Potential utilization of hazardous mining wastes in the production of lightweight aggregates

Abstract

Lightweight aggregates from mixtures of gold tailing, red mud and waste limestone were produced using a high-temperature sintering process. Raw materials were quantitatively analyzed, and hazardous materials were identified by chemical analysis. An oxide system corresponding to the major components of the mining waste was carefully designed based on the CaO–FeO _x –Al₂O₃–SiO₂ quaternary system similar to lightweight aggregates. Sintering, softening and melting behaviour of the sample was investigated to optimize the sintering conditions. After heating, specimens were analyzed to clarify its sintering mechanism. Phase change during sintering was observed by X-ray diffraction, and the effect of temperature on the structural unit changes of the specimen was confirmed by Fourier transform-infrared spectroscopy. Microscopic analysis by scanning electron microscope-energy dispersive X-ray analysis was carried out to identify the morphological changes of the sample. Physical properties of the specimen were measured, and the compressive strength was improved with less water absorption.

Keywords

Industrial waste materials lightweight aggregate gold tailing red mud limestone sintering fayalite physical property

Get full access to this article

View all access options for this article.

References

ASTM. 2016. Method C330: Standard Specification for Lightweight Aggregates for Structural Concrete. Available from: https://www.astm.org/Standards/C330.htm

Biswas

AK.

1981. Principles of blast furnace ironmaking: theory and practice. Brisbane: Cootha; p. 329.

Chandra

, Berntsson

2002. Lightweight aggregate concrete. London: Elsevier Science; p. 141.

Cheeseman

, Makinde

, Bethanis

2005. Properties of lightweight aggregate produced by rapid sintering of incinerator bottom ash. Resour Conserv Recycl. 43:147–162. doi: 10.1016/j.resconrec.2004.05.004

Deo

, Boom

1993. Fundamentals of steelmaking metallurgy. New York (NY): Prentice Hall International; p. 161–188.

Gaskell DR.

2003. Introduction to the thermodynamics of materials. 5th ed. New York (NY): Taylor & Francis; p. 582.

Klauber

, Grfe

, Power

2011. Bauxite residue issues: II. Options for residue utilization. Hydrometallurgy. 108:11–32. doi: 10.1016/j.hydromet.2011.02.007

Kubaschewski

, Alcock

, Spencer

PJ.

1993. Materials thermochemistry. London: Pergamon Press.

Mysen

, Richet

2005. Silicate glasses and melts: properties and structure. Amsterdam: Elsevier; p. 101–129.

10.

Park

, Kim

S-K

, Shin

, Sohn

J-S.

2016. Production of lightweight aggregate and ceramic balls by utilizing gold tailing, red mud and limestone. In: TMS. REWAS 2016. Nashville, TN: TMS.

11.

Park

, Kim

, Sohn

2011b. Influence of CaF₂ and Li₂O on the viscous behavior of calcium silicate melts containing 12 wt pct Na₂O. Metall Mater Trans. B. 42:324–330. doi: 10.1007/s11663-011-9474-9

12.

Park

, Park

, Kim

, Sohn

2012. Effect of TiO₂ on the viscosity and slag structure in blast furnace type slags. Steel Res Int. 83:150–156. doi: 10.1002/srin.201100249

13.

Park

H-S

, Park

, Sohn

2011a. The viscous behavior of FeOt–Al₂O₃–SiO₂ copper smelting slags. Metall Mater Trans. B. 42:692–699.

14.

Power

, Grfe

, Klauber

2011. Bauxite residue issues: I. Current management, disposal and storage practices. Hydrometallurgy. 108:33–45. doi: 10.1016/j.hydromet.2011.02.006

15.

Rahaman

2007. Sintering of ceramics. Boca Raton (FL): CRC Press; p. 182–187.

16.

Ritcey

GM.

2005. Tailings management in gold plants. Hydrometallurgy. 78:3–20. doi: 10.1016/j.hydromet.2005.01.001

17.

Siddique

2007. Waste materials and by-products in concrete (engineering materials). New York (NY): Springer; p. 297.

18.

Slag Atlas. 2005. Verlag Stahleisen, Dusseldorf.

19.

USEPA. 1992. Method 7196A: chromium, hexavalent (colorimetric). Available from: https://www.epa.gov/sites/production/files/2015-12/documents/7196a.pdf

20.

USEPA. 1996. Method 3060 A: alkaline digestion for hexavalent chromium. Available from: https://www.epa.gov/sites/production/files/2015-12/documents/3060a.pdf

21.

Waseda

, Toguri

JM.

1998. The structure and properties of oxide melts: application of basic science to metallurgical processing. Singapore: World Scientific; p. 67–106.

22.

Yashima

, Kanda

, Sano

1987. Relationships between particle size and fracture energy or impact velocity required to fracture as estimated from single particle crushing. Powder Technol. 51:277–282. doi: 10.1016/0032-5910(87)80030-X