After continuous annealing process (CAP) at 790°C, 85% of the coils of 50% cold-rolled low carbon microalloyed (LCM) steel did not exhibit yield-strength (YS) on the target range, while the 70% cold-reduced LCM coils did. In this context, the non-isothermal recrystallisation kinetics of ferrite for the above two full-hard LCM steel were investigated using differential scanning calorimetry and the Friedman differential isoconversional method. The recrystallisation kinetics of ferrite for the two deformed states showed different behaviour. Regarding a fixed degree of cold-rolling deformation, the soaking temperature was found as the manageable parameter to control YS during CAP. Consequently, a suitable YS of the 50% cold-rolled LCM steel was achieved by setting the soaking temperature at 773°C.
HumphreysJRohrerSGRollettA.Recrystallization and related annealing phenomena recrystallization and related annealing phenomena. Amsterdam: Elsevier; 2017.
4.
Martínez-de-GuerenuAJorge-BadiolaDGutiérrezI.Assessing the recovery and recrystallization kinetics of cold rolled microalloyed steel through coercive field measurements. Mater Sci Eng A. 2017; 691:42–50. DOI: 10.1016/j.msea.2017.03.033.
5.
TojiYYamashitaTNakajimaKEffect of Mn partioning during intercritical annealing on following γ→α transformation and resultant mechanical properties of cold-rolled dual phase steels. ISIJ Int. 2011; 51:818–825. DOI: 10.2355/isijinternational.51.818.
6.
ChbihiABarbierDGermainLInteractions between ferrite recrystallization and austenite formation in high-strength steels. J Mater Sci. 2014; 49:3608–3621. DOI: 10.1007/s10853-014-8029-2.
7.
Valdes-TaberneroMACelada-CaseroCSabirovIThe effect of heating rate and soaking time on microstructure of an advanced high strenght steel. Mater Caract. 2019; 155:109822. DOI: 10.1016/j.matchar.2019.109822.
8.
MuljonoDFerryMDunneDP.Influence oh heating rate on anisothermal recrystallization in low and ultra-low carbon steels. Mater Sci Eng A. 2001; 303:90–99. DOI: 10.1016/S0921-5093(00)01882-7.
9.
FerryMMuljonoDDunneDP.Recrystallization kinetics of low and ultra low carbon steels during high-rate annealing. ISIJ Int. 2001; 41:1053–1060. DOI: 10.2355/isijinternational.41.1053.
10.
TorresRCESánchezFHGonzálezAStudy of the kinetics of the recrystallization of cold rolled low-carbon steel. Metall Mater Trans A. 2002; 33A:25–31. DOI: 10.1007/s11661-002-0003-y.
11.
ShuQKlugJLMedeirosSLSCrystallization control for fluorine-free mold fluxes: effect of Na2O content on non-isothermal melt crystallization kinetics. ISIJ Int. 2020; 60:2425–2435. DOI: 10.2355/isijinternational.ISIJINT-2020-132.
CriadoJMSánchez-JiménezPEPérez-MaquedaLA.Critical study of the isoconversional methods of kinetic analysis. J Therm Anal Calorim. 2008; 92:199–203. DOI: 10.1007/s10973-007-8763-7.
14.
FriedmanHL.Kinetics of thermal degradation of char-forming plastics from thermogravimetry. Application to a phenolic plastic. J Polym Sci C. 1964; 6:183–195. DOI: 10.1002/polc.5070060121.
15.
LadKNSavaliaRTPratapAIsokinetic and isoconversional study of crystallization kinetics of a Zr-based metallic glass. Thermochim Acta. 2008; 473:74–80. DOI:10.1016/j.tca.2008.04.011.
16.
LiuQQianDHuaL.Transformation from non-isothermal to isothermal tempering of steel based on isoconversional method. J Mater Sci. 2018; 53:2774–2784. DOI: 10.1007/s10853-017-1680-7.
17.
Sente Software Ltd. (2021). JMatPro® [Internet] Guildford: Surrey Research Park [cited 2021 Dec 8]. Available from: https://www.sentesoftware.co.uk/.
18.
