Several key properties of aluminium semi-finished products, including formability, softening behaviour, strength and ductility, are influenced by the constitution of alloying elements in solid solution or in precipitated form, i.e. by the materials microchemistry. In the present paper, we study microchemistry reactions in two Al–Mg–Si automotive sheet alloys, AA 6005C and AA 6016, with different Mg:Si ratios. The formation of constituent phases and dispersoids during solidification and subsequent homogenisation is analysed by scanning electron microscopy and measurements of the specific electrical resistivity. Type, composition and volume fraction of the constituent phases in the as-cast state are assessed with the Alstruc solidification model. The changes in solute level and precipitation during homogenisation are traced with a statistical microchemistry simulation tool termed ClaNG.
BurgerGBGuptaAKJeffreyPWMicrostructural control of aluminum sheet used in automotive applications. Mater Char. 1995;35(1):23–39.
2.
MillerWSZhuangLBottemaJRecent development in aluminium alloys for the automotive industry. Mater Sci Eng. 2000;A280(1):37–49.
3.
EnglerOHirschJ.Texture control by thermomechanical processing of AA6xxx Al–Mg–Si sheet alloys for automotive applications—a review. Mater Sci Eng. 2002;A336(1-2):249–262.
4.
HirschJ.Aluminium in innovative light-weight car design. Mater Trans. 2011;52(5):818–824.
5.
BloeckM.Aluminium sheet for automotive applications. In: RoweJ, editor. Advanced materials in automotive engineering. Cambridge (UK): Woodhead Publishing; 2012. p. 85–108.
6.
AndersenSJZandbergenHWJansenJThe crystal structure of the β'' phase in Al–Mg–Si alloys. Acta Mater. 1998;46(9):3283–3298.
7.
HastingHSFrøsethAGAndersenSJComposition of β” precipitates in Al–Mg–Si alloys by atom probe tomography and first principles calculations.J Appl Phys. 2009;106(12):123527.
8.
Mrówka-NowotnikGSieniawskiJWierzbińskaM.Analysis of intermetallic particles in AlSi1MgMn aluminium alloy. J Ach Mater Manuf Eng. 2007;20:155–158.
9.
VermaAKumarSGrantPSInfluence of cooling rate on the Fe intermetallic formation in an AA6063 Al alloy. J Alloys Compd. 2013;555:274–282.
10.
SarafoglouPIHaidemenopoulosGN.Phase fraction mapping in the as-cast microstructure of extrudable 6xxx aluminum alloys. Int J Mater Res. 2014;105(12):1202–1209.
11.
PrillhoferRRankGBernederJProperty criteria for automotive Al–Mg–Si sheet alloys. Materials (Basel). 2014;7:5047–5068.
12.
LodgaardLRyumN.Precipitation of dispersoids containing Mn and/or Cr in Al–Mg–Si alloys. Mater Sci Eng. 2000;A283(1–2):144–152.
13.
SuniJPRounsTN.Dispersoid evolution during homogenization of 6xxx alloys. Mater Sci Forum. 2002;687–692:396–402.
14.
StrobelKEastonMSweetERelating quench sensitivity to microstructure in 6000 series aluminium alloys. Mater Trans. 2011;52:914–919.
15.
RemøeMSMarthinsenKWestermannIThe effect of alloying elements on the ductility of Al–Mg–Si alloys. Mater Sci Eng. 2017;A693:60–72.
16.
LiuCLDuQParsonNCThe interaction between Mn and Fe on the precipitation of Mn/Fe dispersoids in Al–Mg–Si–Mn–Fe alloys. Scripta Mater. 2018;152:59–63.
17.
MatsudaKUetaniYSatoTMetastable phases in an Al–Mg–Si alloy containing copper. Metall Mater Trans. 2001;32A(6):1293–1299.
18.
WangXPooleWJEsmaeiliSPrecipitation strengthening of the aluminum alloy AA6111. Metall Mater Trans. 2003;34A(12):2913–2924.
19.
MarioaraCDAndersenSJSteneTNThe effect of Cu on precipitation in Al–Mg–Si alloys. Phil Mag. 2007;87:385–3413.
20.
ZajacSHutchinsonBJohanssonAMicrostructure control and extrudability of Al–Mg–Si alloys microalloyed with manganese. Mater Sci Technol. 1994;10(4):323–333.
21.
KuijpersNCWVermolenFJVuikCThe dependence of the β-AlFeSi to α-Al(FeMn)Si transformation kinetics in Al–Mg–Si alloys on the alloying elements. Mater Sci Eng. 2005;A394(1–2):9–19.
22.
RøysetJ.BaugerØ.SæterJ.A.Homogenization of Al–Mg–Si alloy billets—myths and facts. Proceedings of the 10th International Aluminum Extrusion Technology Seminar, May 15–18, 2012, Miami (FL), Vol. II, 2012. p. 171–185.
23.
