The high-temperature deformation behaviours of low carbon steel QD08 were investigated by hot compression tests over temperatures from 1000 to 1200°C and strain rates from 0.1 to 10 s−1. The processing map was obtained by superimposition of the power dissipation and the instability maps and the regions having the lowest strain rate sensitivity added for more clarification of low and high workability regions. The results show that the security domain mainly of hot deformation with a higher powder dissipation factor and maintain a smooth variation, by the metallographic observations, the grain refinement by DRX under the stable deformation conditions. On the basis of processing map and microstructure evolution, the optimal deformation processing parameters are the hot deformation temperature range from 1070 to 1100°C, and strain rates range from 5 to 10 s−1.
Get full access to this article
View all access options for this article.
References
1.
WenDXLinYCLiHBet al.Hot deformation behavior and processing map of a typical Ni-based superalloy. Mater Sci Eng A. 2014;591(2):183–192. doi: 10.1016/j.msea.2013.09.049
2.
ChengLChangHTangBet al.Deformation and dynamic recrystallization behavior of a high Nb containing TiAl alloy. J Alloys Compd. 2013;552(9):363–369. doi: 10.1016/j.jallcom.2012.11.076
3.
Hasan NasabMSerajzadehSet al.Thermal stresses and kinetics of phase transformation on the run-out table after hot strip rolling of low-carbon steels. Int J Adv Manuf Technol. 2016;83(9):1725–1736. doi: 10.1007/s00170-015-7604-2
4.
PrasadYVRKGegelHLDoraiveluSMet al.Modeling of dynamic material behavior in hot deformation: forging of Ti-6242. Metall Mater Trans A. 1984;15(10):1883–1892. doi: 10.1007/BF02664902
5.
MurtySVSNTorizukaSNagaiK.Microstructural evolution during simple heavy warm compression of a low carbon steel: development of a processing map. Mater Sci Eng A. 2005;410–411(12):319–323. doi: 10.1016/j.msea.2005.08.173
6.
YangZNZhangFCZhengCLet al.Study on hot deformation behaviour and processing maps of low carbon bainitic steel. Mater Des. 2015;66:258–266. doi: 10.1016/j.matdes.2014.10.068
7.
RajputSKChaudhariGPNathSK.Physical simulation of hot deformation of low-carbon Ti-Nb microalloyed steel and microstructural studies. J Mater Eng Perform. 2014;23(8):2930–2942. doi: 10.1007/s11665-014-1059-8
8.
RajputSKChaudhariGPNathSK.Characterization of hot deformation behavior of a low carbon steel using processing maps, constitutive equations and Zener-Hollomon parameter. J Mater Process Technol.2016;237:113–125. doi: 10.1016/j.jmatprotec.2016.06.008
9.
XiangSTanZL.Microstructure evolution and processing map of thermal deformation of Q690 low carbon microalloyed steel. J Hunan U Nat Sci.2013;40(4):80–86.
10.
XiangSLiuGQ.Processing map and its application of Nb-V-Ti low carbon microalloyed steel. Mater Sci Technol.2011;19(1):26–31.
11.
YangXWLiWY.Flow behavior and processing maps of a low-carbon steel during hot deformation. Metall Mater Trans A. 2015;46(12):6052–6064. doi: 10.1007/s11661-015-3190-z
12.
KangYXCaiDYZhangCLet al.Hot deformation equation and processing map of a micro-carbon steel. T Mater Heat Treat. 2012;33(6):47–50.
13.
DongHFCaiDYWangYHet al.Hot deformation behavior of Cr micro-alloyed low carbon steel. T Mater Heat Treat. 2009;30(6):47–50.
14.
LiuSClenetSCoorevitsTet al.Influence of the stator deformation on the behaviour of a claw-pole generator. IEEE T Magn.2016;52(3):1–4.
15.
BozziniBCerriE.Numerical reliability of hot working processing maps. Mater Sci Eng A. 2002;328(1):344–347. doi: 10.1016/S0921-5093(01)01686-0
16.
BabuKAMandalSKumarAet al.Characterization of hot deformation behavior of alloy 617 through kinetic analysis, dynamic material modeling and microstructural studies. Mater Sci Eng A. 2016;664:177–187. doi: 10.1016/j.msea.2016.04.004
17.
MilitzerM.Computer simulation of micro structure evolution in low carbon sheet steels. ISIJ Int. 2007;47(1):1–15. doi: 10.2355/isijinternational.47.1
18.
LiuHPLiuBLiDZet al.Hot deformation behavior of low carbon steel during compression at elevated temperature. J Wuhan U Tech-Mater Sci.2014;29(3):601–605. doi: 10.1007/s11595-014-0964-x
19.
LiSQLiuJHLiuHBet al.2017. Study on high-temperature mechanical properties of low-carbon Fe-Mn-Si-Al TWIP steel (https://doi.org/10.1515/htmp-2015-0144).
20.
MirzaieTMirzadehHCabreraJM.A simple Zerilli–Armstrong constitutive equation for modeling and prediction of hot deformation flow stress of steels. Mech Mater. 2016;94:38–45. doi: 10.1016/j.mechmat.2015.11.013
