Ultrafine-grained (UFG) 2024 aluminium alloy prepared by the equal channel angular pressing was friction stir welded (FSW). The high cycle fatigue and crack growth behaviour of the FSW joint were investigated in air and NaCl solution, respectively. This study demonstrated that FSW was a viable technique for joining UFG materials. The UFG microstructure was retained in the nugget zone (NZ). Compared with the UFG base metal (BM), FSW joint exhibited lower ultimate tensile strength and hardness, and the minimum hardness value was located in the heat affected zone (HAZ). NaCl solution significantly reduced the fatigue strength of FSW joint. Fatigue crack propagation rates in the NZ and HAZ were slower than that in the BM in the whole fatigue life.
ValievR. Z., IslamgalievR. K. and AlexandrovI. V.: ‘Bulk nanostructured materials from severe plastic deformation’, Prog. Mater. Sci., 2000, 45, (2), 103–189. doi: 10.1016/S0079-6425(99)00007-9
2.
MishraR. S. and MaZ. Y.: ‘Friction stir welding and processing’, Mater. Sci. Eng. R, 2005, 50, (1–2), 1–78. doi: 10.1016/j.mser.2005.07.001
3.
SatoY. S., UrataM., KokawaH., IkedaK. and EnomotoM.: ‘Retention of fine grained microstructure of equal channel angular pressed aluminum alloy 1050 by friction stir welding’, Scripta Mater., 2001, 45, (1), 109–114. doi: 10.1016/S1359-6462(01)01000-4
4.
SatoY. S., KuriharaY., ParkS. H. C., KokawaH. and TsujiN.: ‘Friction stir welding of ultrafine grained Al alloy 1100 produced by accumulative roll-bonding’, Scripta Mater., 2004, 50, (1), 57–60. doi: 10.1016/j.scriptamat.2003.09.037
5.
TopicI., HöppelH. W. and GökenM.: ‘Friction stir welding of accumulative roll-bonded commercial-purity aluminium AA1050 and aluminium alloy AA6016’, Mater. Sci. Eng. A, 2009, 503, (1–2), 163–166. doi: 10.1016/j.msea.2007.12.057
6.
HosseiniM. and Danesh ManeshH.: ‘Immersed friction stir welding of ultrafine grained accumulative roll-bonded Al alloy’, Mater. Des., 2010, 31, (10), 4786–4791. doi: 10.1016/j.matdes.2010.05.007
7.
YuX., MazumderB., MillerM. K., DavidS. A. and FengZ.: ‘Stability of Y-Ti-O precipitates in friction stir welded nanostructured ferritic alloys’, Sci. Technol. Weld. Join., 2015, 20, (3), 236–241. doi: 10.1179/1362171815Y.0000000002
8.
SabooniS., KarimzadehF., EnayatiM. H. and NganA. H. W.: ‘Recrystallisation mechanism during friction stir welding of ultrafine- and coarse-grained AISI304L stainless steel’, Sci. Technol. Weld. Join., 2016, 21, (4), 287–294. doi: 10.1080/13621718.2015.1104097
9.
SatoY. S., UrataM., KokawaH. and IkedaK.: ‘Hall-Petch relationship in friction stir welds of equal channel angular-pressed aluminium alloys’, Mater. Sci. Eng. A, 2003, 354, (1–2), 298–305. doi: 10.1016/S0921-5093(03)00008-X
10.
SunY., FujiiH., TakadaY., TsujiN., NakataK. and NogiK.: ‘Effect of initial grain size on the joint properties of friction stir welded aluminum’, Mater. Sci. Eng. A, 2009, 527, (1–2), 317–321. doi: 10.1016/j.msea.2009.07.071
11.
SunY. F., FujiiH. and TsujiN.: ‘Microstructure and mechanical properties of spot friction stir welded ultrafine grained 1050 Al and conventional grained 6061-T6 Al alloys’, Mater. Sci. Eng. A, 2013, 585, 17–24. doi: 10.1016/j.msea.2013.07.030
12.
KamachiM., FurukawaM., HoritaZ. and LangdonT. G.: ‘Equal-channel angular pressing using plate samples’, Mater. Sci. Eng. A, 2003, 361, (1–2), 258–266. doi: 10.1016/S0921-5093(03)00522-7
13.
