The flow and work hardening behaviour of pure copper (FCC), interstitial-free steel (BCC) and AZ31 magnesium (HCP) sheets were investigated under tensile and shear deformation modes. The sheets were deformed via tensile and shear punch testing (SPT) at room and 0.4Tm temperatures. The work hardening rate of sheet metals quantified by the Kocks–Mecking modelling approach was found to be significantly lower in the shear mode than in tension. Taylor factor values for the deformed samples were computed from the measured textures after tensile and shear tests to reveal the role of textural evolution on the work hardening rate. The difference in the work hardening under two strain paths was proposed to be associated with the lower Taylor factor values.
KocksUFMeckingH.Physics and phenomenology of strain hardening: the FCC case. Prog Mater Sci. 2003; 48:171–273.
2.
MeckingHKocksUF.Kinetics of flow and strain-hardening. Acta Metall. 1981; 29:1865–1875.
3.
EstrinYMeckingH.A unified phenomenological description of work hardening and creep based on one-parameter models. Acta Metall. 1984; 32:57–70.
4.
ShadkamASinclairCW.The coupled effect of grain size and solute on work hardening of Cu–Ni alloys. Philos Mag Lett. 2015; 95:555–563.
5.
SinclairCWPooleWJBréchetY.A model for the grain size dependent work hardening of copper. Scr Mater. 2006; 55:739–742.
6.
BouazizOEstrinYBréchetYCritical grain size for dislocation storage and consequences for strain hardening of nanocrystalline materials. Scr Mater. 2010; 63:477–479.
7.
AsgariSEl-DanafEKalidindiSRStrain hardening regimes and microstructural evolution during large strain compression of low stacking fault energy FCC alloys that form deformation twins. Metall Mater Trans A. 1997; 28A:1781–1795.
8.
El-DanafEKalidindiSRDohertyRD.Influence of grain size and stacking-fault energy on deformation twinning in FCC metals. Metall Mater Trans A. 1999; 30A:1223–1233.
9.
PooleWJEmburyJDLloydDJ.Work hardening in aluminum alloys. In: LumleyR.N., editor. Fundamentals of aluminum metallurgy. 1st Ed.. Cambridge, UK: Woodhead Publishing Series in Metals and Surface Engineering; 2011. p. 307–344.
10.
FangXFDahlW.Strain hardening of steels at large strain deformation. Part I: Relationship between strain hardening and microstructures of b.c.c steels. Mater Sci Eng A. 1995; 203:14–25.
11.
FangXFGusekCODahlW.Strain hardening of steels at large strain deformation. Part II: strain hardening of pearlitic and austenitic steels and the estimation of mechanical properties. Mater Sci Eng A. 1995; 203:14.
12.
ShternerVTimokhinaIBBeladiH.On the work-hardening behaviour of a high manganese TWIP steel at different deformation temperatures. Mater Sci Eng A. 2016; 669:437–446.
13.
BouazizOGueltonN.Modelling of TWIP effect on work-hardening. Mater Sci Eng A. 2001; 319-321:246–249.
14.
PerladeABouazizOFurnémontQ.A physically based model for TRIP-aided carbon steels behavior. Mater Sci Eng A. 2003; 356:145–152.
15.
LiangXMcDermidJRBouazizOMicrostructural evolution and strain hardening of Fe–24Mn and Fe–30Mn alloys during tensile deformation. Acta Mater. 2009; 57:3978–3988.
16.
WangMHuangMX.Abnormal TRIP effect on the work hardening behavior of a quenching and partitioning steel at high strain rate. Acta Mater. 2020; 188:551–559.
17.
KnezevicMLevinsonAHarrisRDeformation twinning in AZ31: influence on strain hardening and texture evolution. Acta Mater. 2010; 58:6230–6242.
18.
JainJPooleWJSinclairCW.The deformation behaviour of the magnesium alloy AZ80 at 77 and 293K. Mater Sci Eng A. 2012; 547:128–137.
