Microstructures and high-temperature tensile properties of mechanically alloyed and spark plasma-sintered 304SS-CNT composites

Abstract

We fabricated and investigated a 304 stainless steel and carbon nanotube (304SS-CNT) composite with an aim to study its microstructures and high-temperature tensile properties. 304SS powders were mixed with carbon nanotubes using ball milling and consolidated using the spark plasma sintering technique. Tensile specimens made from the consolidated samples of 304SS-CNT were tested in a temperature range from 299 K (26℃) to 773 K (500℃). An induction coil was used for high-temperature tensile tests. The yield strength and the work hardening of the 304SS-CNT sample were found to be higher than those of a sample fabricated from 304SS without carbon nanotubes for all tested temperatures. Microstructure analysis carried out using optical microscopy, scanning electron microscopy, and transmission electron microscopy showed that the 304SS-CNT sample has a microstructure significantly different from the 304SS sample, e.g. reduced grain size and many small cuboidal particles. Composition analysis using energy-dispersive spectroscopy revealed that the cuboidal particles are chromium carbides, and the chromium content is reduced in the 304SS-CNT matrix. Retained carbon nanotubes could not be observed; it is thought that the carbon nanotubes may decompose, induce the reduced grain size and chromium carbides.

Keywords

Carbon nanotube-metal composites 304 stainless steel high-temperature tensile tests spark plasma sintering

Get full access to this article

View all access options for this article.

References

International Atomic Energy Agency. Structural materials for liquid metal cooled fast reactor fuel assemblies-operational behavior (IAEA Nuclear Energy Series No. NF-T-4.3). Vienna: IAEA, 2012.

Sun

Zheng

Wei

et al.

Superior radiation-resistant nanoengineered austenitic 304L stainless steel for applications in extreme radiation environments. Sci Rep 2015; 5: 7801–7801.

Oka

Watanabe

Hashimoto

et al.

Morphology of oxide particles in ODS austenitic stainless steel. J Nucl Mater 2013; 442: 164–168.

Chen

Kushima

et al.

Dispersion of carbon nanotubes in aluminum improves radiation resistance. Nano Energy 2016; 225: 319–327.

Bakshi

Lahiri

Agarwal

. Carbon nanotube reinforced metal matrix composites – a review. Int Mater Rev 2010; 55: 41–64.

Sotoudehnia

Paul

. Dispersion of carbon nanotubes in iron by wet processing for the preparation of iron-carbon nanotube composites. Powder Technol 2014; 258: 1–5.

Kaewsai

Watcharapasorn

Singjai

et al.

Thermal sprayed stainless steel/carbon nanotube composite coatings. Surf Coat Technol 2010; 205: 2104–2112.

Massey

Umanzor

Vasudevamurthy

. Thermal and mechanical properties of mechanically alloyed 304LSS-CNT metal matrix composites. J Comp Mater 2016; 51: 1019–1028.

Igata

Miyahara

Ohno

et al.

Proton irradiation creep of thin foil specimens of type 304 austenitic stainless steel and the thickness effects on their mechanical properties. J Nucl Mater 1984; 122: 354–358.

10.

Codrington

Nguyen

et al.

Induction heating apparatus for high temperature testing of thermo-mechanical properties. Appl Therm Eng 2009; 29: 2783–2789.

11.

ASM Committee. Properties of wrought aluminum and aluminum alloys. In: ASM handbook, vol.2., ASM International, 1990, pp.62–122.

12.

Sakumoto

Nakazato

Matsuzaki

. High-temperature properties of stainless steel for building structures. J Struct Eng 1996; 122: 399–406.

13.

Keller

Tabalaiev

Marnier

et al.

Influence of spark plasma sintering conditions on the sintering and functional properties of an ultra-fine grained 316L stainless steel obtained from ball-milled powder. Mater Sci Eng A 2016; 665: 125–134.

14.

Chen

Imai

Umeda

et al.

Effect of spark-plasma-sintering conditions on tensile properties of aluminum matrix composites reinforced with multiwalled carbon nanotubes. JOM 2017; 69: 669–675.

15.

Lipecka

Andrzejczuk

Lewandowska

et al.

Evaluation of thermal stability of ultrafine grained aluminum matrix composites reinforced with carbon nanotubes. Compos Sci 2011; 71: 1881–1885.

16.

Kim

Lee

. High-temperature deformation behavior of carbon nanotube (CNT)-reinforced aluminum composites and prediction of their high-temperature strength. Composites Part A 2014; 67: 308–315.

17.

Kondoh

Threrujirapapong

Umeda

et al.

High-temperature properties of extruded titanium composites fabricated from carbon nanotubes coated titanium powder by spark plasma sintering and hot extrusion. Compos Sci 2012; 72: 1291–1297.

18.

Sun

Imai

et al.

Powder metallurgy titanium metal matrix composites reinforced with carbon nanotubes and graphite. Composites Part A 2013; 48: 57–66.

19.

Feng

Sui

Cai

. Processing of multi-walled carbon nanotube-reinforced TiNi composites by hot pressed sintering. J Compos Mater 2011; 45: 1553–1557.

20.

Feng

Sui

Cai

et al.

Improving wear resistance of TiNi matrix composites reinforced by carbon nanotubes and in situ TiC. Scri Mater 2011; 64: 824–827.

21.

Cai

Feng

Sui

. Preparation of multi-walled carbon nanotube-reinforced TiNi matrix composites from elemental powders by spark plasma sintering. Rare Metals 2012; 31: 48–50.

22.

Howard

Frazer

Lupinacci

et al.

Investigation of specimen size effects by in-situ microcompression of equal channel angular pressed copper. Mater Sci Eng A 2016; 649: 104–113.

23.

Shin

Fivel

Verdier

et al.

Dislocation-impenetrable precipitate interaction: a discrete dislocation simulation analysis. Philos Magaz 2003; 83: 3691–3704.

24.

Liu

Xiao

Wang

et al.

Elevated temperature tensile properties and thermal expansion of CNT/2009Al composites. Compos Sci 2012; 72: 1826–1833.

25.

Ryu

Jin-Phillipp

et al.

Investigation of the interfacial reaction between multi-walled carbon nanotubes and aluminum. Acta Mater 2006; 54: 5367–5375.

26.

Suh

Bae

. Mechanical properties of Fe-based composites reinforced with multi-walled carbon nanotubes. Mater Sci Eng A 2013; 582: 321–325.

27.

Kumar

Banerjee

Pandel

. Effect on mechanical properties of Fe/MWCNT nanocomposites after vary the weight present of MWCNTs prepared by high energy ball milling. Int J Eng Technol 2017; 5: 230–236.