NazarovA. A., RomanovA. E. and ValievR. Z.: ‘On the structure, stress fields and energy of nonequilibrium grain boundaries’, Acta Metall. Mater., 1993, 41, (4), 1033–1040. doi: 10.1016/0956-7151(93)90152-I
14.
ColliganK.: ‘Material flow behavior during friction stir welding of aluminum’, Weld. J. (Miami Fla), 1999, 78, (7), S229–S237.
15.
ZhangH. J., LiuH. J. and YuL.: ‘Microstructural evolution and its effect on mechanical performance of joint in underwater friction stir welded 2219-T6 aluminium alloy’, Sci. Technol. Weld. Join., 2011, 16, (5), 459–464. doi: 10.1179/1362171811Y.0000000024
16.
WangK. S., WuJ. L., WangW., ZhouL. H., LinZ. X. and KongL.: ‘Underwater friction stir welding of ultrafine grained 2017 aluminum alloy’, J. Cent. South Univ., 2012, 19, (8), 2081–2085. doi: 10.1007/s11771-012-1248-2
17.
ZhouC. Z., YangX. Q. and LuanG. H.: ‘Fatigue properties of friction stir welds in Al 5083 alloy’, Scripta Mater., 2005, 53, (10), 1187–1191. doi: 10.1016/j.scriptamat.2005.07.016
18.
UematsuY., TokajiK., ShibataH., TozakiY. and OhmuneT.: ‘Fatigue behaviour of friction stir welds without neither welding flash nor flaw in several aluminium alloys’, Int. J. Fatigue, 2009, 31, (10), 1443–1453. doi: 10.1016/j.ijfatigue.2009.06.015
19.
CavaliereP.: ‘Fatigue properties and crack behavior of ultra-fine and nanocrystalline pure metals’, Int. J. Fatigue, 2009, 31, (10), 1476–1489. doi: 10.1016/j.ijfatigue.2009.05.004
20.
VinogradovA., NagasakiS., PatlanV., KitagawaK. and KawazoeM.: ‘Fatigue properties of 5056 Al-Mg alloy produced by equal-channel angular pressing’, Nanostruct. Mater., 1999, 11, (7), 925–934. doi: 10.1016/S0965-9773(99)00392-X
21.
SureshS., VasudévanA. K. and BretzP. E.: ‘Mechanisms of slow fatigue crack growth in high strength aluminium alloys: role of microstructure and environment’, Metall. Trans. A, 1984, 15, (2), 369–379. doi: 10.1007/BF02645122
22.
JohnR., JataK. V. and SadanandaK.: ‘Residual stress effects on near-threshold fatigue crack growth in friction stir welds in aerospace alloys’, Int. J. Fatigue, 2003, 25, (9–11), 939–948. doi: 10.1016/j.ijfatigue.2003.08.002
23.
PrimeM. B., Gnäupel-HeroldT., BaumannJ. A., LederichR. J., BowdenD. M. and SebringR. J.: ‘Residual stress measurements in a thick, dissimilar aluminum alloy friction stir weld’, Acta Mater., 2006, 54, (15), 4013–4021. doi: 10.1016/j.actamat.2006.04.034
24.
WooW., FengZ., WangX. L. and DavidS. A.: ‘Neutron diffraction measurements of residual stresses in friction stir welding: a review’, Sci. Technol. Weld. Join., 2011, 16, (1), 23–32. doi: 10.1179/136217110X12731414739916
25.
FratiniL., PastaS. and ReynoldsA. P.: ‘Fatigue crack growth in 2024-T351 friction stir welded joints: Longitudinal residual stress and microstructural effects’, Int. J. Fatigue, 2009, 31, (3), 495–500. doi: 10.1016/j.ijfatigue.2008.05.004
26.
PougetG. and ReynoldsA. P.: ‘Residual stress and microstructure effects on fatigue crack growth in AA2050 friction stir welds’, Int. J. Fatigue, 2008, 30, (3), 463–472. doi: 10.1016/j.ijfatigue.2007.04.016
27.
PaoP. S., GillS. J., FengC. R. and SankaranK. K.: ‘Corrosion-fatigue crack growth in friction stir welded Al 7050’, Scripta Mater., 2001, 45, (5), 605–612. doi: 10.1016/S1359-6462(01)01070-3
