Fundamental Understanding of Piezoelectric Strain Sensors

Abstract

This paper investigates the behavior of piezoelectric elements as strain sensors. Strain is measured in terms of the charge generated by the element as a result of the direct piezoelectric effect. Strain measurements from piezoceramic (PZT) and piezofilm (PVDF) sensors are compared with strains from a conventional foil strain gage and the advantages of each type of sensor are discussed, along with their limitations. The sensors are surface bonded to a beam and are calibrated over a frequency range of 5-500 Hz. Correction factors to account for transverse strain and shear lag effects due to the bond layer are analytically derived and experimentally validated. The effect of temperature on the output of PZT strain sensors is investigated. Additionally, design of signal conditioning electronics to collect the signals from the piezoelectric sensors is addressed. The superior performance of piezoelectric sensors compared to conventional strain gages in terms of sensitivity and signal to noise ratio is demonstrated.

Get full access to this article

View all access options for this article.

References

IEEE Standard on Piezoelectricity. 1987. ANSI/IEEE, Std. 176.

Morgan Matric Inc. Piezoceramic Databook. 1993. Morgan Matroc Inc., Electroceramics Division.

Anderson, E. H. and N. W. Hagood . 1994. “Simultaneous Piezoelectric Sensing/Actuation: Analysis and Application to Controlled Structures,” Journal of Sound and Vibration, 174(5): 617-639.

Brown, R. F. 1961. “Effect of Two-Dimensional Mechanical Stress on the Dielectric Properties of Ceramic Barium Titanate and Lead Zirconate Titanate,” Canadian Journal of Physics, 39: 741-753.

Brown, R. F. and G. W. McMahon . 1962. “Material Constants of Ferroelectric Ceramics at High Pressure,” Canadian Journal of Physics, 40: 672-674.

Chopra, I. 1996. “Review of Current Status of Smart Structures and Integrated Systems,” SPIE Smart Structures and Integrated Systems, 2717: 20-62.

Crawley, E. F. and J. de Luis . 1987. “Use of Piezoelectric Actuators as Elements of Intelligent Structures,” AIAA Journal, 25(10): 1373-1385.

Dally, J. W. , W. F. Riley and K. G. McConnell . 1993. Instrumentation for Engineering Measurements. John Wiley and Sons, Inc.

Esteban, J. , F. Lalande and C. A. Rogers . 1996. “Parametric Study on the Sensing Region of a Collocated PZT Actuator-Sensor,”

Proceedings, 1996 SEM VIII International Congress on Experimental Mechanics.

10.

Hanagud, S. , M. W. Obal and A. J. Calise . 1992. “Optimal Vibration Control by the Use of Piezoelectric Sensors and Actuators,” Journal of Guidance, Control and Dynamics, 15(5): 1199-1206.

11.

Inman, D. J. , J. J. Dosch and E. Garcia . 1992. “A Self-Sensing Piezoelectric Actuator for Collocated Control,” Journal of Intelligent Materials and Smart Structures, 3: 166-185.

12.

Kreuger, H. H. A. 1967. “Stress Sensitivity of Piezoelectric Ceramics: Pt. I. Sensitivity to Compressive Stress Parallel to the Polar Axis,” Journal of the Acoustical Society of America, 42: 636-645.

13.

Kreuger, H. H. A. 1968. “Stress Sensitivity of Piezoelectric Ceramics: Pt. III. Sensitivity to Compressive Stress Perpendicular to the Polar Axis,” Journal of the Acoustical Society of America, 43: 583-591.

14.

Lee, C. K. and T. O’Sullivan . 1991. “Piezoelectric Strain Rate Gages,” Journal of the Acoustical Society of America, 90(2): 945-953.

15.

Lee, C. K. , T. C. O’Sullivan and W. W. Chiang . 1991. “Piezoelectric Strain Rate Sensor and Actuator Designs for Active Vibration Control,” Proceedings of the 32nd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference, (4): 2197-2207.

16.

Lin, M. W. and C. A. Rogers . 1993. “Modeling of the Actuation Mechanism in a Beam Structure with Induced Strain Actuators,” AIAA-93-1715-CP.

17.

Lin, M. W. and C. A. Rogers . 1994. “Bonding Layer Effects on the Actuation Mechanism of an Induced Strain Actuator/Substructure System,” SPIE, 2190: 658-670.

18.

Mattiat, O. E. , 1971. Ultrasonic Transducer Materials, Plenum Press, New York.

19.

Qui, J. and J. Tani . 1995. “Vibration Control of a Cylindrical Shell Using Distributed Piezoelectric Sensors and Actuators,” Journal of Intelligent Material Systems and Structures, 6(4): 474-481.

20.

Samuel, P. and D. Pines . 1997. “Health Monitoring/Damage Detection of a Rotorcraft Planetary Geartrain Using Piezoelectric Sensors,” Proceedings of SPIE’s 4th Annual Symposium on Smart Structures and Materials, San Diego, CA, 3041: 44-53.

21.

Stout, D. F. 1976. Handbook of Operational Amplifier Circuit Design. McGraw-Hill Book Company.

22.

Varadan, V. K. , X. Bao , C.-C. Sung and V. V. Varadan . 1989. “Vibration Control of Flexible Structures Using Piezoelectric Sensors and Actuators,” Journal of Wave-Material Interaction, 4(1-3): 65-81.