YanLZZhangYALiXWMicrostructural evolution of Al-0.66Mg-0.85Si alloy during homogenization. Trans Nonferrous Soc China. 2014;24(4):939–945.
24.
LiuCLAzizi-AlizaminiHParsonNCMicrostructure evolution during homogenization of Al–Mg–Si–Mn–Fe alloys: modelling and experimental results. Trans Nonferrous Soc China. 2017;27:747–753.
25.
BayatNCarlbergTCieslarM.In-situ study of phase transformations during homogenization of 6060 and 6063 Al alloys. J Phys Chem Sol. 2019;130:165–171.
26.
SarafoglouPISerafeimAFanikosIAModeling of microsegregation and homogenization of 6xxx Al-alloys including precipitation and strengthening during homogenization cooling. Materials (Basel). 2019;12(9):1421.
27.
FjeldboSKLiYMarthinsenKThrough-process sensitivity analysis on the effect of process variables on strength in extruded Al–Mg–Si alloys. J Mater Proc Technol. 2012;212(1):171–180.
28.
BirolY.Optimization of homogenization for a low alloyed AlMgSi alloy. Mater Char. 2013;80:69–75.
29.
ÖsterreicherJAKumarMSchifflASecondary precipitation during homogenization of Al–Mg–Si alloys: influence on high temperature flow stress. Mater Sci Eng. 2017;A687:175–180.
30.
QinSBendoATsuchiyaTEffect of cooling rate on precipitation during homogenization cooling in balanced Al–Mg2Si alloy. Mater Trans. 2020;61(11):2115–2120.
31.
MukhopadhyayP.Alloy designation, processing, and use of AA6XXX series aluminium alloys. Int Schol Res Network Metallurgy.2012;2012:165082.
32.
JiaoFMohlesVMirouxAThrough-process modeling of microstructure development during multi-pass hot deformation including partial recrystallization. Mater Sci Forum. 2014;794–796:652–657.
33.
LiZZhangZZhouGThe effect of Mg and Si content on the microstructure, texture and bendability of Al–Mg–Si alloys. Mater Sci Eng. 2021;A814:141199.
34.
StoudtMRHubbardJBCarsleyJECharacterizing the hemming performance of automotive aluminum alloys with high-resolution topographic imaging. J Eng Mater Technol. 2014;136:031001.
35.
GuptaAKLloydDJCourtSA.Precipitation hardening in Al–Mg–Si alloys with and without excess Si. Mater Sci Eng. 2001;A316(1-2):11–17.
36.
HirthSMMarshallGJCourtSAEffects of Si on the aging behaviour and formability of aluminium alloys based on AA6016. Mater Sci Eng. 2001;A319–A321:452–456.
37.
LangCHiscockMHollandJNew developments in automated particle analysis in the electron microscope—from micro to nano. Microsc Microanal. 2015;21(S3):337–338.
38.
EnglerOBrüggemannTHasencleverJ.Evolution of micro-chemistry during solidification and homogenisation of AA 3xxx aluminium-manganese alloys. Mater Sci Technol. 2021;37(10):893–908.
39.
DonsALJensenEKLangsrudYThe Alstruc microstructure solidification model for industrial aluminum alloys. Metall Mater Trans. 1999;30A(8):2135–2146.
40.
LiuZMohlesVEnglerOThermodynamics based modelling of the precipitation kinetics in commercial aluminium alloys. Comp Mater Sci. 2014;81:410–417.
41.
TangKDuQLiY.Modelling microstructure evolution during casting, homogenization and ageing heat treatment of Al–Mg–Si–Cu–Fe–Mn alloys. Calphad. 2018;63:164–184.
42.
BaleCWChartrandPDegterovSAFactsage thermochemical software and databases. Calphad. 2002;26(2):189–228.
43.
SaundersN.The application of calculated phase equilibria to multi-component aluminum alloys. J Jpn Inst Light Met. 2001;51:141–150.
44.
BarlockJGMondolfoLF.Structure of some aluminium–iron–magnesium–manganese–silicon alloys.Z Metallkd. 1975;66:605–611.
45.
KuijpersNCWKoolWHKoenisPTGAssessment of different techniques for quantification of α-Al(FeMn)Si and β-AlFeSi intermetallics in AA 6xxx alloys. Mater Char. 2003;49(5):409–420.
46.
LiuJ.High-resolution and low voltage FE-SEM imaging and microanalysis in materials characterization. Mater Char. 2000;44(4–5):353–363.
47.
AnselminoEMirouxAVan der ZwaagS.Dispersoid quantification and size distribution in hot and cold processed AA3103. Mater Char. 2004;52(4–5):289–300.
48.
MondolfoLF.Aluminium alloys: structure and properties. London: Butterworths; 1976.
49.
PriyaPJohnsonDRKraneMJM.Numerical study of microstructural evolution during homogenization of Al–Si-Mg–Fe–Mn alloys. Metall Mater Trans. 2016;47A(9):4625–4639.
