In this paper, effect of minor additions of magnesium content in the form of master alloys on the high-temperature dry sliding wear behaviour for A356 alloy has been reported. Alloy composition, normal pressures and sliding distances on A356 alloy at constant temperature of 300°C was studied. The cast alloys and worn surfaces were characterized by SEM/EDX microanalysis. The results indicate that the wear rate of A356 alloy increases with an increase in normal pressures and sliding distances in all the cases and decreases when 0.7% Mg is added to A356 alloy. The decrease in wear rate after the addition of Mg is mainly due to changes in microstructure which lead to improvement in mechanical properties. Further, worn surface study indicates that the formation of iron-rich oxide layer between the mating surfaces during sliding improves sliding wear performance.
VenkataramanB, SundararajanG.Correlation between the characteristics of the mechanically mixed layer and wear behaviour of aluminium Al-7075 alloy and Al-MMCs. Wear, Elsevier Science, UK. 2000;245:22–38.
2.
TorbianH, PathakJP, TiwariSN.Wear characteristics of Al-Si alloys. Wear. 1994;172:49–58.
3.
GruzleskiJE, ClossetBM.Liquid treatment to Al-Si alloys. Illinois: AFS; 1990.
4.
KoriSA. (2000). ‘Grain refinement and modification of some hypoeutectic and eutectic Al-Si alloys,’ Ph. D Thesis, IIT Kharagpur.
5.
KumariS, PillaiSS, and PaiRM, . Effect of iron in Al-7Si-0.3Mg alloy. Indian Foundry J. 2002;48(1):27–31.
6.
SarkarAD.Wear of aluminium-silicon alloys. Wear. 1975;31:331–343.
7.
SarkarAD.Wear of metals. Oxford: Pergaman Press; 1976. p. 50–160.
DwivediDK, SharmaA, RajanTV.Friction and wear behaviour of cast hypereutectic Al-Si alloys at low sliding velocities. Trans Indian Inst Metals. 2001;6:247–254.
10.
ChandrashekharaiahTM, KoriSA.Effect of grain refinement and modification on the dry sliding wear behaviour of eutectic Al-Si alloys. J Tribology Int. 2009;42(1):59–65.
11.
SagstadT, DahleN.Grain refining of hypoeutectic aluminium-silicon alloys with TiBloy, proceedings of the Fifth International AFS Conference on Molten Aluminium Processing. American Foundry Men's Society, Orlando. 1998: 100–116.
12.
ShabestariG, MoemeniH.Effect of copper and solidification conditions on the microstructure and mechanical properties of Al-Si-Mg alloys. J Mater. Process Tech. 2004;153-154:193–198.
13.
YeH.An overview of the development of Al-Si alloybased material for engine applications. J Mater Eng Perform. 2003;12(3):288–297.
14.
ClarkeDS, VarneyR. Wilbur ‘Physical metallurgy for engineers,’ second ed. Princeton (NJ): D. Van Nostard; 1962.
15.
Garcia-HnojosaJA, GonzalezCR, GonzalezGM, . Structure and properties of Al7Si-Ni and Al-7Si-Cu cast alloys nonmodified and modified with Sr. J Mater Process Technol. 2003;143-144b:306–310.
16.
MondlofoLF.Aluminium alloys-structure and properties. London: Butterworths; 1976, pp. 249-250.
17.
MohantyPS, GruzleskiJE.Grain refinement mechanisms of hypoeutectic Al-Si alloys. Acta materialia.1996;44(9):3749–3760.
18.
AnasyidaAN, DaudAR, GhbyajaliMJ.Dry sliding wear behaviour of Al-4Si-4Mg alloys by the addition of cerium. Int J Mech Mater. Eng. 2009;4(2):127–130.
19.
HatchJE.Aluminium properties and physical metallurgy. Metals Park (OH): ASM; 1984 44073, 1-104, 200-241, p. 320–350.
20.
SahebN, LaouiT, DaudAR, . Influence of Ti addition on wear properties of Al-Si eutectic alloys. Wear. 2001;249:656–662.
21.
DwivediDK, SharmaA, RajanTV.Influence of 5/1 Ti-B-Al and Strontium on cast Eutectic Al-Si base alloys. Proc. of the 49th Indian Foundry Congress; 2001, p. 103–108.
22.
DwivediDK.Wear behaviour of cast hypereutectic aluminium silicon alloys. Mater Des. 2006;27:610–616.
23.
RohatgiPK, PaiBC.Effect of microstructure and mechanical properties on the seizure resistance of cast aluminium alloys. June 1974;28(3):353–367.
24.
LingaurdS, FuKH, ChuengKH.Some observations on the wear of aluminium rubbing on steel. Wear. 1984;96:75–84.
SamuelFH, OuelletP, SamuelAM, . Effect of Mg and Sr additions on the formation of intermetallics in Al-6wt pct Si-3.5wt pct Cu-(0.45) to (0.8) wt pct Fe 319-type alloys. Metall Mater Trans, A. 1998;29A:2871–2884.
27.
JoenoesAT, GruzleskiJE.Magnesium effects on the microstructure of unmodified and modified Al-Si alloys, Cast Metals. 1991;4(2):62–71.
28.
KashyapKT, MuraliS, RamanKS, . Overview of casting and heat treatment variables of Al-7Si-Mg alloy. Mater Sc Tech. 1993;9:189–203.
29.
WeiCZ, RuieZ.Effect of strontium on primary dendrite and eutectic temperature of A357 alloy. China Foundry. 2010;7(2):149–152.
30.
ASTM Standards, Standard test method for wear testing with Pin- On-Disc Apparatus, Designation G99- 90, ASTM, 1916 Raco St. Philodalphia, PA19103. 1993. p 1–5.
31.
KoriSA, PrabhudevMS, ChandrashekhariahTM.Studies on the microstructure and mechanical properties of A356 alloy with minor additions of copper and magnesium. Int J Transactions of the Indian Institute of Metals (Springer Publications) (ISSN. 0972-2815). August-October 2009;62(4-5):353–356.
32.
DabbA, PhatangareA, ShelarD.Wear behavior of Hypereutectic Al-Si alloys at Elevated temperatures. International Conference on Ideas, Impact and Innovation in Mechanical Engineering (ICIIIME-2017), ISSN: 2321-8169. 2017;5(6):318–324.
33.
AthulaS, PremnathaG, SunilB, . Elevated Temperature wear behavior of Aluminium Alloy (Al 6061). National Conference on Latest Trends in Mechanical Engineering NCLTME. 2018.
34.
Vishal RM, MayurSutariaP.Effect of temperature on wear and friction behavior of as-cast and heat-treated LM25/SiC aluminum matrix composites. World J Eng. 2020;18(2):206–216.
35.
KumaranS, Srinivasa RaoT, KamarajM.High temperature dry sliding wear behaviour of Al-Si/graphite composites processed by stir casting. Miner, Met Mater (TMS-2011). 2011;2:191–198.
36.
JakanurM.Effect of Ti addition on the tribological wear behavior of hypereutectic Al-Si alloys at elevated temperatures. Special Issue on International Journal on Theoretical and Applied Research in Mechanical Engineering (IJTARME). 2016;5(1):121–128.
