In this study, an in-depth investigation of repair weld geometry effects on residual stress distributions in terms of both through-thickness membrane and bending content as well as its contribution to fracture driving force is carried out. Some major findings are: A fundamental difference in residual stress distributions between initial and repair welds can be characterised as a significant elevation of membrane and bending content in transverse residual stresses. The dominance of repair-induced residual stresses over those generated by initial welds suggests that initial weld residual stresses can be assumed negligible in repair weld modelling. A weld repair should be designed as long as possible, as narrow as possible and as shallow as possible.
GandyDW, FindlanSJ, ViswanathanR. Weld repair of steam turbine casings and piping – an industry survey. J Strain Anal.2000; 35(4):287–305. doi: 10.1243/0309324001514422
2.
GeorgeD, SmithDJ. Through thickness measurement of residual stresses in a stainless steel cylinder containing shallow and deep weld repairs. Int J Press Vessels Pip.2005; 82:279–287. doi: 10.1016/j.ijpvp.2004.08.006
3.
The Battelle integrity of nuclear piping (BINP) program final report – Appendix G: Evaluation of reactor pressure vessel (BPV) nozzle to hog-leg piping bimetallic weld joint integrity for the VC summer nuclear power plant report. 2005.
4.
BouchardPJ, GeorgeD, SantistebanJR, Measurement of the residual stress in a stainless steel pipe girth weld containing long and short repairs. Int J Press Vessels Pip.2005; 82:299–310. doi: 10.1016/j.ijpvp.2004.08.008
5.
DongP, ZhangJ, BouchardPJ. Effects of repair weld length on residual stress distribution. Trans ASME. 2002; 124:74–80. doi: 10.1115/1.1401455
6.
DongP, HongJK, ZhangJ, Effects of repair weld residual stresses on wide panel specimens loaded in tension. Trans ASME. 1998; 120:122–127.
7.
DongP, HongJK, RogersP. Analysis of residual stresses in Al-Li repair welds and mitigation techniques. Weld J.1998; 77(11):439–445.
8.
DongP, HongJK, BouchardPJ. Analysis of residual stresses at weld repairs. Int J Press Vessel Pip.2005; 82:258–269. doi: 10.1016/j.ijpvp.2004.08.004
9.
DongP, SongS. WRC Bulletin 553: Weld residual stress estimate for FFS assessment and evaluation of local PWHT procedures, The Welding Research Council, ISSN 2372-1057, July 2016, https://forengineers.org/bulletin/wrc-553
10.
KatsuyamaJ, MasakiK, OnizawaK. Effect of partial welding on the residual stress and structural integrity of piping welds. J Press Vessel Technol.2013; 135:8.
11.
JiangW, LuoY, WangB, Neutron diffraction measurement to study the effect of repair depth on residual stress in 316L stainless steel repair weld. J Press Vessel Technol.2015; 137:12.
12.
JiangW, LiuZ, GongJM, Numerical simulation to study the effect of repair width on residual stresses of a stainless steel clad plate. Int J Press Vessels Pip.2010; 87:457–463. doi: 10.1016/j.ijpvp.2010.06.003
13.
SongS, DongP. Residual stresses in weld repairs and mitigation by design, Proc. ASME 2014 OMAE Conf., OMAE2014-24547, San Francisco, CA, USA, 8–13 June 2014.
14.
DongP, HongJK. Analysis of IIW X/XV RSDP phase I round-robin residual stress results. Weld World. 2002; 46:24–31. doi: 10.1007/BF03263380
15.
DongP, SongS, ZhangJ, On residual stress prescriptions for fitness for service assessment of pipe girth welds. Int J Press Vessels Pip.2014; 123–124:19–29. doi: 10.1016/j.ijpvp.2014.07.006
16.
SongS, DongP, PeiX. A full-field residual stress estimation scheme for fitness-for-service assessment of pipe girth welds: part I: identification of key parameters. Int J Press Vessels Pip. 2015; 126–127:58–70. doi: 10.1016/j.ijpvp.2015.01.002
17.
SongS, DongP. A framework for estimating residual stress profile in seam-welded pipe and vessel components: part 1 – weld region. Int J Press Vessels Pip.2016; 146:74–86. doi: 10.1016/j.ijpvp.2016.07.009
18.
DongP, SongS, PeiX. A IIW residual stress estimation scheme for girth welds in pressure vessel and piping components. Weld World. 2016; 60(2):283–298. doi: 10.1007/s40194-015-0286-4
19.
DongP, SongS, ZhangJ. Analysis of residual stress relief mechanisms in post-weld heat treatment. Int J Press Vessels Pip.2014; 122:6–14. doi: 10.1016/j.ijpvp.2014.06.002
20.
DongP. On the mechanics of residual stresses in girth welds. J Press Vessel Technol. 2006; 129(3):345–354. doi: 10.1115/1.2748817
21.
SongS, PeiX, DongP. An analytical interpretation of welding linear heat input for 2D residual stress models. PVP2015-45753, Proc. ASME 2015 PVP Conf., Boston, MA, USA, 19–23 July 2015.
22.
BrustFW, DongP, ZhangJ. A constitute for welding process simulation using finite element methods. Advances in computational engineering science 1997, Proc. ICES Conf., 51–56.
23.
ABAQUS version 6.11. 2012.
24.
BPVC Section II Materials Part D Properties, ASME2015, ISBN: 9780791869789.
25.
ElcoateCD, DennisRJ, BouchardPJ, Three dimensional multi-pass repair weld simulations. Int J Press Vessels Pip.2005; 82:244–257. doi: 10.1016/j.ijpvp.2004.08.003
26.
DongP. Length scale of secondary stresses in fracture and fatigue. Int J Press Vessels Pip.2008; 85:128–143. doi: 10.1016/j.ijpvp.2007.10.005
27.
DongP, HongJK. Fracture mechanics treatment of residual stress in defect assessment. Weld World. 2004; 48:28–38.
