Numerical Simulation and Experimental Study on Consolidation of Toughened Epoxy Resin Composite Laminates

Abstract

Toughened epoxy resin is one of the most important matrices in composite structural materials. In this article a one-dimensional resin flow/fiber compaction model was used for analysis of the consolidation of a toughened epoxy resin 5228/T700S carbon fiber laminates. The laminate thickness and the fiber volume fraction distribution of cured laminates under different cure cycles were investigated both from the experimental measurements and from the numerical simulation. The calculated and experimental results are in good agreement for all the studied cases. A significantly uneven degree of consolidation along the laminate thickness direction is observed, and it is difficult to improve by altering cure cycle. These results are valuable for the study of the performance of composite parts, provided that uneven distribution of fibers does affect some properties of composite materials.

Keywords

composite laminate numerical analysis consolidation epoxy resin

Get full access to this article

View all access options for this article.

References

Kinsey, S.P. , Haji-Sheikh, A. and Lou, D.Y.S. (1997). A Thermal Model for Cure of Thermoset Composites , J. Mater. Proc. Technol., 63(1): 442–449 .

Loos, A.C. and Springer, G.S. (1983). Curing of Epoxy Matrix Composites , J. Comp. Mater., 17(2): 135–169 .

Gutowski, T.G. , Morigaki, T. and Cai, Z. (1987). The Consolidation of Laminate Composites , J. Comp. Mater., 21(2): 172–188 .

Dave, R. , Kardos, J.L. and Dudukovic M.P. (1987). A Model for Resin Flow during Composite Processing: Part 1–General Mathematical Development , Polym. Comp., 8(1): 29–38 .

Dave, R. (1990). A Unified Approach to Modeling Resin Flow during Composite Processing , J. Comp. Mater., 24(1): 22–41 .

Kardos, J.L. , Dudukovic, J.P. , Mckague, E.L. and Lehman, M.W. (1983). Void Formation and Transport during Composite Laminate Processing, In: Browning, C.E. (ed.), Composite Materials, Quality Assurance and Processing, ASTM STP 797, pp. 96–109.

Gregory, D.S. and Anoush, P. (1993). A Comparison of Two Resin Flow Models for Laminate Processing , J. Comp. Mater., 27(17): 1695–1711 .

Young, W.B. (1995). Compacting Pressure and Cure Cycle for Processing of Thick Composite Laminates , Comp. Sci. Technol., 54(3): 299–306 .

Young, W.B. (1995). Resin Flow Analysis in the Consolidation of Multi-directional Laminated Composites , Polym. Comp., 16(3): 250–257 .

10.

Young, W.B. (1996). Consolidation and Cure Simulations for Laminated Composites , Polym. Comp., 17(1): 142–148 .

11.

Costa, V.A.F. and Sousa, A.C.M. (2003). Modeling of Flow and Thermo-kinetics during the Cure of Thick Laminated Composites , International Journal of Thermal Sciences, 42: 15–22 .

12.

Li, M. and Tucker III, C.L. (2002). Modeling and Simulation of Two-dimensional Consolidation for Thermoset Matrix Composites , Comp. Part A-Appl. S, 33(6): 877–892 .

13.

Pascal, H. , Reza, V. and Anoush, P. (1999). A Two-dimensional Flow Model for the Process Simulation of Complex Shape Composite Laminates , Int. J. Numer. Meth. Engng., 44(1): 1–26 .

14.

Shin, D.D. and Hahn, H.T. (2004). Compaction of Thick Composites: Simulation and Experiment , Polym. Comp., 25(1): 49–59 .

15.

Tredoux, L. and Westhuizen, J. van der (1995). Development of a Numerical Code that Simulates Combined Heat Transfer, Resin Flow and Compaction during Composites Processing , Comp. Manuf., 6(2): 85–92 .

16.

Pascal, H. and Anoush, P. (2001). Aspects of the Compaction of Composite Angle Laminates: An Experimental Investigation , J. Comp. Mater., 35(1): 2–26 .

17.

Ciriscioli, P.R. , Wang, Q. and Springer, G.S. (1992). Autoclave Curing Comparisons of Model and Test Results , J. Comp. Mater., 26(1): 90–102 .

18.

Gutowski, T.G. , Cai, Z. , Bauer, S. , Boucher, D. , Kingery, J. and Wineman, S. (1987). Consolidation Experiments for Laminate Composites , J. Comp. Mater., 21(7): 650–669 .

19.

Wang, K. , Zhang, Z. , Zhamu, A , Gu, Y. and Yang, Y. (2005). A Fiber Optical Microbend Sensor Used for On-line Monitoring in Autoclave Process , Acta Materiae Compositae Sinica, 22(2): 67–70 .

20.

Cai, Z. and Gutowski, T.G. (1992). The 3-D Deformation Behavior of a Lubricated Fiber Bundle , J. Comp. Mater., 26(8): 1207–1237 .

21.

Roller, M.B. (1986). Rheology of Curing Thermosets: A Review , Polym. Eng. Sci., 26(6): 432–440 .

22.

Parnas, R.S. , Flynn, K.M. and Dal-Favero, M.E. (1997). A Permeability Database for Composites Manufacturing , Polym. Comp., 18(5): 623–633 .

23.

Yang, T. , Zhamu, A. , Zhang, Z. and Sun, Z. (2003). BH315-3D Temperature Field Collection System Used in Press Molding Process of Thermosetting Resin Matrix Composites , FRP/CM, 3: 27–33 .

24.

Lee, W.I. , Loos, A.C. and Springer, G.S. (1982). Heat of Reaction, Degree of Cure, and Viscosity of Hercules 3501-6 Resin , J. Comp. Mater., 16(6): 510–520 .

25.

Dusi, M.R. , Lee, W.I. , Ciriscioli, P.R. and Springer, G.S. (1987). Cure Kinetics and Viscosity of Fiberite 976 Resin , J. Comp. Mater., 21(3): 243–261 .

26.

He, P. , Liu, J. , Dai, Y. and Zheng, B. (2000). Influence of Uneven Distribution of the Fibers in the Matrix on the Transverse Tensile Strength , Materials for Mechanical Engineering, 24(1): 8–10 .