Sage Journals: Discover world-class research

Abstract

The use of polymer microspheres for producing fine-cellular foams is a new development in rotational molding. In previous studies, some reduction in mechanical properties has been found due to the immiscibility between the polymer shell and the matrix polymer. Coupling agents can act as a molecular bridge at this interface and can also affect bubble growth by altering the rheological properties of the matrix polymer as well as the microsphere shell material. The influence of different coupling agents on the melt properties of several resins was investigated, as well as the effect of these coupling agents on the mechanical properties of foamed rotationally molded parts.

Get full access to this article

View all access options for this article.

References

1. Beall, G.L. (1998). Rotational Molding, Design, Materials, Tooling and Processing, Hanser Publishers, Munich, Germany .

2. Liu, G., Park, C.B. and Lefas, J. (1998). Production of Low Density LLDPE Foams in Rotational Molding , Pol. Eng. Sci., 38(12).

3. Liu, S.J. and Tsai, C. (1998). An Experimental Study of Foamed Polyethylene in Rotational Molding, SPE ANTEC, p. 1161-1161.

4. Takacs, E., Vlachopoulos, J. and Lipsteuer, S.J. (1999). Foamable Micropellets and Blended Forms of Polyethylene for Rotational Molding, SPE RETEC, Cleveland .

5. Iliev, R.P. and Park, C.B. (2000). Processing of Polypropylene Foams in Melt Compounding Based Rotation Foam Molding, SPE ANTEC, p. 1314-1314.

6. Iliev, R.P. and Park, C.B. (2001). Importance of Timely Polymer Sintering Versus Blowing Agent Decomposition in Rotational Foam Molding of Polypropylene, SPE ANTEC, p. 1312-1312.

7. Kearns, M.P., Callan, N.M., Miller, S.J. and Crawford, R.J. (January 2000). The Use of Hollow Microspheres in the Rotational Moulding of Plastic Parts, Part 1: Single Layer Mouldings, Rotation.

8. Kearns, M.P., Callan, N.M., Miller, S.J. and Crawford, R.J. (March–April 2000). The Use of Hollow Microspheres in the Rotational Moulding of Plastic Parts, Part 2: Two-Layer Mouldings, Rotation.

9. Kearns, M.P., Callan, N.M., Miller, S.J. and Crawford, R.J. (May–June 2000). The Use of Hollow Microspheres in the Rotational Molding of Plastic Parts, Part 3: Three-Layer Mouldings, Rotation.

10.

10. D’Agostino, D., Takács, E. and Vlachopoulos, J. (2003). The Effect of Coupling Agents on Foaming with Polymer Microspheres in Rotational Molding, SPE ANTEC, p. 1205-1205.

11.

11. Takács, E., Vlachopoulos, J. and Rosenbusch, C. (2002). Foaming with Microspheres in Rotational Molding, SPE ANTEC, p. 1271-1271.

12.

12. Technical Information from Akzo Nobel.

13.

13. Robert, A. and Crawford, R.J. (1999). The Effect of Fillers on the Properties of Rotationally Moulded Polyethylene, SPE ANTEC, p. 1478-1478.

14.

14. Wisley, B.G. (1999). The Rotational Molding of Glass Fibre Reinforced Polyethylene, SPE ANTEC, p. 1487-1487.

15.

15. Monte, S.J. Ken-React Reference Manual–Titanate, Zirconate and Aluminate Coupling Agents, Technical Information from Ken-React, Kenrich Petrochemicals, Inc., Bayonne, NJ., U.S.A.

16.

16. Jandel Scientific Software (1996). SigmaScan Pro 3.0, Image Measurement Software.

17.

17. Street, J.R. (1968). Trans. Soc. Rheol., 12: 103-103 .

18.

18. Suh, K.W. and Webb, D.D. (1985). Encyclopedia of Polymer Sci and Technology, Vol. 3, pp. 1–59, 2nd edn, John Wiley and Sons, USA .

19.

19. Cogswell, F.N. (1996). Polymer Melt Rheology, Woodhead Publishing, Cambridge UK .

Foaming with Polymer Microspheres in Rotational Molding: The Effect of Coupling Agent

Abstract

Get full access to this article

References