To understand the service behaviour of SiC fibres, the effects of ambient environment and temperature on the microstructure, mechanical property and oxidation behaviour of these fibres were investigated. The result shows that, the surface of SiC fibres becomes rough after exposure in air from 973 to 1573 K due to the formation of small SiO2 particles, and a smooth SiO2 film will be formed on the SiC fibre at 1773 K. In Ar atmosphere, SiC fibres will change into clusters of large SiC crystals after heat treatment for 2 h at 2373 K. The tensile strength of SiC fibres decreased by 66 and 95% when the fibres were exposed at 1773 K for 5 min in air and 2373 K for 2 h in Ar, respectively. This degradation is associated with the evaporation of CO and SiO from the fibres as well as with SiC grain growth in the fibres.
LiuH., ChengH., WangJ. and TangG.: ‘Dielectric properties of the SiC fiber-reinforced SiC matrix composites with the CVD SiC interphases’, J. Alloys Compd., 2010, 491, 248–251. doi: 10.1016/j.jallcom.2009.09.163
2.
KondoS., HinokiT., NonakaM. and OzawaK.: ‘Irradiation-induced shrinkage of highly crystalline SiC fibers’, Acta Mater., 2015, 83, 1–9. doi: 10.1016/j.actamat.2014.07.057
3.
BaklanovaN. I., KiselyovaO. I., TitovA. T. and ZimaT. M.: ‘Microstructural features of the ZrO2 interfacial coatings on SiC fibers before and after exposition to air at high temperatures’, J. Eur. Ceram. Soc., 2008, 28, 1687–1696. doi: 10.1016/j.jeurceramsoc.2007.11.008
4.
BuetE., SauderC., SorninD., PoissonnetS., RouzaudJ. N. and Vix-GuterlC.: ‘Influence of surface fibre properties and textural organization of a pyrocarbon interphase on the interfacial shear stress of SiC/SiC minicomposites reinforced with Hi-Nicalon S and Tyranno SA3 fibres’, J. Eur. Ceram. Soc., 2014, 34, 179–188. doi: 10.1016/j.jeurceramsoc.2013.08.027
5.
YoshidaK., AkimotoH., YanoT., KotaniM. and OgasawaraT.: ‘Mechanical properties of unidirectional and crossply SiCf/SiC composites using SiC fibers with carbon interphase formed by electrophoretic deposition process’, Prog. Nucl. Energy, 2015, 82, 148–152. doi: 10.1016/j.pnucene.2014.07.027
6.
ChuY., LiH., LiL. and QiL.: ‘Oxidation protection of C/C composites by ultra-long SiC nanowire-reinforced SiC–Si coating’, Corros. Sci., 2014, 84, 204–208. doi: 10.1016/j.corsci.2014.03.029
7.
NyutuE. K. and SuibS. L.: ‘Experimental design in the deposition of BN interface coatings on SiC fibers by chemical vapor deposition’, Surf. Coat. Technol., 2006, 201, 2741–2748. doi: 10.1016/j.surfcoat.2006.05.026
8.
MorishitaK., OchiaiS., OkudaH., InshikawaT., SatoM. and InoueT.: ‘Fracture toughness of a crystalline silicon carbide fiber (Tyranno-SA3®)’, J. Am. Ceram. Soc., 2006, 89, 2571–2576. doi: 10.1111/j.1551-2916.2006.01116.x
9.
YaoR., FengZ., ChenL., ZhangY. and ZhangB.: ‘Oxidation behavior of Hi-Nicalon SiC monofilament fibres in air and O2–H2O–Ar atmospheres’, Corros. Sci., 2012, 57, 182–191. doi: 10.1016/j.corsci.2011.12.019
10.
LuoX., YangY. Q., LiuY. C., MaZ. J., YuanM. N. and ChenY.: ‘The fabrication and property of SiC fiber reinforced copper matrix composites’, Mater. Sci. Eng., A, 2007, 459, 244–250. doi: 10.1016/j.msea.2007.01.010
11.
MorishitaK., MatsumotoT., OchiaiS., OkudaH., IshikawaT. and SatoM.: ‘Degradation mechanism of amorphous silicon carbide fiber due to air-exposure at high temperatures’, Mater. Trans., 2007, 48, 111–116. doi: 10.2320/matertrans.48.111
12.
ZhangX., OuyangJ., LiuZ., WangY. and ZhouY.: ‘Crack-healing behavior of hot-pressed TZ3Y20A-SiC ceramics’, Ceram. Int., 2014, 40, 6611–6615. doi: 10.1016/j.ceramint.2013.11.117
13.
MuY., ZhouW., WangC., LuoF., ZhuD. and DingD.: ‘Mechanical and electromagnetic shielding properties of SiCf/SiC composites fabricated by combined CVI and PIP process’, Ceram. Int., 2014, 40, 10037–10041. doi: 10.1016/j.ceramint.2014.02.103
14.
LuoX., JiX., YangY., ZhangW., LiuS. and XiaoZ.: ‘Microstructure evolution of C/Mo double-coated SiC fiber reinforced Ti6Al4V composites’, Mater. Sci. Eng., A, 2014, 597, 95–101. doi: 10.1016/j.msea.2013.12.077
15.
