The compression deformation behavior of AISI H10 (DIN 32CrMoV12-28) hot work tool steel was investigated at temperatures ranging from 900°C to 1200°C and strain rates from 0.01 to 1 s−1. True stress-strain curves showed that a decrease in strain rate or increase in deformation temperature can promote the occurrence of DRX. It was found that the characteristic strains and stresses decrease with an increase in temperature or decrease in strain rate. The σc/σp ratio takes an average of 0.94; and the ϵc/ϵp ratio lies in range of 0.48-0.65 (average of 0.53). This suggests that DRV in H10 is not extensive and DRX starts at strains about half of the peak strain. However, the extensive softening by DRX keeps σp close to σc. Using the hyperbolic-sine constitutive equation, the deformation activation energy was calculated to be about 435.76 kJ mol−1.
Get full access to this article
View all access options for this article.
References
1.
EbrahimiRSolhjouS.Characteristic points of stress-strain curve at high temperature. Int J Iron Steel Soc Iran. 2007;4:24–27.
2.
EbrahimiGRKeshmiriHMaldarARet al.Dynamic recrystallization behavior of 13%Cr martensitic stainless steel under hot working condition. J Mater Sci Technol. 2012;28:467–473.
3.
PoliakEIJonasJJ.A one-parameter approach to determining the critical conditions for the initiation of dynamic recrystallization. Acta Mater. 1996;44:127–136.
4.
PoliakEIJonasJJ.Initiation of dynamic recrystallization in constant strain rate hot deformation. ISIJ Int. 2003;43:684–691.
5.
SolhjooS.Determination of critical strain for initiation of dynamic recrystallization. Mater Des. 2010;31:1360–1364.
6.
EskandariMZarei-hanzakiAMarandiA.An investigation into the mechanical behavior of a new transformation-twinning induced plasticity steel. Mater Des. 2012;39:279–284.
7.
StewartGRJonasJJMontheilletF.Kinetics and critical conditions for the initiation of dynamic recrystallization in 304 stainless steel. ISIJ Int. 2004;44:1581–1589.
8.
JonasJJPoliakEI.The Critical Strain for Dynamic Recrystallization in Rolling Mills, Materials Science Forum. 2003;426(1):57–66.
9.
PoliakEIJonasJJ.Critical Strain for Dynamic Recrystallization in variable strain rate Hot deformation. ISIJ Int. 2003;43:692–700.
10.
NajafizadehAJonasJJ.Predicting the critical stress for initiation of dynamic recrystallization. ISIJ Int. 2006;46:1679–1684.
11.
Dehghan-ManshadiABarnetMRHodgsonPD.Hot deformation and recrystallization of austenitic stainless steel: part I. dynamic recrystallization. Metall Mater Trans A. 2008;39A:1359–1370.
12.
Jorge JuniorAMBalancinO.Prediction of steel flow stresses under hot working conditions. Mater Res. 2005;8:309–315.
13.
WuSTFengWHuX.Constitutive modelling of flow behaviour of 20CrMnTiH steel. Ironmak Steelmak. 2015;42:481–488.
14.
HuiLMeiXZhutieLet al.Hot deformation behaviour and processing map of a typical Fe-Mn-Si-Cr steel for automotive body structures. Ironmak Steelmak. 2017;45:1–7.
15.
ZuriñeALeireMIñakiPet al.Failure assessment in a H10 hot die forging tool related to thermal fatigue. Brno Czech Republic EU. 2015;5:1–6.
16.
OkunoT.Effect of microstructure on the toughness of hot work tool steels, AISI H13, H10, and H19. Trans Iron Steel Inst Jpn. 1987;27:51–59.
17.
PantMBleckW.Continuous impact wear resistance of duplex surface-modified hot work tool steel H10. Wear. 2005;259:377–382.
18.
Kamali ArdakaniMMorakabatiM.The effects of temperature and strain rate on the hot deformation behavior of AISI H10 tool steel”. Metall Res Technol. 2021;118(107.
19.
ShabanMEghbaliB.Determination of critical conditions for dynamic recrystallization of a microalloyed steel. Mater Sci Eng A. 2010;527(527):4320–4325.
20.
PerdrixCh, Caractéristiques d'écoulement plastique du métal dans les conditions du TAB à Chaud. Commission des Communautés européennes. 1982:58–74.
21.
StewartGRElwazriAMYueSet al.Modelling of dynamic recrystallisation kinetics in austenitic stainless and hypereutectoid steels. Mater Sci Technol. 2006;22:519–524.
22.
MejíaIBedolla-JacuindeAMaldonadoCet al.Determination of the critical conditions for the initiation of dynamic recrystallization in boron microalloyed steels. Mater Sci Eng A. 2011;528:4133–4140.
23.
HamtaeiSZarei-HanzakiAMohamadizadehA.Optimum deformation criteria and flow behavior description of boron-alloyed steel through numerical approach. Steel Res Int. 2016;87:1657–1669.
24.
WuHWenSPHuangHet al.Hot deformation behavior and constitutive equation of a new type Al–Zn–Mg–Er–Zr alloy during isothermal compression. Mater Sci Eng A. 2016;651:415–424.
25.
LiuJChangHWuRet al.Investigation on hot deformation behavior of AISI T1 high-speed steel. Mater Charact. 2000;45:175.
26.
RodenburgCKrzyzanowskiMBeynonJHet al.Hot workability of spray-formed AISI M3:2 high-speed steel. Mater Sci Eng A. 2004;386:420–427.
27.
ImbertCACMcQueenHJ.Peak strength, strain hardening and dynamic restoration of A2 and M2 tool steels in hot deformation. Mater Sci Eng A. 2001;313:88–103.
28.
ImbertCACMcQueenHJ.Dynamic recrystallization of D2 and W1 tool steels. Mater Sci Technol. 2000;16:524–531.
29.
McQueenHJRyanND.Constitutive analysis in hot working. Mater Sci Eng A. 2002;322(43).
30.
Bao-ShengXQing-WuCWeiYet al.Prediction for flow stress of 95CrMo hollow steel during Hot compression. Acta Metall Sin. 2017;30:250–260.
