Epoxy composites with mineral silica containing 0—60 vol% were prepared using a mechanical stirrer. Ethanol at 10wt% was used as the diluent in the epoxy system. The mechanical properties of epoxy composites were studied through flexural and single etch notch tensile mode (SEN-T) fracture toughness tests. Scanning electron microscopy (SEM) was used to assess the flexural fracture surface morphology. The thermal properties were characterized using a dilatometer, dynamic mechanical analyzer (DMA), and thermogravimetric analysis (TGA). In general, it is found that the properties of epoxy composites are governed by the filler loading and the addition of ethanol as the diluent. The addition of the diluent in epoxy permits higher amount of filler content in the epoxy composites system, i.e., 60vol%, compared to that of the non-diluent system at 40vol%. In short, higher filler loading present in a diluent system results in higher stiffness and low coefficient of thermal expansion (CTE) as required in the electronic packaging application.
Lin, L.L. , Ho, T.H. and Wang, C.S. (1997). Synthesis of Novel Trifunctional Epoxy Resins and their Modification With Polydimethylsiloxane for Electronic Application, Polymer, 38(8): 1997—2003.
2.
Li, Y. and Wong, C.P. (2006). Recent Advances of Conductive Adhesives as a Lead-free Alternative in Electronic Packaging: Materials, Processing, Reliability and Applications, Materials Science and Engineering: R: Reports , 51(3): 1—35.
3.
Sun, Y., Zhang, Z. and Wong, C.P. (2005). Influence of Interphase and Moisture on the Dielectric Spectroscopy of Epoxy/Silica Composites, Polymer, 46(7): 2297—2305.
4.
Kang, S., Hong, S.I., Choe, C.R., Park, M., Rim, S. and Kim, J. (2001). Preparation and Characterization of Epoxy Composites Filled with Functionalized Nanosilica Particles Obtained Via Sol—Gel Process, Polymer, 42(3): 879—887.
5.
Kuo, D.H. , Chang, C.C., Su , T.Y., Wang, W.K. and Lin , B.Y. (2004). Dielectric Properties of Three Ceramic/Epoxy Composites, Materials Chemistry andPhysics, 85(1): 201—206.
6.
Raj, P.M., Shinotani, K., Mancheol, S., Bhattacharya, S., Sundaram, V., Zama, S., Jicun, L., Zweben, C., White, G.E. and Tummala, R.R. (2001). Selection and Evaluation of Materials for Future System-on-Package (SOP) Substrate, Proceedings of 51st Electronic Components and Technology Conference, May 29—June 1, pp. 1193—1197.
7.
Tay, H.L. and Cui, C.Q. (1998). Underfill Material Requirements for Reliable Flip Chip Assemblies, Proceedings of 2nd Electronics Packaging Technology Conference, Dec. 8—10, pp. 345—348.
8.
Pourabas, B. and Raeesi, V. (2005). Preparation of ABS/Montmorillonite Nanocomposite Using a Solvent/Non-Solvent Method, Polymer , 46(15): 5533—5540.
9.
Ollevier, T. and Lavie-Compin , G. (2002). An Efficient Method for the Ring Opening of Epoxides With Aromatic Amines Catalyzed by Bismuth Trichloride , Tetrahedron Letters,43(44): 7891—7893.
10.
Shechter, L. , Wynstra, J. and Kurbjy, R.P. (1956). Glycidyl Ether Reactions with Amines, Industrial and Engineering Chemistry, 48: 94—97.
11.
Plazek, D.J. , Seoul, C. and Bero, C.A. (1991). Diluent Effects on Viscoelastic Behavior, Journal of Non-Crystalline Solids,131: 570—578.
12.
Raghavan, D. , Balakrishnan, S. and Gebrekristios , Y. (2003). Optimizing Processing Conditions to Influence the Morphology Of Nanocomposite , Technical Proceedings of the 2003 Nanotechnology Conference and Trade Show, Feb 23—27, pp. 243—245.
13.
Lisardo, N.N.E. , Villanueva, M. and Rial, L.F. (2004). Modification of a Two-component System by Introducing an Epoxy-reactive Diluent: Construction of a Time—Temperature— Transformation (TTT) Diagram, Journal of AppliedPolymer Science , 92: 1190—1198.