BourezgYIElfiadDAzzeddineHInvestigation of recrystallization kinetics in hot-rolled Mg-La alloy using differential scanning calorimetry technique. Thermochim Acta. 2020; 690. DOI: 10.1016/j.tca.2020.178688.
19.
RayRKJonasJJGuillénMPTransformation textures in steels. ISIJ Int. 1994; 34:927–942. DOI: 10.2355/isijinternational.34.927.
20.
TóthLSJonasJJDanielDDevelopment of ferrite rolling textures in low- and extra low-carbon steels. Metall Trans. 1990; 21A:2985–3000. DOI: 10.1007/BF02647219.
ChoiS-HChoJH.Primary recrystallization modelling for interstitial free steels. Mater Sci Eng A. 2005; 405:86–101. DOI: 10.1016/j.msea.2005.05.093.
23.
RajmohanNHayakawaYSzpunarJANeutron diffraction method for stored energy measurement in interstitial free steel. Acta Mater. 1997; 45:2485–2494. DOI: 10.1016/S1359-6454(96)00371-0.
24.
DiehlMKertschLTrakaKSite-specific quasi in situ investigation of primary static recrystallization in a low carbon steel. Mater Sci Eng A. 2019; 755:295–306. DOI:10.1016/j.msea.2019.02.032.
25.
OyarzabalMGuerenuAGutiérrezI.Effect of stored energy and recovery on the overall recrystallization kinetics of a cold rolled low carbon steel. Mater Sci Eng A. 2008; 485:200–209. DOI: 10.1016/j.msea.2007.07.077.
26.
AlanemeKKOkoteteEA.Recrystallization mechanisms and microstructure development in emerging metallic materials: A review. J Sci-Adv Mater Dev. 2019; 4:19–33. DOI: 10.1016/j.jsamd.2018.12.007.
27.
SeoM-DShiC-BWangHNon-isothermal melt crystallization of cuspidine in CaO–SiO2–CaF2 based glasses. J Non-Cryst Solids. 2015; 412:58–65. DOI: 10.1016/j.jnoncrysol.2015.01.008.
28.
UmarMQayyumFFarooqMUInvestigating the effect of cementite particles size and distribution on local stress and strain evolution in spheroidized medium carbon steel using crystal plasticity-based numerical simulations. Steel Res Int. 2021; 92:2000407. DOI: 10.1002/srin.202000407.
29.
QayyumFGukSPrahlU.Studying the damage evolution and the micro-mechanical response of X8CrMnNi16-6-6 TRIP steel matrix and 10% zirconia particle composite using a calibrated physics and crystal-plasticity-based numerical simulation model. Crystals (Basel). 2021; 11:759–778. DOI: 10.3390/cryst11070759.
30.
UmarMQayyumFFarooqMUQualitative investigation of damage initiation at meso-scale in Spheroidized C45EC steels by using crystal plasticity-based numerical simulations. J Compos Sci. 2021; 5:222–240. DOI: 10.3390/jcs5080222.
31.
SaitoGZhangTSakaguchiNIn-situ observation of abnormal grain growth in a low-alloyed carbon steel using SEM-EBSD. Mater. 2021; 15:100985. DOI: 10.1016/j.mtla.2020.100985.
32.
NaikSNWalleySM.The Hall-Petch and inverse Hall-Petch relations and the hardness of nanocrystalline metals. J Mater Sci. 2020; 55:2661–2681. DOI: 10.1007/s10853-019-04160-w.
33.
GarciaCIDeardoAJ.Formation of austenite in 1.5 Pct Mn steels. Metall Trans A. 1981; 12:521–530. DOI: 10.1007/BF02648551.
34.
RivaRMapelliCVenturiniR.Effect of coiling temperature on formability and mechanical properties of mild low carbon and HSLA steels processed by thin slab casting and direct rolling. ISIJ Int. 2007; 47:1204–1213. DOI: 10.2355/isijinternational.47.1204.
35.
MishraSDarmannC.Role and control of texture in deep-drawing steels. Int Met Rev. 1982; 27:307–320. DOI: 10.1179/imr.1982.27.1.307.
