Hot corrosion behaviour of Carbon Nanotubes (CNT) reinforced Cr2O3 composite coatings have been investigated in actual boiler environment of a thermal power plant at 900°C under cyclic thermal loading conditions. The CNT content was varied from 1 to 8 wt-% and the coatings were deposited with the high-velocity oxy-fuel method. The comparative effects of variation in CNT content (from 1 to 8 wt-%) on hot corrosion behaviour were studied by weight change analysis and corrosion products were analysed with X-ray diffraction, scanning electron microscopy, energy dispersive and cross-sectional analysis techniques. The results confirmed that variation in CNT content enhanced the corrosion resistance of surface coatings in actual boiler environment at elevated temperature. The coatings showed lower weight gain along with the formation of protective oxide scales during the experiment. Reduction in corrosion rates during hot corrosion was observed with an increase in CNT content in the coating matrix.
WielageB, HofmannU, SteinhauserS, Improving wear and corrosion resistance of thermal sprayed coatings. Surf Eng. 1998;14:136–138. doi: 10.1179/sur.1998.14.2.136
3.
KeyvaniA, BahamirianM.Hot corrosion and mechanical properties of nanostructured Al2O3/CSZ composite TBCs. Surf Eng. 2017;33:433–443. doi: 10.1080/02670844.2016.1267423
4.
MemmiIT.Ceramic coatings in ancient times: high technology surface modification technologies. Surf Eng. 2013;29:84–97. doi: 10.1179/1743294412Y.0000000078
5.
AndersonA.Corrosion resistance of ceramic coatings sprayed on stainless steel substrates. Int J Amb Ener. 2017;38:320–322. doi: 10.1080/01430750.2015.1086679
6.
PawlowskiL.The science and engineering of thermal spray coatings. West Sussex
: John Wiley & Sons; 2008.
7.
FukanumaH.A porosity formation and flattening model of an impinging molten particle in thermal spray coatings. J Therm Spray Technol. 1994;3:33–44. doi: 10.1007/BF02648997
8.
ChathaSS, SidhuHS, SidhuBS.Characterisation and corrosion-erosion behaviour of carbide based thermal spray coatings. J Min Mater Char Eng. 2012;11:569–586.
WangF, GengS.High temperature oxidation and corrosion resistant nanocrystalline coatings. Surf Eng. 2003;19:32–36. doi: 10.1179/026708402225010056
11.
XuS, ChenL, GongM, Characterization and engineering application of a novel ceramic composite insulation material. Comp B: Eng. 2017;111:143–147. doi: 10.1016/j.compositesb.2016.12.010
12.
DussingM, YangH, ToppingTD, Microstructure and mechanical behavior of cryomilled Al–Mg composites reinforced with nanometric yttria partially stabilized zirconia. Cham
: Springer; 2018.
13.
SuibSL.A review of nanoceramic materials for use in ceramic matrix composites. Sol-gel based nanoceramic materials: preparation, properties and applications. Cham
: Springer; 2017. p. 185–230.
14.
MartinR, VickM, EnnetiRK, Sintering characteristics of a powder injection molded ceria-stabilized zirconia–mullite composite. Mater Manuf Process. 2015;30:616–623. doi: 10.1080/10426914.2014.941871
15.
ChenY, BalaniK, AgarwalA.Modified Eshelby tensor modeling for elastic property prediction of carbon nanotube reinforced ceramic nanocomposites. Appl Phys Lett. 2007;91:1–3. 031903.
16.
GongM, MeiF, QiaoS, Determination of strength properties for yttria stabilised zirconia coatings. Surf Eng. 2015;31:308–315. doi: 10.1179/1743294415Y.0000000004
17.
HvizdošP, PuchýV, DuszováA, Carbon nanofibers reinforced ceramic matrix composites. Rijeka
: InTech Open Access Publishers; 2011. p. 241–266.
18.
SalehTA, GuptaVK.Characterization of the chemical bonding between Al2O3 and nanotube in MWCNT/Al2O3 nanocomposite. Curr Nano. 2012;8:739–743. doi: 10.2174/157341312802884418
19.
DengC, WangD, ZhangX, Processing and properties of carbon nanotubes reinforced aluminum composites. Mater Sci Eng A. 2007;444:138–145. doi: 10.1016/j.msea.2006.08.057
AslMS, FarahbakhshI, NayebiB.Characteristics of multi-walled carbon nanotube toughened ZrB2–SiC ceramic composite prepared by hot pressing. Ceram Int. 2016;42:1950–1958. doi: 10.1016/j.ceramint.2015.09.165
22.
LiuY, RamirezC, ZhangL, In situ direct observation of toughening in isotropic nanocomposites of alumina ceramic and multiwall carbon nanotubes. Acta Mater. 2017;127:203–210. doi: 10.1016/j.actamat.2017.01.024
23.
NisarA, BalaniK.Phase and microstructural correlation of spark plasma sintered HfB2-ZrB2 based Ultra-high temperature ceramic composites. Coatings. 2017;7:1–15.
