A discrete cohesive zone model (DCZM) is implemented to simulate the mode I fracture of two dimensional triaxially braided carbon (2DTBC) fiber composites. The 2DTBC is modeled as an elastic-one-parameter (a66) plastic continuum. The plastic behavior of the 2DTBC was characterized by measuring a66. Mode I fracture tests are carried out by using a modified single edge notch bend (SENB) configuration. Fracture toughness (GIC) as a function of crack extension is measured by a compliance approach. The fracture tests are then simulated by using the DCZM based interface element in conjunction with the commercial software ABAQUS® through a user subroutine UEL. The simulated results, carried out under conditions of plane stress, are compared with the experimental results and also verified for mesh sensitivity. The results presented provide guidelines and a basic understanding to model structural response of non-homogeneous materials, incorporating fracture as a damage mechanism and using constituent level material properties, geometry, and fracture toughness (GIC) as input.
Chou, T.W. (1992). Microstructural Design of Fiber Composites, Cambridge University Press, Cambridge .
2.
Poe, C.C. , Dexter, H.B. and Raju, I.S. (1999). Review of the NAsSA Textile Composites Research , Journal of Aircraft, 36(5): 876-884 .
3.
Ramani, K. and Dai, H.M. (2002). Design and Process for Preformed Woven, Knitted, and Braided Thermoplastic Composite Reinforced Arrester , Journal of Composite Materials, 36(20): 2357-2372 .
4.
Huang, Z.M. (2002). Modeling and Characterization of Bending Strength of Braided Fabric Reinforced Laminates , Journal of Composite Materials, 36(22): 2537-2566 .
5.
Naik, R.A. , Ifju, P.G. and Masters, J.E. (1994). Effect of Fiber Architecture Parameters on Deformation Fields and Elastic-moduli of 2D Braided Composites , Journal of Composite Materials, 28(7): 656-681 .
6.
Naik, N.K. and Sekher, Y.C. (2000). Damage in Woven-fabric Composites Subjected to Low-velocity Impact , Composites Science and Technology, 60(5): 731-744 .
7.
Tang, X.D. and Whitcomb, J.D. (2003). Progressive Failure Behaviors of 2D Woven Composites , Journal of Composite Materials, 37(14): 1239-1259 .
8.
Quek, S.C. , Waas, A.M. , Shahwan, K.W. and Agaram, V. (2003). Analysis of 2D Triaxial Flat Braided Textile Composites , International Journal of Mechanical Sciences, 45(6-7): 1077-1096 .
9.
Song, S.J. and Waas, A.M. (2004). Response and Stability of Woven Composites Under Compressive Loads, ICCES'04, Portugal, July 2004.
10.
Glaessgen, E.H. , Pastore, C.M. , Griffin, O.H. and Birger, A. (1996). Geometrical and Finite Element Modeling of Textile Composites , Composites: Part B.27(1): 43-50 .
11.
Quek, S.C. , Waas, A.M. , Shahwan, K.W. and Agaram, V. (2004). Compressive Response and Failure of Braided Textile Composites: Part 1-Experiments , International Journal of Non-Linear Mechanics, 39: 635-648 .
12.
Quek, S.C. , Waas, A.M. , Shahwan, K.W. and Agaram, V. (2004). Compressive Response and Failure of Braided Textile Composites: Part 2-Computations , International Journal of Non-Linear Mechanics, 39(4): 649-663 .
13.
Sankar, B.V. and Marrey, R.V. (1997). Analytical Method for Micromechanics of Textile Composites , Composites Science and Technology, 57(6): 703-713 .
14.
Woo, K. and Whitcomb, J.D. (1996). Three-dimensional Failure Analysis of Plain Weave Textile Composites Using a Global/Local Finite Element Method , Journal of Composite Materials, 30(9): 984-1003 .
15.
Quek, S.C. , Waas, A.M. , Hoffman, J. and Agaram, V. (2001). The Crushing Response of Braided and CSM Glass Reinforced Composite Tubes , Composite Structures, 52(1): 103-112 .
16.
Rybicki, E.F. and Kanninen, M.F. (1977). Finite-element Calculation of Stress Intensity Factors by a Modified Crack Closure Integral , Engineering Fracture Mechanics, 9(4): 931-938 .
17.
Kutlu, Z. and Chang, F.K. (1992). Modeling Compressive Failure of Laminated Composites Containing Multiple Through-the-width Cracks , Journal of Composite Materials, 26(3): 350-387 .
18.
Tsai, J.L. , Guo, C. and Sun, C.T. (2001). Dynamic Crack Fracture Toughness in Unidirectional Polymeric Composites , Composites Science and Technology, 61(1): 87-94 .
