Fracture Toughness of Phenol Formaldehyde Composites Reinforced with E-spheres

Abstract

A commercial phenol formaldehyde-based resole thermosetting resin supplied by Borden Chemical Australia Pty., was reinforced with ceramic-based fillers (SLG) to increase its fracture toughness. This is the second study of the same series. By testing fracture toughness and viscosity at a range of filler addition levels, the optimal addition of SLG was determined in terms of workability, cost, and performance. The composites obtained were post-cured in a conventional oven as in the previous study. The original contributions of this article include lowering the cost of the composite (35wt% of SLG) by 50% but at the same time the fracture toughness was reduced only by 20% (compared to the neat resin), and increasing the fire resistance of the resins tremendously. It was also found that the values of fracture toughness of the samples in this study were higher than those obtained in the previous study when the percentage by weight of SLG varies from 0 to 35%. The shapes of the plots of fracture toughness against percentage by weight of SLG were also different. The possible reasons for the differences were explained.

Keywords

phenol formaldehyde phenolic resin microwaves envirospheres SLG short bar test viscosity.

Get full access to this article

View all access options for this article.

References

Lampman, S. (2003). Characterization and Failure Analysis of Plastics , ASM International, 27.

Smith, W.F. and Hashemir, J. (2006). Foundations of Material Science and Engineering , 4th edn, pp. 523-525, McGraw-Hill , New York.

Strong, A.B. (2006). Plastics: Materials and Processing, 3rd edn, pp. 182-183, 304-309, 323-333, 620-621, Pearson/ Prentice-Hall, New York.

Clarke, J.L. (ed.) (1996). Structural Design of Polymer Composites, pp. 59-62, 343-345, 357, E & FN Spon, UK.

Barker, L.M. (1979). Fracture Mechanics Applied to Brittle Materials, ASTM, STP 678, American Society for Testing and Materials , pp. 73-82.

Baker, L.M. (1980). Development of the Short Rod Method of Fracture Toughness Measurement, In: Proceedings, Conference on Wear and Fracture Prevention, ASM, Metals Park, Ohio, pp. 163-180.

Baker, L.M. (1981) Short Rod and Short Bar Fracture Toughness Specimen Geometries and Test Methods for Metallic Materials, In: Proceedings, Fracture Mechanics: Thirteenth Conference, ASMT STP 743, pp. 456-475.

Chemwatch (2005). Material Safety Data Sheet for Hexion Cellobond J2027L, 1-14.

Chemwatch ( 2005). Material Safety Data Sheet for Hexion Phencat 15, 1-14.

10.

Askeland, D.R. (1998). The Science and Engineering of Materials, 3rd edn, pp. 163-164, Stanley Thornes, UK.

11.

Wang, H. (2007). Engineering Materials - Study Book 1, University of Southern Queensland, 9.13.

12.

Callister, W.D. (2006). Materials Science and Engineering: An Introduction , 7th edn, pp. 217-219, John Wiley and Sons, Inc., USA.

13.

Munz, D. (1981). Determination of Fracture Toughness of High Strength Aluminum Alloys with Cheron Notched Short Rod and Short Bar Specimens, Engineering Fracture Mechanics, 15(1-2): 231-236.

14.

Ku, H. , Trada, M. , Cardona, F. , Rogers, D. and Jacobson, W. (2009), Tensile Tests of Phenol Formaldehyde SLG Reinforced Composites Post-cured in Microwaves: Preliminary Results, Journal of Composite Materials, 2008 (accepted for publication).

15.

Shackelford, J.F. (1992). Introduction to Materials Science for Engineers, 3rd edn, p. 515, Macmillan, New York.

16.

Aierbe, G.A. , Echeverria, J.M. , Riccardi, C.C. and Mondragon , I. (2002). Influence of the Temperature on the Formation of a Phenol Resol Resin Catalyzed with Amine, Polymer No. 43, pp. 2239-2243.

17.

Ku, H. , Rogers, D. , Davey, R. , Cardona, F. and Trada, M. (2008). Fracture Toughness of Phenol Formaldehyde Composites: Pilot Study, Journal of Materials Engineering and Performance , 17(1): 85-90.

18.

Cardona, F. , Rogers, D. , Ku, H. , Pattarachaiyakoop , N. and Trada, M. (2007). Fracture Toughness of Phenol Formaldehyde Composites Reinforced with E-spheres cured in Microwaves, Journal of Electromagnetic Waves and Applications, 21(14): 2137-2146.

19.

Redjel, B. (1995). Mechanical Properties and Fracture Toughness of Phenolic Resin, Plastics, Rubber and Composites Processing and Applications, 24: 221-228.