High-velocity oxy-fuel sprayed, iron alloy-based powder coatings, reinforced with tungsten carbide–cobalt (WC–Co) and titanium carbide–nickel molybdenum (TiC–NiMo) cermet particles, are compared under high-temperature abrasive–erosive wear conditions. Both WC–Co and TiC–NiMo particles underwent fracture, as well as dissolution, during the spraying process, but in the case of WC–Co particles this process was remarkably less intensive. Under the low impact angle conditions, the WC–Co particle-reinforced coating exhibited 1.1 times lower wear than the TiC–NiMo particle-reinforced coating because of the larger amount of the reinforcement remaining. Under the normal impact angle conditions, the WC–Co particle-reinforced coating showed 1.2 times lower wear than the TiC–NiMo particle-reinforced coating because of the resulting larger size of the WC–Co reinforcement and a more ductile matrix.
ShimizuK., XinbaY. and ArayaS.: ‘Solid particle erosion and mechanical properties of stainless steels at elevated temperatures’, Wear, 2011,
271, (9–10), 1357–1364. doi: 10.1016/j.wear.2010.12.038
2.
YangJ.-Z., FangM.-H., HuangZ. H., HuX.-Z., LiuY.-G., SunH.-h., HuangJ.-T. and LiX.-C.: ‘Solid particle impact erosion of alumina-based refractories at elevated temperatures’, J. Eur. Ceram. Soc., 2012,
32, (2), 283–289. doi: 10.1016/j.jeurceramsoc.2011.08.017
3.
WangX., FangM., ZhangL.-C., DingH., LiuY.-G., HuangZ., HuangS. and YangJ.: ‘Solid particle erosion of alumina ceramics at elevated temperature’, Mater. Chem. Phys., 2013,
139, (2–3), 765–769. doi: 10.1016/j.matchemphys.2013.02.029
4.
YaoM., DeJongL. and DeWetD., Kennametal Inc.: ‘Wear resistant inner coating for pipes and pipe fittings’, US Patent 8962154, 24 February 2015.
5.
YangY., SunC., SunJ., ZhaoW., DongL., LiL. and MengF.: ‘Erosion behaviour of arc sprayed FeTi/CrB MMC coating at elevated temperature’, Surf. Coat. Technol., 2015,
262, 141–147. doi: 10.1016/j.surfcoat.2014.12.027
6.
MatthewsS., JamesB. and HylandM.: ‘High temperature erosion-oxidation of Cr3C2–NiCr thermal spray coatings under simulated turbine conditions’, Corros. Sci., 2013,
70, 203–211. doi: 10.1016/j.corsci.2013.01.030
7.
TylczakJ. H.: ‘Erosion–corrosion of iron and nickel alloys at elevated temperature in a combustion gas environment’, Wear, 2013,
302, (1–2), 1633–1641. doi: 10.1016/j.wear.2013.01.008
8.
MishraS. B., ChandraK. and PrakashS.: ‘Erosion–corrosion performance of NiCrAlY coating produced by plasma spray process in a coal-fired thermal power plant’, Surf. Coat. Technol., 2013,
216, 23–34. doi: 10.1016/j.surfcoat.2012.09.044
9.
PatelR. D. and PatelI. J.: ‘A review paper on erosion and corrosion behaviour of coal combustion chamber’, Int. J. Innov. Res. Sci. Technol., 2014,
1, (7), 72–76.
10.
MishraS. B. and PrakashS.: ‘Erosion–corrosion behaviour of Ni–20Cr plasma coating in actual boiler environment’, Surf. Eng., 2015,
31, (1), 29–38. doi: 10.1179/1743294414Y.0000000338
11.
BalamanikandasuthanK., ArunK. and PalamSharath Sekar: ‘Design and fabrication of erosion protection shield for boiler tubes and its analysis’, Int. J. Res. Mech. Mater. Eng., 2015,
1, (1), 39–52.
12.
