Flash sintering is a novel and emerging route for sintering ceramics within a few seconds, even under pressure-less conditions. In the current study, hydroxyapatite (HA) was fully densified by flash sintering at a furnace temperature of 1020°C. Flash sintering with constant electric fields of 750 and 1000 V cm−1 reduced the grain growth rate significantly compared to that sintered in the absence of an electric field at 1400°C. The microstructure of HA consolidated by flash sintering was compared with that of the without electric field sintered samples. The flash-sintered samples showed smaller grains (160 ∼ 320 nm) than the without electric field sintered samples (∼15 µm). The samples with a higher applied electric field showed slightly better densification than those with the lower field by flash sintering. Overall, the electric flash reduces the sintering temperature effectively and decreases the holding time to densify highly insulating ceramics, such as HA.
ColognaM., RashkovaB. and RajR.: ‘Flash sintering of nanograin zirconia <5 s at 850°C’, J. Am. Ceram. Soc., 2010, 93, 3556–3559. doi: 10.1111/j.1551-2916.2010.04089.x
2.
HaoX., LiuY., WangZ., QiaoJ. and SunK.: ‘A novel sintering method to obtain fully dense gadolinia doped ceria by applying a direct current’, J. Power Sources, 2012, 210, 86–91. doi: 10.1016/j.jpowsour.2012.03.006
3.
KarakuscuA., ColognaM., YarotskiD., WonJ., FrancisJ. S. C., RajR. and UberuagaB. P.: ‘Defect structure of flash-sintered strontium titanate’, J. Am. Ceram. Soc., 2012, 95, 2531–2536. doi: 10.1111/j.1551-2916.2012.05240.x
4.
SolvasE. Z., BonillaS., WilshawP. R. and ToddR. I.: ‘Preliminary investigation of flash sintering of SiC’, J. Eur. Ceram. Soc., 2013, 33, 2811–2816. doi: 10.1016/j.jeurceramsoc.2013.04.023
5.
YoshidaH., SakkaY., YamamotoT., LebrunJ.-M. and RajR.: ‘Densification behaviour and microstructural development in undoped yttria prepared by flash-sintering’, J. Eur. Ceram. Soc., 2014, 34, 991–1000. doi: 10.1016/j.jeurceramsoc.2013.10.031
6.
FrancisJ. S. C., ColognaM. and RajR.: ‘Particle size effects in flash sintering’, J. Eur. Ceram. Soc., 2012, 32, 3129–3136. doi: 10.1016/j.jeurceramsoc.2012.04.028
7.
EslamiH., Solati-HashjinM. and TahririM.: ‘Effect of fluorine ion addition on structural, thermal, mechanical, solubility and biocompatibility characteristics of hydroxyapatite nanopowders’, Adv. Appl. Ceram., 2010, 109, 200–212. doi: 10.1179/174367509X12503626841550
8.
MonmaturapojN., ThepsuwanW., Mai-NgamK.NgernpimaiS.KlinsukhonW. and PrahsarnC.: ‘Preparation and properties of hydroxyapatite/titania composite for microbial filtration application’, Adv. Appl. Ceram., 2014, 113, 267–274. doi: 10.1179/1743676114Y.0000000162
9.
EsfahaniH., SalahiE., TayebifardA.RahimipourM. R. and Keyanpour-RadM.:‘Influence of zinc incorporation into non-stoichiometric hydroxyapatite on zeta potential’, Adv. Appl. Ceram., 2014, 113, 275–281. doi: 10.1179/1743676114Y.0000000163
10.
LiG., LiangG., ZhaoS.MaK.FengW.ZhouD. and LiuX.: ‘Synthesis and characterisation of porous luminescent glass ceramic scaffolds containing europium for bone tissue engineering’, Adv. Appl. Ceram., 2014, 114, 164–174. doi: 10.1179/1743676114Y.0000000210
11.
MondalB., MandalN., MondalS.MukherjeeK.MukhopadhyayS. and DeyA.: ‘Optimisation of process parameters for fabrication of nanocrystalline TiO2-hydoxyapatite based scaffold using response surface methodology’, Adv. Appl. Ceram., 2014, 113, 129–138. doi: 10.1179/1743676113Y.0000000126
RiceR. W., WuC. C. and BorcheltF.: ‘Hardness–grain-size relations in ceramics’, J. Am. Ceram. Soc., 1994, 77, 2539–2553. doi: 10.1111/j.1151-2916.1994.tb04641.x
