Transient thermal and residual stress fields in flux-cored arc welds were examined using a finite element (FE) model. Experimental multipass welds were produced using both conventional and low transformation temperature (LTT) filler metals. Temperature-dependent material properties and both convective and radiant heat loss boundary condition have been considered in the FE model. The effects of the transformation temperature and interpass intervals on residual stresses were examined. It was found that compressive longitudinal residual stresses were developed at the weld centreline in the LTT filler metal. A short-time interpass interval causes the weld fusion zone to be above the martensite start temperature allowing the optimal use of the phase transformation effect. The FE model is sensitive to alteration in welding parameters and can satisfactorily predict the residual stress distribution in welded parts.
BhadeshiaH. K. D. H.: ‘Bainite in steels’, 2nd edn, Vol. 1, 240–249; 2001, London, Maney.
2.
GoldakJ. A. and AkhlaghiM.: ‘Computational welding mechanics’, 2005, London, Springer.
3.
NovotnýL. and TsunoriM.: ‘Creation of imperfections for welding simulations’, Comput. Model. Eng. Sci., 2011, 82, (3&4), 253–264.
4.
AlghamdiT. and LiuS.: ‘Low-transformation-temperature (LTT) welding consumables development and testing qualification’, Weld. J., 2014, 93, 243–252.
5.
AbreuH. F. G., TavaresW. S., MirandaH. C., FoncesaM. P. C., Virgens-NetoH. N. and BérešM.: ‘Effect of multipass welding using a low transformation temperature filler metal on residual stress and toughness’, Mater. Sci. Forum, 2014, 783–786, 627–632.
6.
EckerlidJ., NilssonT. and KarlssonL.: ‘Fatigue properties of longitudinal attach-ments welded using low transformation temperature filler’, Sci. Technol. Weld. Join., 2003, 8, 353–359.
7.
YamamotoJ., HiraokaK. and MochizukiM.: ‘Analysis of martensite transformation behaviour in welded joint using low transformation temperature welding wire’, Sci. Technol. Weld. Join., 2010, 15, (2), 104–110.
8.
XuL. Y., WangY. F., JingH. Y. and HanY. D.: ‘Fatigue strength improvement of stainless steel using weld toes dressing with low transformation temperature welding wire’, Sci. Technol. Weld. Join., 2014, 19, (8), 664–672.
9.
BérešM., AbreuH. F. G., SantosL. P. M., DaviesC. M. and DyeD.: ‘Effect of variant transformations in fusion zones of gas metal arc welds’, Sci. Technol. Weld. Join., 2015, 20, (4), 353–360.
10.
Payares-AsprinoM. C., KatsumotoH. and LiuS.: ‘Effect of martensite start and finish temperature on residual stress development in structural steel welds’, Weld. J., 2008, 87, 279–289.
11.
MoatR. J., StoneH. J., ShirzadiA. A., FrancisJ. A., KunduS., MarkA. F., BhadeshiaH. K. D. H., KarlssonL. and WithersP. J.: ‘Design of weld fillers for mitigation of residual stresses in ferritic and austenitic steel welds’, Sci. Technol. Weld. Join., 2011, 16, 279–284.
12.
ThomasS. H. and LiuS.: ‘Analysis of low transformation temperature welding (LTTW) consumables–distortion control and evolution of stresses’, Sci. Technol. Weld. Join., 2007, 12, (6), 516–522.
13.
ZenitaniS., HayakawaN., YamamotoJ., HiraokaK., MorikageY., KuboT., YasudaK. and AmanoK.: ‘Development of new low transformation temperature welding consumable to prevent cold cracking in high strength steel welds’, Sci. Technol. Weld. Join., 2014, 19, (5), 392–401.
14.
RamjaunT. I., StoneH. J., KarlssonL., KelleherJ., OoiS. W., DalaeiK., Rebelo KornmeierJ. and BhadeshiaH. K. D. H.: ‘Effects of dilution and baseplate strength on stress distributions in multipass welds deposited using low transformation temperature filler alloys’, Sci. Technol. Weld. Join., 2014, 19, (6), 461–467.