19.
Xie, D. and Biggers, Jr., S.B.Progressive Crack Growth Analysis Using Interface Element Based on the Virtual Crack Closure Technique, Finite Elements in Analysis and Design (in press).
20.
Xie, D. , Waas, A.M. , Shahwan, K.W. , Schroeder, J.A. and Boeman, R.G. (2004). Computation of Energy Release Rates for Kinking Cracks based on Virtual Crack Closure Technique , CMES: Computer Modeling in Engineering & Sciences, 6(6): 515-524 .
21.
Salvi, A.G. , Chung, J. , Waas, A.M. and Caliskan, A. (2003). Strain-rate Effects on Unidirectional Carbon-fiber Composites , AIAA Journal, 41(10): 2020-2028 .
22.
Salvi, Amit , Waas, Anthony, M. and Caliskan, Ari (2003). Fracture of 2D Triaxially Braided Carbon Fiber Composites , In: Proceedings of the American Society for Composites 18th Technical Conference, Gainesville, Florida.
23.
Ungsuwarungsri, T. and Knauss, W.G. (1987). The Role of Damage-softened Material Behavior in the Fracture of Composites and Adhesives, International Journal of Fracture, 35(3): 221-241, See also PhD Thesis, 1985, Aeronautics Department, Caltech, Pasadena, CA.
24.
Xu, X.P. and Needleman, A. (1994). Numerical Simulation of Fast Crack Growth in Brittle Solids , Journal of the Mechanics and Physics of Solids, 42(9): 1397-1434 .
25.
Mi, Y. , Crisfield, M.A. , Davis, G.A.O. and Helweg, H.B. (1998). Progressive Delamination using Interface Elements , Journal of Composites, 32(14): 1246-1272 .
26.
de Borst, R. (2003). Numerical Aspect of Cohesive Zone Models , Engineering Fracture Mechanics, 70(14): 1943-1961 .
27.
Yang, Q.D. and Thouless, M.D. (2001). Mixed-mode Fracture Analyses of Plasticallydeforming Adhesive Joints , International Journal of Fracture, 110(2): 175-187 .
28.
Yang, Q.D. , Thouless, M.D. and Ward, S.M. (1999). Numerical Simulations of Adhesivelybonded Beams Failing with Extensive Plastic Deformation , Journal of the Mechanics and Physics of Solids, 47(6): 1337-1353 .
29.
El-Sayed, S. and Sridharan, S. (2002). Performance of Cohesive Layer Model in the Prediction of Interfacial Crack Growth in Sandwich Beams , Journal of Sandwich Structures and Materials, 4(1): 31-48 .
30.
Li, S. , Thouless, M.D. , Waas, A.M. , Schroeder, J.A. and Zavattieri, P.D. (2005). Mode-I Cohesive-zone Models for Fracture of an Adhesively Bonded Polymer-Matrix Composite , Composites Science and Technology, 65(2): 281-293 .
31.
Li, S. , Thouless, M.D. , Waas, A.M. , Schroeder, J.A. and Zavattieri, P.D. (2005). Use of Cohesive-zone Models to Analyze Fracture of a Fiber-reinforced Polymer-matrix Composite , Composites Science and Technology, 65(3-4): 537-549 .
32.
Zavattieri, P.D. , Raghuram, P.V. and Espinosa, H.D. (2001). A Computational Model of Ceramic Microstructures Subjected to Multi-axial Dynamic Loading , Journal of the Mechanics and Physics of Solids, 49(1): 27-68 .
33.
Espinosa, H.D. , Zavattieri, P.D. and Dwivedi, S.K. (1998). A Finite Deformation Continuum Discrete Model for the Description of Fragmentation and Damage in Brittle Materials , Journal of the Mechanics and Physics of Solids, 46(10): 1909-1942 .
34.
El-Sayed, S. and Sridharan, S. (2002). Cohesive Models for Predicting Delamination Growth and Crack Kinking in Sandwich Structures , International Journal of Fracture, 117(1): 63-84 .
35.
Camacho, G.T. and Ortiz, M. (1996). Computational Modeling of Impact Damage in Brittle Materials , International Journal of Solids and Structures, 33(20-22): 2899-2938 .
36.
Zou, Z. , Reid, S.R. and Li, S. (2003). A Continuum Damage Model for Delaminations in Laminated Composites , Journal of the Mechanics and Physics of Solids, 51(2): 333-356 .
37.
Zhou, F. and Molinari, J.F. (2004). Dynamic Crack Propagation with Cohesive Elements: A Methodology to Address Mesh Dependency , International Journal for Numerical Methods in Engineering, 59(1): 1-24 .
38.