ChenW, TuJ, WangL, Tribological application of carbon nanotubes in a metal-based composite coating and composites. Carbon N Y. 2003;41:215–222. doi: 10.1016/S0008-6223(02)00265-8
BalaniK, ChenY, HarimkarSP, Tribological behavior of plasma-sprayed carbon nanotube-reinforced hydroxyapatite coating in physiological solution. Acta Biomater. 2007;3:944–951. doi: 10.1016/j.actbio.2007.06.001
29.
GoyalR, SidhuBS, ChawlaV.Improving the high-temperature oxidation resistance of ASME-SA213-T11 boiler tube steel by plasma spraying with CNT-reinforced alumina coatings. Anti Corr Met Mater. 2018;65:217–223. doi: 10.1108/ACMM-03-2017-1778
30.
GoyalK, SinghH, BhatiaR.Effect of carbon nanotubes on properties of ceramics based composite coatings. Adv Eng Forum. 2018;26:53–66. doi: 10.4028/www.scientific.net/AEF.26.53
31.
GoyalK, SinghH, BhatiaR.Experimental investigations of carbon nanotubes reinforcement on properties of ceramics based composite coating, J Aus Ceram Soc.2018. Published online first. doi:10.1007/s41779-018-0237-9.
32.
GoyalK, SinghH, BhatiaR.Mechanical and microstructural properties of carbon nanotubes reinforced chromium oxide coated boiler steel. World J Eng. 2018. published online. doi:10.1108/WJE-10-2017-0315.
33.
BalaN, SinghH, PrakashS.Accelerated hot corrosion studies of cold spray Ni–50Cr coating on boiler steels. Mater Des. 2010;31:244–253. doi: 10.1016/j.matdes.2009.06.033
34.
PrakashS, SinghS, SidhuB.Tube failures incoal fired boilers. Proceedings of National Seminar on Advances in Material and Processing. India: Indian Institute of Roorkee; 2001. p. 245–253.
35.
SidhuT, PrakashS, AgrawalR.Characterisations of HVOF sprayed NiCrBSi coatings on Ni-and Fe-based superalloys and evaluation of cyclic oxidation behaviour of some Ni-based superalloys in molten salt environment. Thin Solid Films. 2006;515:95–105. doi: 10.1016/j.tsf.2005.12.041
36.
GhoshD, MitraS.Plasma sprayed Cr3C2–Ni–Cr coating for oxidation protection of 2· 25Cr–1Mo steel. Surf Eng. 2015;31:342–348. doi: 10.1179/1743294414Y.0000000336
37.
MishraS, PrakashS.Erosion–corrosion behaviour of Ni–20Cr plasma coating in actual boiler environment. Surf Eng. 2015;31:29–38. doi: 10.1179/1743294414Y.0000000338
38.
SinghalS, PasrichaR, JangraM, Carbon nanotubes: amino functionalization and its application in the fabrication of Al-matrix composites. Powder Technol. 2012;215:254–263. doi: 10.1016/j.powtec.2011.10.013
39.
AhmadI, UnwinM, CaoH, Multi-walled carbon nanotubes reinforced Al 2 O 3 nanocomposites: mechanical properties and interfacial investigations. Comp Sci Technol. 2010;70:1199–1206. doi: 10.1016/j.compscitech.2010.03.007
Bakhsheshi-RadH, HamzahE, IsmailA, Titania-carbon nanotubes nanocomposite coating on Mg alloy: microstructural characterisation and mechanical properties. Mater Sci Technol. 2018;34:378–387. doi: 10.1080/02670836.2017.1393975
42.
YildirimM, ÖzyürekD, GürüM.Investigation of microstructure and wear behaviors of al matrix composites reinforced by carbon nanotube. Fullerenes Nanotubes Carbon Nanostruct. 2016;24:467–473. doi: 10.1080/1536383X.2016.1182504
43.
HanG, WangZ, LiuK, Synthesis of CNT-reinforced AZ31 magnesium alloy composites with uniformly distributed CNTs. Mater Sci Eng A. 2015;628:350–357. doi: 10.1016/j.msea.2015.01.039
44.
GuoW, TamH-Y.Effects of carbon nanotubes on wear of WC/Co micropunches. Int J Adv Manuf Technol. 2014;72:269–275. doi: 10.1007/s00170-014-5661-6
45.
GoyalR, SidhuBS, ChawlaV.Characterization of plasma-sprayed carbon nanotube (CNT)-reinforced alumina coatings on ASME-SA213-T11 boiler tube steel. Int J Adv Manuf Technol. 2017;92(9-12):3225–3235. doi: 10.1007/s00170-017-0405-z
46.
GoyalR, ChawlaV, SidhuBS.Study on porosity of plasma sprayed carbon nano tube reinforced composite coatings. Asian Rev Mech Eng. 2014;3:65–69.
47.
KeshriAK, HuangJ, SinghV, Synthesis of aluminum oxide coating with carbon nanotube reinforcement produced by chemical vapor deposition for improved fracture and wear resistance. Carbon. 2010;48:431–442. doi: 10.1016/j.carbon.2009.08.046