15.
RamjaunT. I., StoneH. J., KarlssonL., GharghouriM. A., DalaeiK., MoatR. J. and BhadeshiaH. K. D. H.: ‘Surface residual stresses in multipass welds produced using low transformation temperature filler alloys’, Sci. Technol. Weld. Join., 2014, 19, (7), 623–630.
16.
MikamiY., MorikageY., MochizukiM. and ToyodaM.: ‘Angular distortion of fillet welded T joint using low transformation temperature welding wire’, Sci. Technol. Weld. Join., 2009, 14, 97–105.
17.
ShirzadiA. A., BhadeshiaH. K. D. H., KarlssonL. and WithersP. J.: ‘Stainless steel weld metal designed to mitigate residual stresses’, Sci. Technol. Weld. Join., 2009, 14, (6), 559–565.
18.
DaiH., FrancisJ. A., StoneH. J., BhadeshiaH. K. D. H. and WithersP. J.: ‘Characterizing phase transformations and their effects on ferritic weld residual stresses with x-rays and neutrons’, Metall. Mater. Trans. A, 2008, 39, (13), 3070–3078.
19.
CenigaL.: ‘A new analytical model for thermal stresses in multi-phase materials and lifetime prediction methods’, Acta Mech. Sinica, 2008, 24, 189–206.
20.
LeoveanuI. S., and ZguraG.: ‘Modelling the heat and fluid flow in the welded pool from high power arc sources’, Mater. Sci. Forum,2008, 580–582, 443–446.
21.
ColegroveP., IkeaguC., ThistlethwaiteA., WilliamsS., NagyT., SuderW., SteuwerA. and PirlingT.: ‘Welding process impact on residual stress and distortion’, Sci. Technol. Weld. Join., 2009, 14, (8), 717–725.
22.
ColegroveP., ShercliffH. and ZettlerR.: ‘Model for predicting heat generation and temperature in friction stir welding from the material properties’, Sci. Technol. Weld. Join., 2007, 12, (4), 284–297.
23.
NovotnýL. and IvančoV.: ‘Calculations of phase transformations in welding simulations’, Appl. Mech. Mater., 2014, 611, 46–53.
24.
AndradeR. V.: ‘Pipe circularity reformation via line heating’, 2001, Cambridge, MA, Massachusetts Institute of Technology.
25.
PaponP., LeblondJ. and MeijerP. H. E.: ‘The physics of phase transitions–concepts and applications’, 2006, Berlin, Springer.
26.
MurakawaH., BérešM., DaviesC., RashedS., VegaA., TsunoriM., NikbinK. and DayD.: ‘The effect of low transformation temperature weld filler metal on welding residual stress’, Sci. Technol. Weld. Join., 2010, 15, (5), 393–399.
27.
FrouzanM. R., MirfalahS. M., MokhtariA., HeidariA. and GolestanehS. J.: ‘Residual stress prediction in submerged arc welded spiral pipes’, Mater. Des., 2012, 33, 384–394.
28.
JungM., KangM. and LeeY. K.: ‘Finite-element simulation of quenching incorporating improved transformation kinetics in a plain medium-carbon steel’, Acta Mater., 2012, 60, 525–536.
29.
OhtaA., WatanabeO., MatsuokaK., ShigaT., NishijimaS., MaedaY., SuzukiN. and KuboT.: ‘Fatigue strength improvement by using newly developed low transformation temperature welding material’, Weld. World, 1999, 43, 38–42.
30.
RamjaunT. I., StoneH. J., KarlssonL., KelleherJ., MoatR. J., KornmeierJ. R., DalaeiK. and BhadeshiaH. K. D. H.: ‘The effect of interpass temperature on residual stresses in multi-pass welds produced using a low transformation temperature filler alloy’, Sci. Technol. Weld. Join., 2014, 19, 44–51.
