There is a synergy between welding and additive manufacturing with reference to spatial and temporal variations of heat transfer. In this research, in-situ measurements of heat transfer conditions are considered as a viable qualification methodology for additive manufacturing (AM). Infrared imaging (IR) was performed within a laser powder bed fusion (L-PBF) AM machine equipped with an IR camera. Infrared thermal signatures as a function of space and time, while processing Ti6Al4V and 316L stainless steel powders, were extracted and analysed. The analyses correlated the defect evolution at low- and high-heat input conditions to thermal decay and integrated intensities. The IR based results were validated by processing a 316L cylinder with engineered porosities and detecting the same with ground truth data from computed tomography.
DuttaB, BabuSS, JaredB.Science, technology and applications of metals in additive manufacturing. 1st ed., Elsevier; 2019.
2.
MadridJ, . A welding capability assessment method (WCAM) to support multidisciplinary design of aircraft structures. Int J Interact Des Manuf. 2018; 12:833–851.
YoderS, . Approach to qualification using E-PBF In-situ process monitoring in Ti-6Al-4V. Addit Manuf. 2019; 28:98–106.
9.
YoderS, . Characterization of topology optimized Ti-6Al-4V components using electron beam powder bed fusion. Addit Manuf. 2018; 19:184–196.
10.
MazumderJ.Design for metallic additive manufacturing machine with capability for ‘certify as you build’. Procedia CIRP. 2015; 36:187–192.
11.
PoppSR.Impact of solidification on tensile strength of CoCr2-LC in Selective Laser Melting [MS Thesis]. University of Tennessee, Knoxville, accessed from https://trace.tennessee.edu/utk_gradthes/3400; May 2015.
12.
ChandrasekarS, . Investigating the effect of metal powder recycling in Electron beam powder Bed fusion using process log data. Addit Manuf. 2020; 32:# 100994.
13.
HainesMP, . In-situ synthesis of oxides by reactive process atmospheres during L-PBF of stainless steel. Addit Manuf. 2020; 33:#101178.
14.
FengZ, ZachariaT, DavidSA.Thermal stress development in a nickel-based superalloy during weldability test. 1997; 76:470s-483s.
15.
ClijstersS, . In situ quality control of the selective laser melting process using a high-speed, real-time melt pool monitoring system. Int J Adv Manuf Technol. 2014; 75:1089–1101.
16.
HallAC, RobinoCV.Association of microstructural features and rippling phenomenon in 304 stainless steel gas tungsten arc welds. Sci Technol Weld Joining. 2004; 9:103–108.
17.
GrassoM, . In-process monitoring of selective laser melting: spatial detection of defects via image data analysis. J Manuf Sci Eng. 2017; 139:#051001.
18.
FurumotoT, . Monitoring of laser consolidation process of metal powder with high speed video camera. Phys Procedia. 2012; 39:760–766.
19.
FrederickC, . Geometry-induced spatial variation of microstructure evolution during selective electron beam melting of rene-N5. Metall Mater Trans A. 2018; 49:5080–5096.
20.
RapleeJ, . Thermographic microstructure monitoring in electron beam additive manufacturing. Sci Rep. 2017; 7:#43554.
21.
KraussH, . Layerwise monitoring of the selective laser melting process by thermography. Phys Procedia. 2014; 56:64–71.
22.
FosterSJ, . Process-defect-structure-property correlations during laser powder bed fusion of alloy 718: role of In Situ and Ex Situ characterizations. Metall Mater Trans A. 2018; 49:5775–5798.
23.
KoesterLW, ., Acoustic monitoring of additive manufacturing for damage and process condition determination, AIP Conference Processings, 2019, Vol. 2102, #020005.
24.
ShevchikSA, . Acoustic emission for in situ quality monitoring in additive manufacturing using spectral convolutional neural networks. Addit Manuf. 2018; 21:598–604.
25.
SetoN, . Porosity formation mechanism and suppression procedure in laser welding of aluminium alloys. Weld Int. 2001; 15:191–202.
26.
MohantyPS, MazumderJ.Solidification behavior and microstructural evolution during laser beam—material interaction. Metall Mater Trans B. 1998; 29:1269–1279.
27.
LednevVN, . In situ elemental analysis and failures detection during additive manufacturing process utilizing laser induced breakdown spectroscopy. Opt Express. 2019; 27: 4612. #347604.
28.
FosterDR, .
In situ velocity measurements of very high power ultrasonic additive manufacturing using a photonic Doppler velocimeter. Sci Technol Weld Join. 2014; 19:157–163.
29.
BaucherAB, . Defect characterization through automated laser track trace identification in SLM processes using laser profilometer data. J Mater Eng Perform. 2019; 28:717–727.
30.
PliazhukM, . In-situ monitoring of transient strain formation in vertical welds. Weld J. 2019; 98:251s–261s.
31.
EvertonSK, . Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing. Mater Des. 2016; 95:431–445.
32.
GaikwadA, . Towards the digital twin of additive manufacturing: integrating thermal simulations, sensing, and analytics to detect process faults. IISE Trans. 2020. DOI:10.1080/24725854.2019.1701753
GrassoM, ColosimoM.Process defects and in situ monitoring methods in metal powder bed fusion: a review. Meas Sci Technol. 2017; 28:#044005.
35.
BabuSS.Toward process-based quality through a fundamental understanding of weld microstructural evolution. Weld J. 2018; 97:1–16.
36.
SpearsTG, GoldSA.In-process sensing in selective laser melting (SLM) additive manufacturing. Integr Mater Manuf Innov. 2016; 5:16–40.
37.
CherryJA, . Investigation into the effect of process parameters on microstructural and physical properties of 316L stainless steel parts by selective laser melting. Int J Adv Manuf Technol. 2015; 76:869–879.
38.
RapleeJB.Monitoring the metal additive manufacturing process through thermographic data analyses. [MS Thesis]. University of Tennessee, Knoxville; 2017.
39.
LeeS-J, . Weldability and keyhole behavior of Zn-coated steel in remote welding using disk laser with scanner head. J Laser Appl. 2013; 25:#032008.
40.
CunninghamR, . Keyhole threshold and morphology in laser melting revealed by ultrahigh-speed X-ray imaging. Science. 2019; 363:849–852.
41.
TsukamotoS.High speed imaging technique Part 2 – High speed imaging of power beam welding phenomena. Sci Technol Weld Join. 2011; 16:44–55.
42.
PlotkowskiA, . Verification and validation of a rapid heat transfer calculation methodology for transient melt pool solidification conditions in powder bed metal additive manufacturing. Addit Manuf. 2017; 18:256–268.
43.
ASME Section IX; Welding, brazing and fusing qualifications; Qualification standard for welding, brazing, and fusing procedures; Welders; Brazers; and Welding, brazing and fusing operators. ASME Boiler and Pressure Vessel Code. New York: The American Society of Mechanical Engineers; 2013.
44.
BamfordWH, BushJA.Fracture behavior of stainless steel. In: LandesJD, BagleyJA, ClarkeGA, editors. Elastic-Plastic Fracture, ASTM STP 668. Philadelphia (PA): American Society for Testing and Materials; 1979. p. 553–577.