14.
Teh, P.L., Jaafar, M., Akil, H.M., Seetharamu, K.N., Wagiman, A.N.R. and Beh, K.S. (2005). Thermal Expansion and Flexural Properties of Particulate Fillers Filled Epoxy Composites, Proceedings of 5th National Symposium of Polymer Materials, Aug. 23—24, Bangi, Malaysia.
15.
Ballard, R.L. , Sailer, R.A., Larson , B. and Soucek, M.D. (2001). Fracture Toughness of Inorganic—Organic Hybrid Coatings, Journal of Coatings Technology,73(913): 107—114.
16.
Kornmann, X. , Rees, M., Thomann, Y., Necola, A., Barbezat, M. and Thomann, R. (2005). Epoxy-layered Silicate Nanocomposites as Matrix in Glass Fibre-Reinforced Composites, CompositesScience and Technology, 65(14): 2259—2268.
17.
Wang, H., Han, W., Tian, H. and Wang, Y. (2005). The Preparation and Properties of Glass Powder Reinforced Epoxy Resin, Materials Letters,59(1): 94—99.
18.
Lee, S.M. (1989). Reference Book For Composites Technology, Volume 1, New York: CRC Press.
19.
Kinloch, A.J. and Young, R.J. (1983). Fracture Behavior of Polymers, London: Elsevier Applied Science Publishers.
20.
Hiroaki, M., Manjusri, M., Lawrence, T.D. and Amar, K.M. (2005). Fracture Toughness and Impact Strength of Anhydride-cured Biobased Epoxy, Polymer Engineering and Science, 45(4): 487.
21.
Gam, K.T. , Miyamoto, M., Nishimura , R. and Sue , H.J. (2003). Fracture Behavior of Core-shell Rubber-modified Clay-epoxy Nanocomposites , Polymer Engineering and Science, 43(10): 1635—1645.
22.
Plangsangmas, L., Mecholsky, J.J. and Brennan, A.B. (1999). Determination of Fracture Toughness of Epoxy Using Fractography, Journal of AppliedPolymer Science, 72(2): 257—268.
23.
Arends, C.B. (1996). Polymer Toughening, New York : Marcel Dekker.
24.
Kumbhat, N., Markondeya Raj, P., Pucha, R.V., Sundaram, V., Doraiswami, R., Bhattacharya, S., Hayes, S., Atmur, S., Sitaraman, S.K. and Tummala, R.R. (2004). Next Generation of Package/Board Materials Technology for Ultra-high Density Wiring and Fine-Pitch Reliable Interconnection Assembly , Proceedings of 54th Electronic Components and Technology, June 1—4, pp. 1843—1850.
25.
Wilkinson, W.N. and Ryan, A.J. (1998). Polymer Processing and Structure Development, London: Kluwer Academic Publishers.
26.
Grohens, Y. , George, B., Touyeras , F., Vebrel, J. and Laude, B. (1997). Experimental Design as a Route for Improving the Performances of Formulated Epoxy Adhesives, Polymer Testing,16(5): 417—427.
27.
Powell, D.O. and Trivedi, A.K. (1993). Flip-chip on FR-4 Integrated Circuit Packaging , Proceedings of 43rd Electronic Components and Technology Conference, June 1—4, pp. 182—186, Orlando, FL, USA.
28.
Konarski, M.M. , Effects of Tg and CTE on Semiconductor Encapsulants , http://www.loctite.pl/int_henkel/loctite/binarydata/pdf/elec_Effects_of_Tg_and_CTE_n_Semiconductor_Encapsulants.pdf, (1998).
29.
Dewprashad, B. and Eisenbraun, E.J. (1994). Fundamentals of Epoxy Formulation, Journal ofChemical Education, 71(4): 290.
30.
Huang, M.T. and Ishida, H. (1999). Dynamic Mechanical Analysis of Reactive Diluent Modified Benzoxazine-based Phenolic Resin, Polymers and PolymerComposites, 7(4): 233—247.
