The surface finish of composite plates made using Resin Transfer Molding of glass/polyester is studied. A surface profilometer is used to measure the surface profile and to record raw data. The objective is to develop an objective method (rather than using human judgment) to differentiate the quality of one surface from another. Initially commonly used current techniques are utilized to assess the quality of the surface finish. These include subjective evaluation through a survey of observations from a group of people; the use of the average amplitude of the signals, frequency analysis, and filtering. For surfaces that have approximate quality, human visual observation can differentiate the quality between the surfaces, but the objective methods (average amplitude, frequency spectrum, and filtering) cannot. A new objective technique is found to be able to distinguish surfaces of approximate quality. This uses the comparison between the parameters of a reference good surface to those of the surface under consideration. A comparative index can be obtained to indicate the degree of similarity between the surface under study and the reference (good) surface.
Hull, D. and Clyne, T.W. (2001). An Introduction to Composite Materials, Cambridge Solid State Science Series, 2nd edn, The University of Cambridge, Cambridge.
2.
Hyer, M.W. (1998). Stress Analysis of Fiber-Reinforced Composite Material, The McGraw-Hill Companies, Inc.
3.
Ferabolia, P. and Masinib, A. (2004). Development of Carbon/Epoxy Structural Components for a High Performance Vehicle, Composites: Part B, 35: 323-330.
4.
Shook, G. (1986). Reinforced Plastics for Commercial Composites Source Book, ASM, Metals Park, OH .
5.
U.S. Department of Agriculture Forest Service ( 1987). Wood Handbook: Wood as an Engineering Material, Agricultural Handbook No. 72, Washington, DC.
6.
Introduction to Composites (1998). Composites Institute, 4th edn, Society of the Plastics Industry, New York, NY.
7.
Rosato, D.V. (1997). Designing with Reinforced Plastics, Hanser/Gardner, Cincinnati, Ohio.
8.
Johnson, C.F. (1990). Resin Transfer Molding, In: Mallick, P.K. and Newman, S. (eds), Composite Materials Technology-Process and Properties , Hanser Publisher, New York.
9.
Thomas, L.R. , Miller, A.K. and Chan, A.L. (2002). Fabrication of Complex High Performance Composite Structures at Low Cost Using VARTM, In: International SAMPE Symposium and Exhibition (Proceedings), Vol. 47 (II), pp. 1317-29.
10.
Advani, S.G. and Sozer, E.M. (2001). Liquid Molding of Thermoset Composites, In: Talreja, R. and Manson, J.-A.E. (eds), Polymer Matrix Composites, pp. 807-44, Elsevier Science Ltd, Amsterdam.
11.
Ascani, L. (1994). Recent Advancements and Technical Needs in Structural Concepts, Fabrication, and Joining Flight-Vehicle Materials, Structures, and Dynamics - Assessment and Future Directions, Vol. 1, pp. 67-171, ASME, New York, USA.
12.
Dutiro, C., Alaka, R.N. and Matthews, F.L. (1997). Factors Controlling Surface Finish in Resin Transfer Molding, SAMPE Journal, 33(5): 19-23.
13.
Seefried, J. (1998). SMC-Außenhautteile in Class-A, In: Proceedings SMC Automotive, Daimler Chrysler Sindelfingen.
14.
Schlesinger, G. (1940). Surface Finish, Machinery, 55: 721.
15.
Schmalz, G. (1929). Uber Glatte und Ebenheit als Physikalisches und Physiologishes Problem, Verein Deatscher Ingenieure, 73: 1441.
16.
Schmalz, G. (1936). Technische Oberflaechenkunde, p. 66 and 269, Springer, Berlin.
17.
Abbott, J. and Firestone, A. (1933). A New Profilograph Measures Roughness of Finely Finished and Ground Surface, Autom. Ind., p. 204.
18.
Sherwood, K.F. and Crookall, J.R. (1967 and 1968). Surface Finish Assessment by an Electrical Capacitance Technique, Proc. Inst. Mech. Eng., 182, Part 3K: 344-349.
19.
Whitehouse, D.J. (1990). Biographical Memoirs of R. E. Reason FRS Mem., Proc. Roy. Soc., 36: 437.
20.
Stedman, M. (1987). Mapping the Performance of Surface Measuring Instruments, Proc. SPIE., 803: 138.
21.
Whitehouse, D.J. (1994). Handbook of Surface Metrology, Inst. Phys. Pub., Bristol and Philadelphia.
22.
Osterhold, M. (1998). Influence of Substrate Structure on the Coating Appearance and the Relevant Characterization Methods , Materialwissenschaft und Werktoffechnik, 29(3): 131-136.
23.
Coulthard, M. (1993). On-line Measurement of Paint Appearance on Car Bodies, Metal Finishing, 91(10): 45.
24.
Gasvik, K.J. (1995). Optical Metrology, John Wiley & Sons Ltd.
25.
Neitzel, M. , Blinzier, M., Edelman , K. and Hoecker, F. (2000). Surface Quality Characterization of Textile-Reinforced Thermoplastics, Polymer Composites, 21(4): 630.
26.
27.
Xu, L. and Lee, L.J. (2004). Effect of Nanoclay on Shrinkage Control of Low Profile Unsaturated Polymer(UP) Resin Cured at Room Temperature, Polymer, 45: 7325-7334.
28.
Mandy Herring, L. (2003). Surface Analysis for the Comparison of Quickstep and Autoclave Surface Finish, School of Engineering and Technology, Deakin University, Australia.
29.
Papoulis, A. and Pillai, S.U. (2002). Probability, Random Variables, and Stochastic Processes, The McGraw-Hill Companies, Inc.
30.
Oppenheim, A.V. and Schafer, R.W. (1975). Digital Signal Processing , Prentice-Hall, Inc.
31.
Lockhart, B.G. and Cheetham, B.M.G. (1989). Basic Digital Signal Processing, Butterworths & Co. Ltd.
32.
Smith, S.W. (1998). The Scientist and Engineer's Guide to Digital Signal Processing, California Technical Publishing.
33.
Hu, S., Ganesan, R. and Hoa, S.V. (2004). Probabilistic Analysis of Surface Finish for Automobile Composite Panels, In: Proceedings of the Fifth Joint Canada-Japan Workshop on Composites, pp. 125-132.
Kay, S.M. (1987). Modern Spectral Estimation: Theory and Application, Prentice Hall, Englewood Cliffs, N.J.
40.
Orfnidis, S.J. (1986). Introduction to Signal Processing, New York, Prentice Hall International, Inc.
41.
PostStack Family Reference Manual (2002). Landmark Graphics Corporation, Houston, USA.
42.
PostStack Family Reference Manual (2002). Landmark Graphics Corporation, pp. 105-106, Houston, USA.
43.
Hu, S., Hoa, S.V. and Ganesan, R. (2006). Evaluation of Surface Finish of Composite Automobile Panel, In: The 21st Annual Technical Conference of the American Society for Composites, The University of Michigan, Dearborn Michigan, 17-20 September.
44.
Zhou, Y. (2000). Introduction to Stochastic Processes, Beijing University of Aeronautics & Astronautics.
45.
Swan, A.R.H. and Sandilands, ( 1995). Introduction to Geological Data Analysis, Blackwell Science Ltd.
46.
PostStack Family Reference Manual (2003). Landmark Graphics Corporation, pp. 362-436, Houston, USA .
47.
Hu, S. (2007). Surface Finish Analysis of Composite Automotive Panels, PhD thesis, Concordia University.
