This paper investigates the effect of polypropylene type and cellulose content on the foaming behavior of cellulose fiber-reinforced polypropylene composites in extrusion. Two types of polypropylene (linear and branched structures) were used as a polymer matrix. The thermal properties of the composites were characterized by a differential scanning calorimeter, and the viscosity of the composites was evaluated by a rotational rheometer. The foaming behavior of the composites was examined using an extrusion foaming system, in which carbon dioxide was used as a physical blowing agent for foams. The results suggested that the cell density increased with the increase of cellulose content. On the other hand, the void fraction decreased with the addition of cellulose, but the void fraction at the 40 wt% cellulose was higher than that at the 20 wt% cellulose. The results also indicated that the two types of polypropylene had a minimal effect on the foaming behaviors of the cellulose fiber composites.
RätzschMBuckaHHesseA. Challenges in polypropylene by chemical modification. Macromol Symp1998; 129: 53–77.
2.
Rätzsch M, Panzer U, Hesse A, et al. Developments in high melt strength PP: Technology, properties, applications and markets. In: Society of Plastics Engineers Annual Technical Conference. New York, USA, 1999, pp.2071–2075.
3.
NaguibHEParkCBPanzerU. Strategies for achieving ultra low-density polypropylene foams. Polym Eng Sci2002; 42: 1481–1492.
4.
RodrigueDSouiciSTwite-KabambaE. Effect of wood powder on polymer foam nucleation. J Vinyl Addit Technol2006; 12: 19–24.
5.
RizviGMatuanaLMParkCB. Foaming of PS/wood fiber composites using moisture as a blowing agent. Polym Eng Sci2000; 40: 2124–2132.
6.
RizviGMPop-IlievRParkCB. A novel system design for continuous processing of plastic/wood-fiber composite foams with improved cell morphology. J Cell Plast2002; 38: 367–383.
7.
RizviGMParkCBLinWS. Expansion mechanisms of plastic/wood-flour composite foams with moisture, dissolved gaseous volatiles, and undissolved gas bubbles. Polym Eng Sci2003; 43: 1347–1360.
8.
ZhangHRizviGMParkCB. Development of an extrusion system for producing fine-celled HDPE/wood-fiber composite foams using CO2 as a blowing agent. Adv Polym Technol2004; 23: 263–276.
9.
GuoGRizviGMParkCB. Critical processing temperature in the manufacture of fine-celled plastic/wood-fiber composite foams. J Appl Polym Sci2004; 91: 621–629.
10.
RizviGMGuoGParkCB. Critical issues in extrusion foaming of plastic/woodfiber composites (Review). Cell Polym2005; 24: 347–362.
11.
Guo G, Wang KH, Rizvi GM, et al. Effects of wood-fiber content on the density and morphology of mPE/wood-fiber composites. In: Polymer Processing Society 20th annual meeting, Akron, Ohio, USA, 2004.
12.
Guo G, Rizvi GM, Park CB, et al. Extrusion foaming of woodfiber/plastic composites with gas injection. In: Polymer Processing Society 21st annual meeting, Leipzig, Germany, 2005.
13.
ZhangJRizviGMParkCB. Effects of wood fiber content on the rheological properties, crystallization behavior, and cell morphology of extruded wood fiber/HDPE composites foams. BioResources2011; 6: 4979–4989.
14.
SainMSuharaPLawS. Interface modification and mechanical properties of natural fiber-polyolefin composite products. J Reinf Plast Compos2005; 24: 121–130.
15.
KubokiTLeeYHParkCB. Mechanical properties and foaming behavior of cellulose fiber reinforced high-density polyethylene composites. Polym Eng Sci2009; 49: 2179–2188.
16.
DeNicolaAJGalambosAFWolkowiczMD. Radiation treatment of polypropylene, Washington, DC: ACS, 1992, pp. 106–107.
17.
WangXTzoganakisCRempelGL. Chemical modification of polypropylene with peroxide/pentaerythritol triacrylate by reactive extrusion. J Appl Polym Sci1996; 61: 1395–1404.
18.
NaguibHEParkCBSongSW. Effect of supercritical gas on crystallization of linear and branched polypropylene resins with foaming additives. Ind Eng Chem Res2005; 44: 6685–6691.
19.
ColomXCañavateJPagèsP. Changes in crystallinity of the HDPE matrix in composites with cellulosic fiber using DSC and FTIR. J Reinf Plast Compos2000; 19: 818–830.
20.
GañánPMondragonI. Thermal and degradation behavior of fique fiber reinforced thermoplastic matrix composites. J Therm Anal Calorim2003; 73: 783–795.
21.
SombatsompopNKositchaiyongAWimolmalaE. Experimental analysis of temperature and crystallinity profiles of wood sawdust/polypropylene composites during cooling. J Appl Polym Sci2006; 102: 1896–1905.
22.
SatoYFujiwaraKTakikawaT. Solubilities and diffusion coefficients of carbon dioxide and nitrogen in polypropylene, high-density polyethylene, and polystyrene under high pressures and temperatures. Fluid Phase Equilibr1999; 162: 261–276.
23.
LiGWangJParkCB. Measurement of gas solubility in linear/branched PP melts. J Polym Sci Part B: Polym Phys2007; 45: 2497–2508.
24.
GibbsJW. The scientific papers of J. Willard Gibbs, New York: Dover, 1961.
25.
BlanderMKatzJL. Bubble nucleation in liquids. AlChE J1975; 21: 833–848.
26.
WangCLeungSNBussmannM. Numerical investigation of nucleating-agent-enhanced heterogeneous nucleation. Ind Eng Chem Res2010; 49: 12783–12792.
27.
WongAChuRKMLeungSN. A batch foaming visualization system with extensional stress-inducing ability. Chem Eng Sci2011; 66: 55–63.
28.
LeungSNWongAWangLC. Mechanism of extensional stress-induced cell formation in polymeric foaming processes with the presence of nucleating agents. J Supercrit Fluids2012; 63: 187–198.
29.
LeeS-T. Shear effects on thermoplastic foam nucleation. Polym Eng Sci1993; 33: 418–422.
30.
LeungSNWongAGuoQ. Change in the critical nucleation radius and its impact on cell stability during polymeric foaming processes. Chem Eng Sci2009; 64: 4899–4907.
31.
LeeJWSParkCB. Use of nitrogen as a blowing agent for the production of fine-celled high-density polyethylene foams. Macromol Mater Eng2006; 291: 1233–1244.
