A solid-state and continuous groove repair technology was proposed for aluminium alloy based on friction rolling additive manufacturing (FRAM). The feasibility of FRAM was explored by repairing three types of prefabricated groove damages in aluminium alloy plates. A well-repaired joint for trapezoidal groove was obtained when the press-in depth of the tool head was 2 mm. The press-in depth was the key factor to complete filling of the groove damage. Effective grain refinement of the repair centre and the significant refinement area are observed, which leads to the hardness of these two areas reaching 99% and 102% of the substrate, respectively. The material migration behaviour of the filling material during the process was clarified.
LiS, DongHG, LiP, . Effect of repetitious non-isothermal heat treatment on corrosion behavior of Al-Zn-Mg alloy. Corros Sci. 2018;131:278–289.
2.
PerandiniJPB, BordinassiEC, BatalhaMHF, . Superficial residual stress, microstructure, and efficiency in similar joints of AA2024-T3 and AA7475-T761 aluminum alloys formed by friction stir welding. Int J Adv Manuf Tech. 2021;116:117–136.
3.
Stanzl-TscheggSE, MeischelM, ArcariA, . Combined cycle fatigue of 7075 aluminum alloy-fracture surface characterization and short crack propagation. Int J Fatigue. 2016;91:352–362.
4.
ChengQ, GuoN, FuYL, . Investigation on in-situ laser cladding 5356 aluminum alloy coating on 5052 aluminum alloy substrate in water environment. J Mater Res Technol. 2021;15:4343–4352.
5.
WangXY, WangJH, GaoZM, . Fabrication of graded surfacing layer for the repair of failed H13 mandrel using submerged arc welding technology. J Mater Process Technol. 2018;262:182–188.
6.
KashaevN, VentzkeV, ÇamG.Prospects of laser beam welding and friction stir welding processes for aluminum airframe structural applications. J Manuf Process. 2018;36:571–600.
7.
HanB, ChenYB, TaoW, . Nano-indentation investigation on the local softening of equiaxed zone in 2060-T8/2099-T83 aluminum-lithium alloys T-joints welded by double-sided laser beam welding. J Alloys Compd. 2018;756:145–162.
8.
AliakbariS, KetabchiM, MirsalehiSE.Effect of through-thickness friction stir processing parameters on weld repair and modification of fusion-welded AA6061 aluminum alloy. J Mater Eng Perform. 2019;28(5):2688–2696.
9.
HanB, HuangYX, LvSX, . AA7075 bit for repairing AA2219 keyhole by filling friction stir welding. Mater Des. 2013;51:25–33.
10.
IkumapayiOM, AkinlabiET.Recent advances in keyhole defects repairs via refilling friction stir spot welding. Mater Today: Proc. 2019;18:2201–2208.
11.
MetzDF, BarkeyME.Fatigue behavior of friction plug welds in 2195 Al-Li alloy. Int J Fatigue. 2012;43:178–187.
12.
PabandiHK, MovahediM, KokabiAH.A new refill friction spot welding process for aluminum/polymer composite hybrid structures. Compos Struct. 2017;174:59–69.
13.
JiSD, MengXC, MaL, . Vertical compensation friction stir welding assisted by external stationary shoulder. Mater Des. 2015;68:72–79.
14.
YinYY, YangXQ, CuiL, . Investigation on welding parameters and bonding characteristics of underwater wet friction taper plug welding for pipeline steel. Int J Adv Manuf Tech. 2015;81:851–861.
15.
UnfriedSJ, PaesMTP, HermenegildoTFC, . Study of microstructural evolution of friction taper plug welded joints of C-Mn steels. Sci Technol Weld Joining. 2010;15(6):506–513.
16.
YinY, YangX, CuiL, . Microstructure and mechanical properties of underwater friction taper plug weld on X65 steel with carbon and stainless steel plugs. Sci Technol Weld Joining. 2016;21(4):259–266.
17.
VicharapuB, KananLF, ClarkeT, . An investigation on friction hydro-pillar processing. Sci Technol Weld Joining. 2017;22(7):555–561.
18.
LandellR, KananLF, BuzzattiD, . Material flow during friction hydro-pillar processing. Sci Technol Weld Joining. 2020;25(3):228–234.
19.
AmaviscaCV, Cordenonsi da FonsecaG, DiehlIL, . Investigation of the residual stress distribution in repairs in H13 steel by friction hydro pillar processing. Sci Technol Weld Joining. 2020;25(6):503–510.
20.
XieRS, ShiYC, LiuHB, . A novel friction and rolling based solid-state additive manufacturing method: microstructure and mechanical properties evaluation. Mater Today Commun. 2021;29:103005.
21.
XieRS, LiangTS, ShiYC, . Revealing the bonding mechanisms between deposit and substrate of the friction rolling additive manufactured hybrid aluminum alloys. Addit Manuf. 2022;56:102942.
22.
HamiltonC, DymekS, BlicharskiM.A model of material flow during friction stir welding. Mater Charact. 2008;59(9):1206–1214.
23.
GriffithsRJ, PetersenDT, GarciaD, . Additive friction stir-enabled solid-state additive manufacturing for the repair of 7075 aluminum alloy. Appl Sci. 2019;9(17):3486.
24.
HuangK, LogéRE.A review of dynamic recrystallization phenomena in metallic materials. Mater Des. 2016;111:548–574.
25.
HallEO.The deformation and ageing of mild steel: III discussion of results. Proc Phys Soc. 1951;643(9):747–752.
26.
KaibyshevR, MusinF, GromovD, . Grain refinement and superplastic behaviour of a modified 6061 aluminium alloy. Mater Sci Technol. 2003;19(4):483–490.
27.
KalinenkoA, VysotskiyI, MalopheyevS, . Influence of the weld thermal cycle on the grain structure of friction-stir joined 6061 aluminum alloy. Mater Charact. 2021;178:111202.
