The components made of cast irons require protection against wear in severe service conditions. Surface engineering can be used to prevent mechanical failures of cast iron components due to excessive friction-related wear. The iron boride-based coatings can be applied on the entire working surfaces of large-size complex shape cast iron components through the thermal diffusion process. Tribological properties of these coatings obtained have been studied using the pin-on-disc test configuration in simulating application conditions. The obtained iron boride coatings demonstrated significantly lower wear losses compared to bare cast iron, stable behaviour of coefficient of friction during time and no structural degradation and spalling. The superior wear resistance of boride-based coatings on cast iron is dealt with the combination of their high hardness, specific ‘sawtooth’ double-layer morphology obtained through the thermal diffusion process, diffusion-related bonding to the substrate, self-lubricating thin ‘tribo-film’ formed during friction and high thermal and chemical stability.
WaltonC. F. and OparT. J.: ‘Iron casting handbook’, Iron Casting Soc.; 1981.
2.
DavisJ. R.: ‘Cast irons’; 1996, Materials Park, OH, ASM International.
3.
PyeA. M.: ‘Applications of some of the newer cast irons (Technical report)’, Mater. Design, 1982, 3, (4), 534–537. doi: 10.1016/0261-3069(82)90166-2
4.
CuevaG., SinatoraA., GuesserW. L. and TschiptschinA. P.: ‘Wear resistance of cast irons used in brake discs rotors’, Wear, 2003, 255, 1256–1260. doi: 10.1016/S0043-1648(03)00146-7
5.
VermaP. C., MenapaceL., BonfantiA., CiudinR., GialanellaS. and StraffeliniG.: ‘Braking pad-disc system: wear mechanisms and formation of wear fragments’, Wear, 2015, 322–323, 251–258. doi: 10.1016/j.wear.2014.11.019
6.
BudinskiK. G.: ‘Surface engineering for wear resistance’; 1988, Englewood Cliffs, NJ, USA, Prentice-Hall Inc.
7.
DavisJ. R. (ed.): ‘Surface engineering for corrosion and wear resistance’; 2001, Materials Park, OH, USA, ASM International and IOM Communications, Maney Publishing.
8.
MittemeijerE. J. and SomersM. A. J. (ed.): ‘Thermochemical surface engineering of steels’; 2014, Cambridge, UK, Elsevier, Woodhead Publishing.
9.
SternK. H. (ed.): ‘Metallurgical and ceramic protective coatings’; 1996, London, UK, Chapman & Hall.
10.
TakadoumJ.: ‘Materials and surface engineering in tribology’; 2008, London, UK, ISTE, John Wiley & Sons.
11.
FranklinS. E. and BeugerJ.: ‘A comparison of the tribological behavior of several wear-resistant coatings’, Surf. Coat. Technol., 1992, 55, 459–465. doi: 10.1016/S0257-8972(07)80066-1
12.
StraffordK. N.: ‘Tribological properties of coatings – expectations, performance and the design dilemma’, Surf. Coat. Technol., 1996, 81, 106–117. doi: 10.1016/0257-8972(95)02651-7
13.
HogmarkS., JakobsonS. and LarssonM.: ‘Design and evaluation of tribological coatings’, Wear, 2000, 246, 20–33. doi: 10.1016/S0043-1648(00)00505-6
14.
MarpleB. R. and LimaR. S.: ‘Engineering nanostructured thermal spray coatings: process – property – performance relationships of ceramic based materials’, Adv. Appl. Ceram., 2007, 106, (5), 265–275. doi: 10.1179/174367607X202591
Chatterjee-FischerR.: ‘Boriding and diffusion metallizing’, in ‘Surface modification technologies’, (ed. SudarsanT. S.), 1989, New York, USA, Marcel Dekker Inc.
17.
DearnleyP. A. and BellT.: ‘Engineering the surface with boron based materials’, Surf. Eng., 1985, 1, (3), 203–217. doi: 10.1179/sur.1985.1.3.203
18.
HungerH.-J. and TruteG.: ‘Boronizing to produce wear-resistant surface layers’, Heat Treat. Met., 1994, 2, 31–39.
19.
MedvedovskiE., ChinskiF. A. and StewartJ.: ‘Wear- and corrosion-resistant boride-based coatings obtained through thermal diffusion CVD processing’, Adv. Eng. Mater., 2014, 16, (6), 713–728. doi: 10.1002/adem.201400090
JingxinQ., XiaoliW. and HeshengS.: ‘Abrasion behaviour of boronized layer’, Chin. J. Met. Sci. Technol., 1992, 8, 383–386.
22.
AsthanaP., UstaM., UcisikA. H. and LiangH.: ‘Wear and surface characterization of boronized pure iron’, J. Tribol., 2007, 129, (1), 1–10. doi: 10.1115/1.2401211
23.
MartiniC., PalombariniG. and CarbucicchioM.: ‘Mechanism of thermochemical growth of iron borides on iron’, J. Mater. Sci., 2004, 39, (3), 933–937. doi: 10.1023/B:JMSC.0000012924.74578.87
24.
SenU., SenS. and YilmazF.: ‘Improving the surface properties of ductile irons by boronizing’, Key Eng. Mater., 2004, 264–268, 541–544. doi: 10.4028/www.scientific.net/KEM.264-268.541
25.