PientiL., SilvestroniL., LandiE., MelandriC. and ScitiD.: ‘Microstructure, mechanical properties and oxidation behavior of TaC- and HfC-based materials containing short SiC fiber’, Ceram. Int., 2015, 41, 1367–1377. doi: 10.1016/j.ceramint.2014.09.070
16.
MuY., ZhouW., LuoF. and ZhuD.: ‘Effects of BN/SiC dual-layer interphase on mechanical and dielectric properties of SiCf/SiC composites’, Ceram. Int., 2014, 40, 3411–3418. doi: 10.1016/j.ceramint.2013.09.091
17.
MahT., HechtN. L., McCullumD. E., HoenigmanJ. R., KimH. M., KatzA. P. and LipsittH. A.: ‘Thermal stability of SiC fibres (Nicalon)’, J. Mater. Sci., 1984, 19, 1191–1201. doi: 10.1007/BF01120029
18.
VahlasC., RocaboisP. and BernardC.: ‘Thermal degradation mechanisms of Nicalon fibre: a thermodynamic simulation’, J. Mater. Sci., 1994, 29, 5839–5846. doi: 10.1007/BF00366865
19.
ChollonG., PaillerR., NaslainR., LaananiF., MonthiouxM. and OlryP.: ‘Thermal stability of a PCS-derived SiC fibre with a low oxygen content (Hi-Nicalon)’, J. Mater. Sci., 1997, 32, 327–347. doi: 10.1023/A:1018541030308
20.
ZhuangL., FuQ. G., LiuT. Y. and TanB. Y.: ‘In-situ PIP-SiC NWs-toughened SiC–CrSi2–Cr3C2–MoSi2–Mo2C coating for oxidation protection of carbon/carbon composites’, J. Alloys Compd., 2016, 675, 348–354. doi: 10.1016/j.jallcom.2016.03.126
21.
FuQ. G., LiH. J., WangY. J., LiK. Z. and WuH.: ‘A Si–SiC oxidation protective coating for carbon/carbon composites prepared by a two-step pack cementation’, Carbon, 2009, 35, 2525–2529.
22.
KajiakawaY., NodaS. and KomiyamaH.: ‘Preferred orientation of chemical vapor deposited polycrystalline silicon carbide films’, Chem. Vap. Deposition, 2002, 8, 99–104. doi: 10.1002/1521-3862(20020503)8:3<99::AID-CVDE99>3.0.CO;2-C
23.
MinatoK. and FukudaK.: ‘Structure of chemically vapour deposited silicon carbide for coated fuel particles’, J. Mater. Sci., 1988, 23, 699–706. doi: 10.1007/BF01174708
24.
ChinJ., GantzelP. K. and HudsonR. G.: ‘The structure of chemical vapor deposited silicon carbide’, Thin Solid Films, 1977, 40, 57–72. doi: 10.1016/0040-6090(77)90103-1
25.
WangH., LinL., YangW., XieZ. and AnL.: ‘Preferred orientation of SiC nanowires induced by substrates’, J. Phys. Chem. C, 2010, 114, 2591–2594. doi: 10.1021/jp911911e
26.
TakedaM., SakamotoJ., ImaiY. and IchikawaH.: ‘Thermal stability of the low-oxygen-content silicon carbide fiber, Hi-NicalonTM’, Compos. Sci. Technol., 1999, 59, 813–819. doi: 10.1016/S0266-3538(99)00012-3
27.
LewinsohnC. A., GiannuzziL. A., BakisC. E. and TresslerR. E.: ‘High-temperature creep and microstructural evolution of chemically vapor-deposited silicon carbide fibers’, J. Am. Ceram. Soc., 1999, 82, 407–413. doi: 10.1111/j.1551-2916.1999.tb20077.x
28.
ChollonG., VallerotJ. M., HelaryD. and JouannigotS.: ‘Structural and textural changes of CVD-SiC to indentation, high temperature creep and irradiation’, J. Eur. Ceram. Soc., 2007, 27, 1503–1511. doi: 10.1016/j.jeurceramsoc.2006.05.038
29.
TangX., ChenL., ChengX. and GuH.: ‘Temperature-dependent microstructure and phase evolution of iron-containing SiC fibers’, Ceram. Int., 2014, 40, 14223–14227. doi: 10.1016/j.ceramint.2014.06.011
30.
BuetE., SauderC., PoissonnetS., BrenderP., GadiouR. and Vix-GuterlC.: ‘Influence of chemical and physical properties of the last generation of silicon carbide fibres on the mechanical behaviour of SiC/SiC composite’, J. Eur. Ceram. Soc., 2012, 32, 547–557. doi: 10.1016/j.jeurceramsoc.2011.09.023
31.
ShaJ. J., NozawaT., ParkJ. S., KatohY. and KohyamaA.: ‘Effect of heat treatment on the tensile strength and creep resistance of advanced SiC fibers’, J. Nucl. Mater., 2004, 32, 592–596. doi: 10.1016/j.jnucmat.2004.04.123
