Microstructure and mechanical properties of a medium-carbon bainitic steel treated by quenching and two-step bainitic isothermal transformation below Ms
Restricted accessResearch articleFirst published online March, 2022
Microstructure and mechanical properties of a medium-carbon bainitic steel treated by quenching and two-step bainitic isothermal transformation below Ms
A quenching and two-step bainitic isothermal transformation below Ms (Q-2BT) process was proposed for a medium-carbon steel. The evolution of microstructure and its correlation with mechanical properties were investigated and compared with the samples subjected to a quenching and one-step bainitic isothermal transformation below Ms (Q-1BT) process. Results showed that the Q-2BT sample has a finer martensite/bainite/retained austenite multiphase microstructure than the Q-1BT ones because of the formation of smaller bainite and the decomposition of large untransformed austenite blocks. Meanwhile, an optimal strength (1582 MPa), elongation (20.2%) and toughness (110 J) combination can be obtained after the Q-2BT process. The significantly improved impact toughness can be attributed to refined microstructure, increased filmy retained austenite as well as a high proportion of high-angle boundaries (70.7%). In addition, the Q-2BT sample exhibits a longer hardening plateau and a higher hardening exponent (0.084) because of the larger amount of retained austenite (11.3%) and more filmy austenite with high stability.
Get full access to this article
View all access options for this article.
References
1.
AnXGLiuYYeJWet al.Fabrication of in-situ TiC-TiB2 reinforced Al foam with enhanced properties. J Alloys Compd. 2020;825.
2.
LiQGZhangYNZhangYNet al.Influence of Sn and Nb additions on the microstructure and wear characteristics of a gray cast iron. Appl Phys a-Mater. 2020;126(4.
3.
SpeerJMatlockDKDe CoomanBCet al.Carbon partitioning into austenite after martensite transformation. Acta Mater. 2003;51(9):2611–2622.
4.
GaoGHZhangHGuiXLet al.Enhanced ductility and toughness in an ultrahigh-strength Mn-Si-Cr-C steel: The great potential of ultrafine filmy retained austenite. Acta Mater. 2014;76:425–433.
5.
HajyAkbaryFSietsmaJMiyamotoGet al.Interaction of carbon partitioning, carbide precipitation and bainite formation during the Q&P process in a low C steel. Acta Mater. 2016;104:72–83.
6.
HuangXFLiuWLHuangYYet al.Effect of a quenching-long partitioning treatment on the microstructure and mechanical properties of a 0.2C% bainitic steel. J Mater Process Tech. 2015;222:181–187.
7.
LiQGHuangXFHuangWG.Microstructure and mechanical properties of a medium-carbon bainitic steel by a novel quenching and dynamic partitioning (Q-DP) process. Mat Sci Eng A – Struct. 2016;662:129–135.
8.
HuangYYLiQGHuangXFet al.Effect of bainitic isothermal transformation plus Q & P process on the microstructure and mechanical properties of 0.2C bainitic steel. Mat Sci Eng A – Struct. 2016;678:339–346.
9.
SinghSBBhadeshiaHKDH.Estimation of bainite plate-thickness in low-alloy steels. Mat Sci Eng A – Struct. 1998;245(1):72–79.
10.
BhadeshiaHKDH.Bainite in steels: transformation, microstructure and properties, second edition ed. London: IOM Communications; 2001.
11.
ZhaoLQianLHMengJYet al. Below-Ms austempering to obtain refined bainitic structure and enhanced mechanical properties in low-C high-Si/Al steels, scripta Materialia 112 (2016) 96–100.
12.
WangKKTanZLGaoGHet al.Microstructure-property relationship in bainitic steel: The effect of austempering. Mat Sci Eng A – Struct. 2016;675:120–127.
13.
XiaSLZhangFCYangZN.Microstructure and mechanical properties of 18Mn3Si2CrMo steel subjected to austempering at different temperatures below Ms. Mat Sci Eng A – Struct. 2018;724:103–111.
14.
LacroixGPardoenTJacquesPJ.The fracture toughness of TRIP-assisted multiphase steels. Acta Mater. 2008;56(15):3900–3913.
15.
LiQGHuangXFHuangWG.Strain hardening hardening behavior and deformation characteristics of multiphase microstructure. Mat Sci Eng A – Struct. 2017;707:199–206.
16.
LiYLiWLiuWQet al.The austenite reversion and co-precipitation behavior of an ultra-low carbon medium manganese quenching-partitioning-tempering steel. Acta Mater. 2018;146:126–141.
17.
TianJYXuGJiangZYet al.Transformation behavior of bainite during Two-step isothermal process in an ultrafine bainite steel. ISIJ Int. 2018;58(10):1875–1882.
18.
AvishanBTavakolianMYazdaniS.Two-step austempering of high performance steel with nanoscale microstructure. Mat Sci Eng A – Struct. 2017;693:178–185.
SaeglitzMKraussG.Deformation, fracture, and mechanical properties of low-temperature-tempered martensite in SAE 43xx steels. Metall Mater Trans A. 1997;28(2):377–387.
21.
LiQGHuangXFHuangWG.EBSD analysis of relationship between Microstructural features and toughness of a medium-carbon quenching and partitioning bainitic steel. J Mater Eng Perform. 2017;26(12):6149–6157.
22.
YoozbashiMNYazdaniSWangTS.Design of a new nanostructured, high-Si bainitic steel with lower cost production. Mater Des. 2011;32(6):3248–3253.
23.
RaviAMNavarro-LopezASietsmaJet al.Influence of martensite/austenite interfaces on bainite formation in low-alloy steels below M-s. Acta Mater. 2020;188:394–405.
24.
GongWTomotaYHarjoSet al.Effect of prior martensite on bainite transformation in nanobainite steel. Acta Mater. 2015;85:243–249.
25.
Navarro-LópezAHidalgoJSietsmaMJ.Santofimia, influence of the prior athermal martensite on the mechanical response of advanced bainitic steel. Mat Sci Eng A – Struct. 2018;735:343–353.
26.
SuCHLiQGHuangXFet al.Effect of bainite microstructure during two-step quenching and partitioning process on strength and toughness properties of a 0.3%C bainitic steel. J Iron Steel Res Int. 2018;25(2):235–242.
27.
LiQGHuangXFHuangWG.Fatigue property and microstructure deformation behavior of multiphase microstructure in a medium-carbon bainite steel under rolling contact condition. Int J Fatigue. 2019;125:381–393.
28.
YanKLissKDTimokhinaIBet al.In situ synchrotron X-ray diffraction studies of the effect of microstructure on tensile behavior and retained austenite stability of thermo-mechanically processed transformation induced plasticity steel. Mat Sci Eng A – Struct. 2016;662:185–197.
29.
LiuEZLiQGNaseemSet al.Effect of isothermal transformation times below Ms and tempering on strength and toughness of Low-temperature bainite in 0.53 C bainitic steel. Materials (Basel). 2020;13(10.
30.
HuangJNTangZYDingHet al.Combining a novel cyclic pre-quenching and two-stage heat treatment in a low-alloyed TRIP-aided steel to significantly enhance mechanical properties through microstructural refinement. Mat Sci Eng A – Struct; 764(2019.
31.
LiQGZhangYALiWDet al.Improved mechanical properties of a quenched and partitioned medium-carbon bainitic steel by control of bainitic isothermal transformation (vol 29, pg 32, 2020). J Mater Eng Perform. 2020;29(4):2738–2738.
32.
RastegariHKermanpurANajafizadehA.Effect of initial microstructure on the work hardening behavior of plain eutectoid steel. Mat Sci Eng A – Struct. 2015;632:103–109.