SenU., SenS. and YilmazF.: ‘Effect of process time on the tribological properties of boronized GGG-80 Ductile cast iron’, Ind. Lubrication Tribol., 2005, 57, (6), 243–248. doi: 10.1108/00368790510622335
26.
Ortiz-DominguezM., Flores-RenteriaM. A., KeddamM., Elias-EspinosaM., Damian-MejiaO., Aldana-GonzalezJ. I., Zuno-SilvaJ., Median-MorenoS. A. and Gonzalez-ReyesJ. G.: ‘Simulation of growth kinetics of Fe2B layers formed on gray cast iron during the powder-pack boriding’, Mater. Technol., 2014, 48, (6), 905–916.
27.
MericC., SahinS., BackizB. and KoksalN. S.: ‘Investigation of the boronizing effect on the abrasive wear behavior in cast irons’, Mater. Design, 2006, 27, (9), 751–757. doi: 10.1016/j.matdes.2005.01.018
28.
MuD. and ShenB.-L.: ‘The kinetics and dry-sliding wear properties of boronized gray cast iron’, Adv. Mater. Sci. Eng., 2013, article ID 751971.
29.
DeuisR. L., SubramanianC. and YellupJ. M.: ‘Dry sliding wear of aluminum composites – a review’, Compos. Sci. Technol., 1997, 57, 415–435. doi: 10.1016/S0266-3538(96)00167-4
30.
KumarG. B. V., RaoC. S. P. and SelvarajN.: ‘Mechanical and tribological behavior of particulate reinforced aluminum matrix composites – a review’, J. Miner. Mater. Charact. Eng., 2011, 10, (1), 59–91.
31.
AltinkokN., OzsertI. and FindikF.: ‘Dry sliding wear behavior of Al2O3/SiC particle reinforced aluminum based MMC's fabricated by stir casting method’, Acta Phys. Pol. A, 2013, 124, (1), 11–19. doi: 10.12693/APhysPolA.124.11
32.
MedvedovskiE., JiangJ. and RobertsonM.: ‘Tribological properties of boride based thermal diffusion coatings’, Adv. Appl. Ceram., 2014, 113, (7), 427–437. doi: 10.1179/1743676114Y.0000000175
33.
MedvedovskiE., JiangJ. and RobertsonM.: ‘Iron boride-based thermal diffusion coatings for tribo-corrosion oil production applications’, Ceram. Int., 2016, 42, (2), Part B, 3190–3211. doi: 10.1016/j.ceramint.2015.10.109
34.
HutchingsI. M.: ‘Tribology. Friction and wear of engineering materials’; 1992, London, UK, Butterworth-Heinemann.
35.
RabinowiczE.: ‘Friction and wear of materials’, 2nd edn; 1995, New York, NY, USA, Wiley.
36.
BrushanB.: ‘Introduction to tribology’, 2nd edn; 2013, New York, NY, Wiley.
MedvedovskiE.: ‘Influence of corrosion and mechanical loads on advanced ceramic components’, Ceram. Int., 2013, 39, 2723–2741. doi: 10.1016/j.ceramint.2012.09.040
44.
WangY. X. and ZhangS.: ‘Toward hard yet tough ceramic coatings’, Surf. Coat. Technol., 2014, 258, 1–16. doi: 10.1016/j.surfcoat.2014.07.007
45.
CimenogluH., AtarE. and MotallebzadehA.: ‘High temperature tribological behaviour of borided surfaces based on the phase structure of the boride layer’, Wear, 2014, 309, 152–158. doi: 10.1016/j.wear.2013.10.012
46.
ErdemirA., BindalC., ZuikerC. and SavrunE.: ‘Tribology of naturally-occurring boric acid films on boron carbide’, Surf. Coat. Technol., 1996, 86–87, Part 2, 507–511. doi: 10.1016/S0257-8972(96)02984-2
47.
MorinaA. and NevilleA.: ‘Tribofilms: aspects of formation, stability and removal’, J. Phys. D Appl. Phys., 2007, 40, 5476–5487. doi: 10.1088/0022-3727/40/18/S08
48.
Fox-RabinovichG. S.: ‘Adaptive hard coatings design based on the concept of self-organization during friction’, in ‘Encyclopedia of tribology’, (eds. WangQ. J. and ChungY.-W.), 16–23; 2013, London, UK, Springer.
49.
AizawaT., MitsuoA., YamamotoS., SumitomoT. and MuraihiS.: ‘Self-lubrication mechanism via the in situ formed lubricious oxide tribofilm’, Wear, 2005, 259, (1–6), 708–718. doi: 10.1016/j.wear.2005.02.025
50.
XuJ. G. and KatoK.: ‘Formation of tribochemical layer of ceramics sliding in water and its role for low friction’, Wear, 2000, 245, 61–75. doi: 10.1016/S0043-1648(00)00466-X
51.
BiswasS. K.: ‘Some mechanisms of tribofilm formation in metal/metal and ceramic/metal sliding interactions’, Wear, 2000, 245, (1–2), 178–189. doi: 10.1016/S0043-1648(00)00477-4
