Friction welding (FW) enables joining of dissimilar metals parts up to the limits of their strength. CostE and NFA are two high-temperature steel alloys used in land-based power generation. These alloys were joined with FW, and the effect of process parameters on post-welded structure and tensile strength was studied. Weld energy primarily determined the heat-affected zone (HAZ) thickness in both alloys. The highest joint efficiencies – up to 96% – resulted from contact strengthening of thin NFA HAZ regions, but too thin of a HAZ resulted in an unreliable joint. Conversely, thick HAZ regions consistently lowered the weld strength. Optimal welding conditions occur with sufficient energy to create a full bond but not so much to notably lower weld strength.
KimuraM, ChojiM, KusakaM, Effect of friction welding conditions and aging treatment on mechanical properties of A7075-T6 aluminium alloy friction joints. Sci Technol Weld Joining. 2005; 10(4):406–412. doi:10.1179/174329305X44125.
5.
KumarD, VermaA, KulshresthaS, Microstructure and mechanical properties of mild steel copper joined by friction welding. Int J Mech Eng Technol. 2013; 4(5):295–300.
WorkmanGM, NicholasED.Friction welding aluminium and its alloys To various metals. Met Mater (Inst Met). 1986; 2(3):138–140.
9.
SahinM.Joining of aluminium and copper materials with friction welding. Int J Adv Manuf Technol. 2010; 49(5-8):527–534. doi:10.1007/s00170-009-2443-7. http://link.springer.com/10.1007/s00170-009-2443-7
Ahmad FauziMN, UdayMB, ZuhailawatiH, Microstructure and mechanical properties of alumina-6061 aluminium alloy joined by friction welding. Mater Des. 2010; 31(2):670–676. doi:10.1016/j.matdes.2009.08.019. https://www.sciencedirect.com/science/article/pii/S0261306909004427
12.
DiDomizioR, HuangS, DialL, An assessment of milling time on the structure and properties of a nanostructured ferritic alloy (NFA). Metall Mater Trans A. 2014; 45(12):5409–5418. doi:10.1007/s11661-014-2521-9.
MazumderB, YuX, EdmondsonPD, Effect of friction stir welding and post-weld heat treatment on a nanostructured ferritic alloy. J Nucl Mater. 2016; 469:200–208. doi:10.1016/j.jnucmat.2015.11.061.
15.
SketchleyPD, ThreadgillPL, WrightIG.Rotary friction welding of an Fe3Al based ODS alloy. Mater Sci Eng A. 2002; 329-331:756–762. doi:10.1016/S0921-5093(01)-01656-2.
16.
SekiM, HirakoK, KonoS, Pressurized resistance welding technology development in 9Cr-ODS martensitic steels. J Nucl Mater. 2004; 329-333(1-3 PART B):1534–1538. doi:10.1016/j.jnucmat.2004.04.172.
17.
DansieTS.Simulation of the Inertia friction welding process using a subscale specimen and a friction stir welder [Ph.D. Thesis], Brigham Young University (2018).
18.
ChambolleA, CasellesV, CremersD, An Introduction to Total Variation for Image Analysis. In: FornasierM.Theoretical Foundations and Numerical Methods for Sparse Recovery.: De Gruyter; 2010. p. 263–340.
19.
NowackiJ, SajekA, MatkowskiP.The influence of welding heat input on the microstructure of joints of S1100QL steel in one-pass welding. Arch Civil Mech Eng. 2016; 16(4):777–783. doi:10.1016/j.acme.2016.05.001.
