Sage Journals: Discover world-class research

Abstract

Cured-in-place pipe (CIPP), a popular trenchless technology, has gained wide attention for drinking water, sewerage and storm water pipe rehabilitation because of its ease of installation. Here, the physical and thermal properties of steam-cured PET felt/polyester resin CIPPs were studied. ¹H NMR and GC-MS analysis was performed to identify the unreacted volatile organic compounds in cured CIPPs and results were compared to uncured resin and laboratory cured liner characterizations. Results indicated that organic chemicals in cured CIPP altered the mechanical properties and may be leached out with water. Significantly, lower porosity, density and amount of unreacted volatile organic compounds were much less in the CIPP's inner layer as compared to its outer layer. Water conditioning was conducted to investigate the influence of water on CIPP physical and mechanical properties. No changes were observed for density and porosity for either the CIPP's inner and outer layer; however, the flexural modulus increased slightly due to unreacted organic chemical leaching from the CIPPs.

Keywords

Cured-in-place pipe trenchless volatiles porosity leaching processing

Get full access to this article

View all access options for this article.

References

Harada R, Doherty I, Leffler S, et al. Factors affecting installed cured-in-place pipe liner thickness. North Am Soc Trenchless Technol 2011; Paper D-5-03, pp.1–9.

Ashland. Hetron Q 6405 resin. Safety data sheet. Columbus, OH: Author, 2012.

Bridget

. Environmental implications of cured-in-place pipe rehabilitation technology. J Transp Res Board 2009; 2123: 172–9.

Tabor

Newman

Whelton

. Stormwater chemical contamination caused by cured-in-place pipe (CIPP) infrastructure rehabilitation activities. Environ Sci Technol 2014; 48: 10938–10947.

Rahim K. The success of styrene-free cured-in-place pipe (CIPP) resins. Trenchless Technology, Roadshow, Scotibank Convention Center, ON, n.d.

Moore W. Non-Styrene options for cured in place pipe. NASTT – no dig, Ft. Lauderdale, FL USA: n.d.

Mississipi Textile Corporation. MSDS of CIPP of Indiana installation sites. Mississipi: Author, 2016.

Donaldson BM and Baker AJ. Understanding the environmental implications of cured-in-place pipe rehabilitation technology Virginia Transportation Research Council Standard Title Page – report on federally funded project. Charlottesville, VA, 2008.

Ahmad

Bajahlan

. Leaching of styrene and other aromatic compounds in drinking water from PS bottles. J Environ Sci 2007; 19: 421–426.

10.

Teimouri Sendesi

Conkling

et al.

Worksite chemical air emissions and worker exposure during sanitary sewer and stormwater pipe rehabilitation using cured-in-place-pipe (CIPP). Environ Sci Technol Lett 2017; 4: 325–333.

11.

Ajdari

. Volatile organic compound (VOC) emission during cured-in-place-pipe (CIPP) sewer pipe rehabilitation, New Orleans: University of New Orleans, 2016.

12.

Lee

Springer

. Effects of cure on the mechanical properties of composites. J Compos Mater 1988; 22: 15–29.

13.

Alavi-Soltani

Sabzevari

Koushyar

et al.

Thermal, rheological, and mechanical properties of a polymer composite cured at different isothermal cure temperatures. J Compos Mater 2012; 46: 575–587.

14.

Tang

Lee

Springer

. Effects of cure pressure on resin flow, voids and mechanical properties. J Compos Mater 1987; 21: 421–440.

15.

Olivier

Cottu

Ferret

. Effects of cure cycle pressure and voids on some mechanical properties of carbon/epoxy laminates. Composites 1995; 26: 509–515.

16.

Bowles

Frimpong

. Void effects on the interlaminar shear strength of unidirectional graphite fiber reinforced composites. J Compos Mater 1992; 26: 1487–1509.

17.

Koushyar H. Effects of Variation in Autoclave Pressure, Cure Temperature, and Vacuum-Application Time on the Porosity and Mechanical Properties of a Carbon/Epoxy Composite. Doctoral dissertation, Wichita State University, 2011.

18.

Almeida De

Cerqueira

Leali

. The influence of porosity on the interlaminar shear strength of carbon / epoxy and carbon/bismaleimide fabric laminates. Compos Sci Technol 2001; 61: 2101–2108.

19.

Dong

. Effects of process-induced voids on the properties of fibre reinforced composites. J Mater Sci Technol 2016; 32: 597–604.

20.

Alzraiee

Asce

Bakry

et al.

Destructive analysis-based testing for cured-in-place pipe. J Perform Constr Facil 2015; 29: 1–9.

21.

Eric W. Lining of passageways. U.S. Patent 4,064,211, 1977.

22.

Insituform Technologies I. Impregnated Insitutube® product material safety data sheet. Chesterfield, MO: Author, 2005.

23.

Harrison Street Sewer Line Repair – 2016. Section 33 5500 – Sewer Pipe Lining (Cured-In-Place Pipe). 2016.

24.

Allouche

Alam

Simicevic

et al.

A pilot study for retrospective evaluation of cured-in-place pipe (CIPP) rehabilitation of municipal gravity sewers. Tunn Undergr Sp Technol 2014; 39: 82–93.

25.

Young

. Compacting pressure and cure cycle for processing of thick composite laminates. Compos Sci Technol 1995; 54: 299–306.

26.

Mackenzie

. Measurement of resin pressure in composite laminates during cure, Canada: University of British Columbia, 1993.

27.

Liu

Chen

. A review of void formation and its eﬀects on the mechanical performance of carbon fiber reinforced plastic. Eng Trans 2016; 64: 33–51.

28.

A Rubin

Jerina

. Evaluation of porosity in composite aircraft structures. Mech Compos Mater 1994; 30: 587–600.

29.

National Toxicology Program. Report on carcinogens, 14th ed. United States: Author, 2016.

30.

Noh

Patala

Meijboom

. Catalytic evaluation of dendrimer and reverse microemulsion template Pd and Pt nanoparticles for the selective oxidation of styrene using TBHP. Appl Catal A Gen 2016; 514: 253–266.

31.

AkzoNobel. Product data sheet.pdf 2015:1–3. http://www.polymerpds.akzonobel.com/PolymerChemicalsPDS/showPDF.aspx?pds_id=1296.

32.

Alexander

. Environmental fate and effects of styrene. Crit Rev Environ Sci Technol 1997; 27: 383–410.

33.

Dhoot SN. Sorption and transport of gases and organic vapors in poly (ethylene terephthalate) sorption and transport of gases and organic vapors in poly (ethylene terephthalate). PhD dissertation, The University of Texas at Austin, Austin, TX, USA, 2004.

34.

Chowdhury

Wang

Chiu

et al.

Residual stresses introduced to composite structures due to the cure regime: effect of environment temperature and moisture. J Compos 2016; 2016: 1–13.

Supplementary Material

Please find the following supplemental material available below.

For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.

For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.

0.00 MB

0.97 MB

Evaluation of the physical,chemical,mechanical,and thermal properties of steam-cured PET/polyester cured-in-place pipe

Abstract

Keywords

Get full access to this article

References

Supplementary Material