Modeling of Process Induced Residual Stresses in Resin Transfer Molded Composites with Woven Fiber Mats

Abstract

Cure-dependent mechanical properties are used in finite element-based models to determine process-induced residual stresses and deformations in composite parts. The complete cure cycle in resin transfer molding process is modeled in a series of sub steps. The composite mechanical properties are specified in each step according to the composite cure history. The cool down stage after the composite cure is also analyzed. The effects of resin shrinkage on the development of residual stresses and deformations are investigated as well. Case studies involving composite parts with woven carbon and fiberglass mats and epoxy resin are presented to demonstrate the effectiveness of the developed models. Residual stresses were found to be compressive throughout the investigated composite parts. Resin shrinkage resulted in a decrease in residual stresses. The present study establishes the bases for quantifying the combined effects of thermomechanical and thermochemical responses of the material on the development of process induced residual stresses and deformations in resin transfer molded composites.

Keywords

residual stresses resin transfer molding woven fiber mat finite element analysis

Get full access to this article

View all access options for this article.

References

1. Richardson,T. , “Composites, A Design Guide,” Industrial Press Inc., New York, NY, 1987, pp. 217–238.

2. Cai, Z. , “Simplified Mold Filling Simulation in Resin Transfer Molding,” Journal of Composite Materials, Vol. 26, no. 17, 1992, pp. 2606–2630.

3. White, S. R. and Hahn, H. T. , “Process Modeling of Composite Materials: Residual Stress Development During Cure. Part I. Model Formulation,” Journal of Composite Materials, Vol. 26, No. 16, 1992, pp. 2402–2422.

4. White, S. R. and Hahn, H. T. , “Process Modeling of Composite Materials: Residual Stress Development During Cure. Part II. Experimental Validation,” Journal of Composite Materials, Vol. 26, No. 16, 1992, pp. 2423–2453.

5. White, S. R. and Hahn, H. T. , “Cure Cycle Optimization for the Reduction of Processing-Induced Residual Stresses in Composite Materials,” Journal of Composite Materials, Vol. 27, No. 14, 1993, pp. 1352–1378.

6. Osswald, T. A. , Sun, E. M. , and Tseng, S.-C. , “Experimental Verification on Simulating Shrinkage andWarpage of Thin Compression MouldedSMCParts,” Polymers& Polymer Composites, Vol. 2, No. 3, 1994, pp. 187A–198A.

7. Bogetti, T. A. and Gillespie, J. W. Jr. , “Residual Stress and Deformation in Thick Laminate CompositesUndergoing Chemical Hardening and Shrinkage,” 45th Annual Conference, Composites Institute, The Society of the Plastic Industry, Inc., February 12–15, 1990, pp. 19-A1/1–19-A1/8.

8. Bogetti, T. A. and Gillespie, J. W. Jr. , “Process-Induced Stress and Deformation in Thick-Section Thermosetting Composite Laminates,” 21st International SAMPE Technical Conference, September 25–28, 1989, pp. 947–959.

9. Bogetti, T. A. and Gillespie, J. W. Jr. , “Process-Induced Stress and Deformation in Thick-Section Thermosetting Composite Laminates,” Journal of Composite Materials, Vol. 26, No. 5, 1992, pp. 626–658.

10.

10. Kumazawa, H. , “Prediction of Anisotropic Shrinkage of an Injection Molded Part,” ANTEC, 1994, pp. 817–821.

11.

11. Golestanian, H. and El-Gizawy A. S. , “Cure Dependent Lamina Stiffness Matrices of Resin Transfer Molded Composite Parts with Woven Fiber Mats,” Journal of Composite Materials, in press, 1997.

12.

12. Ellis, B. , Chemistry and Technology of Epoxy Resins, First Edition, Chapman & Hall, New York, 1993.

13.

13. Bruins, P. F. , Epoxy Resins Technology, John Wiley & Sons, Inc., New York, 1968.

14.

14. Wang, H.-S. and Chou, T-.W. , “Transient Thermal Stress Analysis of a Rectangular Orthotropic Slab,” Journal of Composite Materials, Vol. 19, September 1985, pp. 424–441.

15.

15. Chan, A. W. and Hwang, S.-T. , “Modeling Resin Transfer Molding of Axisymmetric Composite Parts,” Journal of Materials Processing and Manufacturing Science, Vol. 1, no. 1, 1992, pp. 105–118.

16.

16. Perry, M. J. , Wang, T. J. , Ma, Y. , and Lee, L. J. , “Resin Transfer Molding of Epoxy/Graphite Composites,” 24th InternationalSAMPETechnical Conference, October 20–22, 1992, pp. T421–T435.