Fe-based coatings were fabricated on GCr15 bearing steel by laser cladding assisted by ultrasonic vibration. Microstructural evolution and wear resistance of the cladding layers were investigated systematically. The results showed that epitaxial growth columnar grains were shattered and then grew in different directions with a large number of fine equiaxed crystals formed in the cladding layer. The nano-hardness and elastic modulus were 10.54 and 289.3 GPa, and increased by 15.7 and 4.9%, respectively, compared to a cladding layer without ultrasonic vibration-assisted. The average friction coefficient of cladding layer with and without ultrasonic vibration was 0.339 and 0.382, respectively, which decreased by 18.5 and 8.2% accordingly compared to the substrate (0.416), and the corresponding relative wear-resisting coefficients were 47.1 and 21.4 times as high as that of the substrate. The wear resistance of the cladding layer was better than that of the substrate, especially the cladding layer fabricated by ultrasonic vibration.
YinF, HuaL, MaoH, Microstructural modeling and simulation for GCr15 steel during elevated temperature deformation. Mater Des. 2013;55(6):560–573.
2.
FuJ.Microstructure and corrosion behavior of hot-rolled GCr15 bearing steel. Appl Phys A. 2016;122(4):416.
3.
ZhouJ, XuJ, HuangS, Microstructure and mechanical properties of Cr12MoV by ultrasonic vibration-assisted laser surface melting. Mater Sci Technol. 2017;33(10):1200–1207.
4.
RiveiroA, MejíasA, LusquiñosF, Laser cladding of aluminium on AISI 304 stainless steel with high-power diode lasers. Surf Coat Technol. 2014;253(9):214–220.
5.
QunshuangM, YajiangL, JuanW.Surface modification of Q550 HSLA steel with Co-Fe-Cr composite coatings manufactured by fibre laser cladding. Surf Eng. 2016;32(12):934–942.
6.
WengF, YuH, LiuJ, Microstructure and wear property of the Ti 5 Si 3/TiC reinforced Co-based coatings fabricated by laser cladding on Ti-6Al-4V. Opt Laser Technol. 2017;92:156–162.
7.
WangY, LiuB, GuoZ.Wear resistance of machine tools’ bionic linear rolling guides by laser cladding. Opt Laser Technol. 2017;91:55–62.
8.
TuominenJ, NäkkiJ, PajukoskiH, Microstructural and abrasion wear characteristics of laser-clad tool steel coatings. Surf Eng. 2016;32(12):923–933.
9.
ForoozmehrE, LinD, KovacevicR.Application of vibration in the laser powder deposition process. J Manuf Process. 2009;11(1):38–44.
10.
LiM, HanB, WangY, Investigation on laser cladding high-hardness nano-ceramic coating assisted by ultrasonic vibration processing. Optik-Int J Light Electron Optics. 2016;127(11):4596–4600.
11.
WuD, GuoM, MaG, Dilution characteristics of ultrasonic assisted laser clad yttria-stabilized zirconia coating. Mater Lett. 2015;141:207–209.
12.
GaoW, ZhaoS, LiuF, Effect of defocus manner on laser cladding of Fe-based alloy powder. Surf Coat Technol. 2014;248(13):54–62.
13.
MakuchN, KulkaM, DziarskiP, Laser surface alloying of commercially pure titanium with boron and carbon. Opt Lasers Eng. 2014;57(6):64–81.
14.
HuangY, ZengX, HuQ, Microstructure and interface interaction in laser induction hybrid cladding of Ni-based coating. Appl Surf Sci. 2009;255(7):3940–3945.
15.
XuP, LinCX, ZhouCY, Wear and corrosion resistance of laser cladding AISI 304 stainless steel/Al2O3, composite coatings. Surf Coat Technol. 2014;238(2):9–14.
16.
LiuF, MaoY, LinX, Microstructure and high temperature oxidation resistance of Ti-Ni gradient coating on TA2 titanium alloy fabricated by laser cladding. Opt Laser Technol. 2016;83:140–147.
17.
OhYK, ParkSH, ChoYI.A study of the effect of ultrasonic vibrations on phase-change heat transfer. Int J Heat Mass Transf. 2002;45(23):4631–4641.
18.
LiuX, OsawaY, TakamoriS, Microstructure and mechanical properties of AZ91 alloy produced with ultrasonic vibration. Mat Sc Eng: A. 2008;487(1–2):120–123.
19.
LiuH, XuQ, WangC, Corrosion and wear behavior of Ni60CuMoW coatings fabricated by combination of laser cladding and mechanical vibration processing. J Alloys Compd. 2015;621:357–363.
20.
ZhouS, XiongZ, DaiX, Microstructure and oxidation resistance of cryomilled NiCrAlY coating by laser induction hybrid rapid cladding. Surf Coat Technol. 2014;258(12):943–949.
21.
CaiCX, LiuHX, JiangYH, Influence of AC magnetic field on microstructure and wear behaviors of laser cladding Fe-based composite coating. Tribology. 2013;33(3):229–235.
22.
LiuHX, TaoXD, ZhangXW, Microstructure and interface distribution of Fe-Cr-Si-B-C laser cladding alloy coatings assisted by mechanical vibration. Opt Precis Eng. 2015;23(8):2192–2202.
23.
WuG, RenF, YaoJ, Abrasion resistance mechanism of new cobalt based alloy by diode laser cladding. Chinese J Lasers. 2017;44(06):0602006.
24.
XuanHF, WangQY, BaiSL, A study on microstructure and flame erosion mechanism of a graded Ni-Cr-B-Si coating prepared by laser cladding. Surf Coat Technol. 2014;244(15):203–209.
25.
QiuZ, ZhangP, WeiD, Tribological behavior of CrCoNiAlTiY coating synthesized by double-glow plasma surface alloying technique. Tribol Int. 2015;92:512–518.
26.
MasantaM, ShariffSM, ChoudhuryAR.Evaluation of modulus of elasticity, nano-hardness and fracture toughness of TiB2–TiC–Al2O3 composite coating developed by SHS and laser cladding. Mat Sci Eng A. 2011;528(16):5327–5335.
27.
LeylandA, MatthewsA.On the significance of the H/E, ratio in wear control: a nanocomposite coating approach to optimised tribological behaviour. Wear. 2000;246(1–2):1–11.
28.
XuJ, FanHS, LiZY.Role of Al additions in wear control of nanocrystalline Mo(Si1−xAlx)2 coatings prepared by double cathode glow discharge technique. Mater Sci Technol. 2013;29(8):900–907.
29.
TanH, LuoZ, LiY, Effect of strengthening particles on the dry sliding wear behavior of Al2O3–M7C3/Fe metal matrix composite coatings produced by laser cladding. Wear. 2015;s324–325:36–44.
30.
DuZM, LiJP.Study of the preparation of Al2O3sf·SiCp/Al composites and their wear-resisting properties. J Mat Process Tech. 2004;151(1):298–301.
31.
ChenC, LuC, FengX, Effects of annealing on Al–Si coating synthesised by mechanical alloying. Surf Eng. 2017;33(7):548–558.