El-Sayed, S. and Sridharan, S. (2001). Predicting and Tracking Interlaminar Crack Growth in Composites using a Cohesive Layer Model , Composites Part B-Engineering, 32(6): 545-553 .
39.
Reedy, E.D. , Mello, F.J. and Guess, T.R. (1997). Modeling the Initiation and Growth of Delaminations in Composite Structures , Journal of Composite Materials, 31(8): 812-831 .
40.
Tvergaard, V. and Hutchinson, J.W. (1992). The Relation Between Crack Growth Resistance and Fracture Parameters in Elastic-plastic Solids , Journal of the Mechanics and Physics of Solids, 40(6): 1377-1397 .
41.
de Borst, R. (2001). Some Recent Issues in Computational Failure Mechanics , International Journal for Numerical Methods in Engineering, 52(1-2): 63-95 .
42.
de Borst, R. (2003). Numerical Aspects of Cohesive-zone Models , Engineering Fracture Mechanics, 70(14): 1743-1757 .
43.
Schellekens, J.C.J. and de Borst, R. (1993). On the Numerical Integration of Interface Elements , International Journal for Numerical Methods in Engineering, 36(1): 43-66 .
44.
Song, S.J. and Waas, A.M. (1995). Energy-based Mechanical Model for Mixed-mode Failure of Laminated Composites , AIAA J., 33(4): 739-745 .
45.
Song, S.J. and Waas, A.M. (1994). Mode-I Failure of Laminated Polymeric Composites , Engineering Fracture Mechanics, 49(1): 17-27 .
46.
Song, S.J. and Waas, A.M. (1994). A Spring Foundation Model for Mode-I Failure of Laminated Composites based on an Energy Criterion , Journal of Engineering Materials and Technology, 116(4): 512-516 .
47.
Song, S.J. and Waas, A.M. (1993). A Nonlinear Elastic-foundation Model for Interlaminar Fracture of Laminated Composites , Composites Engineering, 3(10): 945-959 .
48.
Shahwan, K.W. and Waas, A.M. (1997). Non-self-similar Decohesion along a Finite Interface of Unilaterally Constrained Delaminations, Proceedings of the Royal Society of London . Series A: Mathematical and Physical Sciences, 453(1958): 515-550 .
49.
Pietruszczak, S. and Mroz, Z. (1981). Finite Element Analysis of Deformation of Strain Softening Materials , International Journal for Numerical Methods in Engineering, 17(3): 327-334 .
50.
Pandolfi, A. , Krysl, P. and Ortiz, M. (1999). Finite Element Simulation of Ring Expansion and Fragmentation: The Capturing of Length and Time Scales through Cohesive Models of Fracture , International Journal of Fracture, 95(1-4): 279-297 .
51.
de Borst, R. , Guitierrez, M.A. , Wells, G.N. , Remmers, J.J.C. and Askes, H. (2004). Cohesive-zone Models, Higher-order Continuum Theories and Reliability Methods for Computational Failure Analysis , International Journal for Numerical Methods in Engineering, 60(1): 289-315 .
52.
Bazant, Z.P. and Oh, B.H. (1984). Rock Fracture via Strain-softening Finite-elements , Journal of Engineering Mechanics-ASCE, 110(7): 1015-1035 .
53.
Garikiapati, K. (2002). A Variational Multiscale Method to Embed Micromechanical Surface Laws in the Macromechanical Continuum , CMES-Computer Modeling in Engineering & Sciences, 3(2): 175-184 .
54.
Xie, D. and Waas, A.M. (2005). Mixed Mode Fracture Modeling using a Discrete Cohesive Zone Model, CMES: Computer Modeling in Engineering & Sciences (in press).
55.
Sun, C.T. and Chen, J.L. (1993). A Plastic Potential Function Suitable for Anisotropic Fiber Composites , Journal of Composite Materials, 27(14): 1379-1390 .
56.
Salvi, A.G. , Waas, A.M. and Caliskan, A. (2004). Specimen Size Effects in the off-axis Compression Test of Unidirectional Carbon Fiber Tow Composites , Composites Science and Technology, 64(1): 83-97 .
57.
Quek, S.C. (2002). The Compressive and Failure of Braided Textile Composites: Experiments and Analysis, PhD Dissertation, Appendix C, Aerospace Engineering, The University of Michigan.
ABAQUS Inc. , ABAQUS User Manual, Version 6.3, Pawtucket, RI.
60.
Johnson, E.R. , Kapania, R.K. , Dillard, D.A. , Makhecha, D. and Simon, J. (2003). Response and Failure of Adhesively Bonded Automotive Composite Structures under Impact Loads, Private Communication, September 2003.