Higuera HidalgoV., Belzunce VarelaJ., Earriles MenéndezA. and Poveda MartínezS.: ‘High temperature erosion wear of flame and plasma sprayed nickel–chromium coatings under simulated coal-fired boiler atmospheres’, Wear, 2001,
247, 214–222. doi: 10.1016/S0043-1648(00)00540-8
13.
VenugopalK. and AgrawalM.: ‘Evaluation of arc sprayed coatings for erosion protection of tubes in atmospheric fluidized bed combustion (AFBC) boilers’, Wear, 2008,
264, (1–2), 139–145. doi: 10.1016/j.wear.2007.05.013
14.
CaiL.-X., MaoJ.-R., WangS.-S., DiJ. and FengZ.-P.: ‘Experimental investigation of erosion resistance of iron boride coatings for steam turbines at high temperatures’, Proc. Inst. Mech. Eng., Part J., 2015,
229, (5), 636–645. doi: 10.1177/1350650114557105
15.
MatthewsS., JamesB. and HylandM.: ‘High temperature erosion of Cr3C2–NiCr thermal spray coatings – the role of phase microstructure’, Surf. Coat. Technol., 2009,
203, (9), 1144–1153. doi: 10.1016/j.surfcoat.2008.10.008
16.
ChaS. C. and WölpertP.: ‘High-temperature erosion and corrosion measurement of thermally sprayed materials’, Adv. Eng. Mater., 2003,
5, (4), 213–217. doi: 10.1002/adem.200300227
17.
PraveenA. S., SaranganJ., SureshS. and Siva SubramanianJ.: ‘Erosion wear behavior of plasma sprayed NiCrSiB/Al2O3 composite coating’, Int. J. Refract. Met. Hard Mater., 2015,
52, 209–218. doi: 10.1016/j.ijrmhm.2015.06.005
18.
SharmaS.: ‘High temperature erosive wear study of NiCrFeSiB flame sprayed coatings’, J. Inst. Eng. (India): Ser. D, 2012,
93, (1), 7–12.
19.
LiR., ZhouZ., HeD., WangY., WuX. and SongX.: ‘Microstructure and high temperature corrosion behaviour of wire-arc sprayed FeCrSiB coating’, J. Therm. Spray Technol., 2015,
24, (5), 857–864. doi: 10.1007/s11666-015-0244-0
20.
WielageB., PokhmurskaH., StudentM., GvozdeckiiV., StupnickyjT. and PokhmurskiiV.: ‘Iron-based coatings arc-sprayed with cored wires for application at elevated temperatures’, Surf. Coat. Technol., 2013,
220, 27–35. doi: 10.1016/j.surfcoat.2012.12.013
21.
SurzhenkovA., VallikiviA., MikliV., ViljusM., VilgoT. and KuluP.: ‘Wear resistant self-fluxing alloy based TiC–NiMo and Cr2C3–Ni hardmetal particles reinforced composite coatings’, Proc. 2nd Int. Conf. ‘Industrial Engineering & Management’, Prešov, Slovak Republic, December 2012, Technical University of Košice, 34–37.
22.
SurzhenkovA., KuluP., TarbeR., MikliV., SarjasH. and LatokartanoJ.: ‘Wear resistance of laser remelted thermally sprayed coatings’, Est. J. Eng., 2009,
15, (4), 318–328. doi: 10.3176/eng.2009.4.09
23.
SarjasH., GoljandinD., KuluP., MikliV., SurženkovA. and VuoristoP.: ‘Wear resistant thermal sprayed composite coatings based on iron self-fluxing alloy and recycled cermet powders’, Mater. Sci. (Medžiagotyra), 2012,
18, (1), 34–39.
24.
BolelliG., BonferroniB., LaurilaJ., LusvarghiL., MilantiA., NiemiK. and VuoristoP.: ‘Micromechanical properties and sliding wear behavior of HVOF-sprayed Fe-based alloy coatings’, Wear, 2012,
276–277, 29–47. doi: 10.1016/j.wear.2011.12.001
25.
LiR., HeD. Y., ZhouZ., WangZ. J. and SongX. Y.: ‘Wear and high temperature oxidation behavior of wire arc sprayed iron based coatings’, Surf. Eng., 2014,
30, (11), 784–790. doi: 10.1179/1743294414Y.0000000331
26.
