidirectional fiber beds. Compos Part A2018; 107: 124–134.
33.
LimodinNSalvoLBollerE, et al.In situ and real-time 3-D microtomography investigation of dendritic solidification in an Al-10wt% Cu alloy. Acta Mater2009; 57: 2300–2310.
34.
De Parscau du PlessixBJacqueminFLefébureP, et al.Characterization and modeling of the polymerization-dependent moisture absorption behaviour of an epoxy-carbon-fiber-reinforced composite material. J Compos Mater2016; 50: 2495–2505.
35.
Ferre SentisDOrgéasLDumontPJJ, et al.3D in situ observations of the compressibility and pore transport in sheet moulding compounds during the early stages of compression moulding. Compos Part A2017; 92: 51–61.
36.
PaganinDMayoSCGureyevTE, et al.Simultaneous phase and amplitude extraction from a single defocused image of a homogeneous object. J Microsc2002; 206: 33–40.
