This work focus on the influence of Ni-Coated Graphite contents on microstructure and properties of Al–Zn composite coatings. The morphology and composition of the coatings were analysed by SEM and EDS. The result showed that the coating is dense, the composition is uniform, and there is no phase change. The bonding mechanism between coating particles and between coating and substrate was also analysed. The hardness and wear resistance of the four coatings were tested. It was found that the addition of Ni-Coated Graphite improves the hardness and wear resistance of the coating. In general, the addition of 20% Ni-Coated Graphite powder is the best for Al–Zn composite coatings with low porosity.
LuX, WangS, XiongT, Anticorrosion properties of Zn-Al composite coating prepared by cold spraying. Coatings. 2019;9(3):210–220. doi: 10.3390/coatings9030210
3.
CervantesJ, BarbaA, HernandezMA, Development of Zn-Al-Cu coatings by hot dip coated technology: preparation and characterization. Revista de metalurgia. 2013;49(5):351–359. doi: 10.3989/revmetalm.1316
4.
BaiY, WangZ, LiX, Microstructure and mechanical properties of Zn-Ni-Al₂O₃ composite coatings. Materials (Basel). 2018;11(5):853–867. doi: 10.3390/ma11050853
5.
WangX, ChenY, YuC, Preparation and application of ZrC-coated flake graphite for Al2O3-C refractories. J Alloys Compd. 2019;788:739–747. doi: 10.1016/j.jallcom.2019.02.239
6.
HernandezMA, BakoglidisKD, XiaoP.A new slurry infiltration method to enhance the wear resistance of bulk graphite with development of reinforced graphitic composites including SiC or Si3N4 hard particles. J Eur Ceram Soc. 2019;39(6):1984–1992. doi: 10.1016/j.jeurceramsoc.2019.01.053
7.
ChenJ, ZhangQ, HouZ, Preparation and characterization of graphite/thermosetting composites. Bull Mater Sci. 2019;42(4):153–157. doi: 10.1007/s12034-019-1844-y
8.
HariharasakthisudhanP, MoshiAAM, BharathiSRS, Regression and grey relational analysis on friction and wear behavior of AA6061/Al2O3/Si3N4/ graphite hybrid nano composites. Mater Res Express. 2019;6(8):5017–5030. doi: 10.1088/2053-1591/ab1cd3
9.
KocR, OzkececiS.The fabrication of exfoliated graphite sheet-based air cathodes and gel electrolyte for metal-air batteries. Energy Sources, Part A: Recovery, Utilization, Environ Effects. 2019;41(14):1780–1790. doi: 10.1080/15567036.2018.1549154
10.
Sánchez EgeaAJ, MartynenkoV, AbateG, Friction capabilities of graphite-based lubricants at room and over 1400 K temperatures. Int J Adv Manuf Technol. 2019;102(5):1623–1633. doi: 10.1007/s00170-019-03290-4
11.
HuangC, LiW, XieY, Effect of substrate type on deposition behavior and wear performance of Ni-coated graphite/Al composite coatings deposited by cold spraying. J Mater Sci Technol. 2017;33(4):338–346. doi: 10.1016/j.jmst.2016.11.016
12.
DengN, TangJ, XiongT, Fabrication and characterization of W-Cu composite coatings with different W contents by cold spraying. Surf Coat Technol. 2019;368:8–14. doi: 10.1016/j.surfcoat.2019.04.034
13.
MachetheKE, PopoolabAPI, AdebiyiDI, Influence of SiC-Ti/Al on the microstructural and mechanical properties of deposited Ti-6V-4A1 alloy with cold spray technique. Procedia Manuf. 2017;7:549–555. doi: 10.1016/j.promfg.2016.12.069
14.
KoivuluotoH, ColemanA, MurrayK, High pressure cold sprayed (HPCS) and low pressure cold sprayed (LPCS) coatings prepared from OFHC Cu feedstock: overview from powder characteristics to coating properties. J Therm Spray Technol. 2012;21(5):1065–1075. doi: 10.1007/s11666-012-9790-x
15.
XieX, ChenC, XieY, Comparative investigation of microstructure and properties of Ni-coated FeSiAl soft magnetic composite coatings produced by cold spraying and HVOF. Surf Coat Technol. 2018;371:224–234. doi: 10.1016/j.surfcoat.2018.12.067
16.
TariqNU, GyansahL, QiuX, Achieving strength-ductility synergy in cold spray additively manufactured Al/B4C composites through a hybrid post-deposition treatment. J Mater Sci Technol. 2019;35(6):1053–1063. doi: 10.1016/j.jmst.2018.12.022
17.
YinS, LiW, SongB, Deposition of FeCoNiCrMn high entropy alloy (HEA) coating via cold spraying. J Mater Sci Technol. 2019;35(6):1003–1007. doi: 10.1016/j.jmst.2018.12.015
18.
ShahaSK, DayaniSB, XueYN, Improving corrosion and corrosion-fatigue resistance of AZ31B Cast Mg alloy using combined cold spray and top coatings. Coatings. 2018;8(12):403–425. doi: 10.3390/coatings8120443
19.
BedardBA, FlanaganTJ, ErnstAT, Microstructure and micromechanical response in gas-atomized Al 6061 alloy powder and cold-sprayed splats. J Therm Spray Technol. 2018;27(8):1563–1578. doi: 10.1007/s11666-018-0785-0
20.
JenkinsR, AldwellB, YinS, Solid state additive manufacture of highly-reflective Al coatings using cold spray. Opt Laser Technol. 2019;115:251–256. doi: 10.1016/j.optlastec.2019.02.011
21.
NikbakhtaR, SeyedeinbSH, KheirandishcS, The role of deposition sequence in cold spraying of dissimilar materials. Surf Coat Technol. 2019;367:75–85. doi: 10.1016/j.surfcoat.2019.03.065