19.
SalemAAKalidindiSRDohertyRD.Strain hardening of titanium: role of deformation twinning. Acta Mater. 2003; 51:4225–4237.
20.
TanXCheeWChanJImproving significantly the failure strain and work hardening response of LPSO-strengthened Mg-Y-Zn-Al alloy via hot extrusion speed control. Met Mater Int. 2017; 23:699–707.
21.
ShouHZhengJZhangYQuasi-in-situ analysis of dependency of deformation mechanism and work-hardening behavior on texture in Mg–2Zn–0.1Ca alloy. J Alloys Compd. 2019; 784:1187–1197.
22.
LiuMLinJ-YNambuSInvestigation of work hardening behavior in multilayered steels architected by twinning induced plasticity steel and martensitic steel during uniaxial tension. Mater Sci Eng A. 2021; 811:140996.
SunTShangZChoJUltra-fine-grained and gradient FeCrAl alloys with outstanding work hardening capability. Acta Mater. 2021; 215:117049.
25.
MahmudiR.Stress-state dependence of work-hardening behavior in aluminium alloy sheet. J Mater Process Technol. 1997; 72:302–307.
26.
El-DanafEKalidindiSRDohertyRD.Influence of deformation path on the strain hardening behavior and microstructure evolution in low SFE FCC metals. Int J Plast. 2001; 17:1245–1265.
27.
KaramiMMahmudiR.Work hardening behavior of the extruded and equal-channel angularly pressed Mg–Li–Zn alloys under tensile and shear deformation modes. Mater Sci Eng A. 2014; 607:512–520.
28.
YoshidaKIshiiATadanoY.Work-hardening behavior of polycrystalline aluminum alloy under multiaxial stress paths. Int J Plast. 2014; 53:17–39.
29.
LeeJBongHJKimDMechanical properties and formability of heat–treated 7000–series high–strength aluminum alloy: experiments and finite element modeling. Met Mater Int. 2017; 26:682–694.
30.
GuduruRKNagasekharAVScattergoodROFinite element analysis of a shear punch test. Metall Mater Trans A. 2006; 37A:1477–1483.
31.
GuduruRKDarlingKAKishoreREvaluation of mechanical properties using shear–punch testing. Mater Sci Eng A. 2005; 395:307–314.
32.
SarebanzadehMMahmudiRRouminaR.Constitutive analysis and processing map of an extruded Mg–3Gd–1Zn alloy under hot shear deformation. Mater Sci Eng A. 2015; 637:155–161.
33.
ZerganiAMirzadehHMahmudiR.Mechanical response of a metastable austenitic stainless steel under different deformation modes. Mater Sci Technol. 2021; 37:103–109.
34.
ZerganiAMirzadehHMahmudiR.Finite element analysis of plastic deformation in shear punch test. Mater Lett. 2021; 284:128953.
35.
UngárTTόthLSIllyJDislocation structure and work hardening in polycrystalline OFHC copper rods deformed by torsion and tension. Acta Metall. 1986; 34:1257–1267.
36.
KocksUFStoutMGRollettAD.The influence of texture on strain hardening. In: KettunenP.O.LepistöT.K.LehtonenM.E., editors. Strength of metals and alloys, (ICSMA 8). Tampere, Finland: Pergamon Press; 1988. p. 25–34.
37.
ZehetbauerMSeumerV.Cold work hardening in stages IV and V of F.C.C. metals-I. Experiments and interpretation. Acta Metall. 1993; 41:577–588.
38.
MeckingHKocksUFHartigC.Taylor factors in materials with many deformation modes. Scr Mater. 1996; 35:465–471.
39.
BungeHJ.Some applications of the Taylor theory of polycrystal plasticity. Krist Tech. 1970; 5:145–175.
40.
BeausirBTóthLSQodsFTexture and mechanical behavior of magnesium during free-end torsion. J Eng Mater Technol. 2009; 131:1.
