Electron beam physical vapour deposition is a reliable technique used to deposit coatings with desired microstructures; however, controlling the chemical composition of the alloy coatings is not simple and several features should be considered. The aim of this paper is to summarise and establish the connection between the important work that has been done in this area to achieve a homogeneous and controlled chemical composition in the deposited film. Technical and fundamental aspects are discussed.
SinghJ, WolfeDE.Nanostructured component fabrication by electron beam-physical vapor deposition. J Mater Eng Perform. 2005;14:448–459. doi: 10.1361/105994905X56223
2.
MellorBG.Surface coatings for protection against wear. 1st ed. Cambridge
: Woodhead Publishing; 2006.
3.
PomeroyMJ.Coatings for gas turbine materials and long term stability issues. Mater Des. 2005;26:223–231. doi: 10.1016/j.matdes.2004.02.005
4.
MartinPM.Handbook of deposition technologies for films and coatings. 3rd ed. Oxford
: Science, Applications and Technology, Elsevier; 2010.
5.
GrovesJF.Directed vapor deposition [Ph.D. Thesis]. University of Virginia; 1998.
SinghJ, WolfeDE, MillerRA, Tailored microstructure of zirconia and hafnia-based thermal barrier coatings with low thermal conductivity and high hemispherical reflectance by EB-PVD. J Mater Sci. 2004;39:1975–1985. doi: 10.1023/B:JMSC.0000017759.50800.d7
9.
PowellA, MinsonP, TrapagaG, Mathematical modeling of vapor-plume focusing in electron-beam evaporation. Metall Mater Trans A. 2001 Aug;32A:1959–1966. doi: 10.1007/s11661-001-0008-y
10.
XinY, HeXD, LiMW, The composition variation in evaporation of multi-component alloys by EB-PVD. J Comput Theor Nanosci. 2008 Aug;5(8):1696–1699. doi: 10.1166/jctn.2008.855
11.
HarshaKSS.Principles of physical vapor deposition of thin films. 1st ed. Elsevier; 2006.
12.
OhringM.The materials science of thin films. San Diego (CA
): Academic Press; 1992.
13.
IvanchenkoVG, IvasishinOM, SemiatinSL.Evaluation of evaporation losses during electron-beam melting of Ti-Al-V alloys. Metall MaterTrans B. 2003 Dec;34B:911–915. doi: 10.1007/s11663-003-0097-7
14.
YuZ, HassDD, WadleyHNG.Nial bond coats made by a directed vapor deposition approach. Mater Sci Eng: A. 2005;394:43–52. doi: 10.1016/j.msea.2004.11.017
PowellA, AvyleJVD, DamkrogerB, Analysis of multicomponent evaporation in electron beam melting and refining of titanium alloys. Metall Mater Trans B. 1997 Dec;28 B:1227–1239. doi: 10.1007/s11663-997-0078-3
17.
MetznerC, ScheffelB.Special aspects concerning the electron beam deposition of multicomponent alloys. Surf Coat Technol. 2001;146-147:491–497. doi: 10.1016/S0257-8972(01)01460-8
18.
MartinPM.Handbook of deposition technologies for films and coatings. 3rd ed. Oxford
: Applications and Technology, Elsevier; 2010.
19.
AlmeidaDSD, SilvaCRMD, CarmoMD, 2006. Proc. 17th Brazilian Congress of Engineering and Materials Science, Iguazu Falls, Brazil, 15–19 November 2006.
20.
LiM, Xiao-dongH, YueS.Preparation of Ti-Al alloy sheet by electron beam physical vapor deposition. Trans Nonferrous Metal Soc China. 2007;17:477–481.
FanT, YangG, ZhangD.Prediction of chemical stability in SiCp/Al composites with alloying element addition using Wilson equation and an extended Miedema model. Mater Sci Eng: A. 2005;394:327–338. doi: 10.1016/j.msea.2004.11.040
23.
SmithJM, Van NessHC, AbbottMM.Introduction to chemical engineering thermodynamics, Sixth Edition in SI Units. Boston
: McGraw-Hill; 2001.
24.
MiedemaAR, ChatelPFD, BoerFRD.Cohesion in alloys-fundamentals of a semi-empirical model. Physica. 1980;100 B:1–28.