LampkeT., WielageB., PokhmurskaH., RupprechtC., SchuberthS., DrehmannR. and SchreiberF.: ‘Development of particle reinforced nanostructured iron-based composite alloys for thermal spraying’, Surf. Coat. Technol., 2011,
205, (12), 3671–3676. doi: 10.1016/j.surfcoat.2011.01.003
27.
AkimenkoV. B.: ‘Production of the powders of iron and iron-based alloys in the USSR’, Sov. Powder Metall., 1992,
31, (1), 1–5.
28.
EuB.-Y., HeD.-Y., JiangJ.-M. and LiX.-Y.: ‘Microstructure and wear behaviour of arc sprayed WC–Co/FeCrB and WC–Ni/FeCrB composite coatings’, Key Eng. Mater., 2008,
373–374, 468–471. doi: 10.4028/www.scientific.net/KEM.373-374.468
29.
SurzhenkovA., AntonovM., GoljandinD., VilgoT., MikliV., ViljusM., LatokartanoJ. and KuluP.: ‘Sliding wear of TiC–NiMo and Cr3C2–Ni cermet particles reinforced FeCrSiB matrix HVOF sprayed coatings’, Est. J. Eng., 2013,
19, (3), 203–211. doi: 10.3176/eng.2013.3.03
30.
ZikinA., AntonovM., HussainovaI., KatonaL. and GavrilovićA.: ‘High temperature wear of cermet particles reinforced NiCrBSi hardfacings’, Tribol. Int., 2013,
68, 45–55. doi: 10.1016/j.triboint.2012.08.013
31.
AntonovM., HussainovaI., PirsoJ. and VolobuevaO.: ‘Assessment of mechanically mixed layer developed during high temperature erosion of cermets’, Wear, 2007,
263, (7–12), 878–886. doi: 10.1016/j.wear.2006.12.035
32.
SurzhenkovA., GoljandinD., TraksmaaR., ViljusM., TalvisteK., AruniitA., LatokartanoJ. and KuluP.: ‘High temperature erosion wear of cermet particles reinforced self-fluxing alloy HVOF sprayed coatings’, Mater. Sci. (Medžiagotyra), 2015,
21, (3), 386–390.
33.
ZhangZ.-Q., LiG.-L., WangH.-D., XuB.-S., PiaoZ.-Y. and ZhuZ.-N.: ‘Investigation of rolling contact fatigue damage process of the coating by acoustic emission and vibration signals’, Tribol. Int., 2012,
47, 25–31. doi: 10.1016/j.triboint.2011.10.002
34.
PirsoJ., ViljusM., JuhaniK. and KuningasM.: ‘Three-body abrasive wear of TiC–NiMo cermets’, Tribol. Int., 2010,
43, (1–2), 340–346. doi: 10.1016/j.triboint.2009.06.014
35.
PirsoJ., ViljusM., LetunovitšS., JuhaniK. and JoostR.: ‘Three-body abrasive wear of cermets’, Wear, 2011,
271, (11–12), 2868–2878. doi: 10.1016/j.wear.2011.06.005
36.
DavisJ. R. (ed.): ‘Handbook of thermal spray technology’; 2004, Materials Park, OH
, ASM International.
37.
AntonovM., SurženkovA., HussainovaI., GoljandinD. and MikliV.: ‘Effect of basalt addition on tribological performance of FeCrSiB HVOF coatings’, Est. J. Eng., 2012,
18, (4), 221–220.
38.
WellmanR. G. and NicholsJ. R.: ‘High temperature erosion–oxidation mechanisms, maps and models’, Wear, 2004,
256, 907–917. doi: 10.1016/j.wear.2003.04.003
39.
KleisI. and KuluP.: ‘Solid particle erosion: occurrence, prognostification and control’, Chap. 4, ‘Erosion resistance of powder materials and coatings’, 153–196; 2008, London
, Springer-Verlag London Ltd.
