Three TWIP steels based on the composition Fe-23Mn-3Si-3.3Al with different carbon concentrations were examined. The alloys were produced by rapid solidification in an experimental apparatus designed to simulate direct strip casting conditions. Examination of the driving force for solidification for this alloy showed the preference for BCC and FCC solidification were very close for this composition, within 10% of one another. This factor combined with the high undercooling resulted in the change in the primary solidified phase. Chemical analysis of the as-cast strip showed inter-dendritic segregation of Si and Al, but negligible segregation of Mn. A simple heat treatment was sufficient to chemically homogenise all alloys and produce microstructures comprising a fully austenitic structure, consistent with thermodynamic predictions.
BouazizOAllainSScottCHigh manganese austenitic twinning induced plasticity steels: a review of the microstructure properties relationships. Curr Opin Solid State Mater Sci. 2011; 15(4):141–168.
2.
De CoomanBCKwonOChinK-G.State-of-the-knowledge on TWIP steel. Mater Sci Technol. 2012; 28(5):513–527.
3.
ChenLKimJKKimSKStretch-flangeability of high Mn TWIP steel. Steel Res Int. 2010; 81(7):552–568.
4.
De CoomanBC.High Mn TWIP steel and medium Mn steel. In: Automotive steels. Sawston, United Kingdom: Woodhead Publishing; 2017. p. 317–385.
5.
FerryM.Direct strip casting of metals and alloys. Sawston, United Kingdom: Woodhead Pub.; 2006.
6.
HaoYLiJLiXInfluences of cooling rates on solidification and segregation characteristics of Fe-Cr-Ni-Mo-N super austenitic stainless steel. J Mater Process Technol. 2020; 275:116326.
7.
DorinTWoodKTaylorAEffect of coiling treatment on microstructural development and precipitate strengthening of a strip cast steel. Acta Mater. 2016; 115:167–177.
8.
RamajayamMStanfordN.Static recrystallisation of steels produced by direct strip casting – The effect of carbon and vanadium concentration. Mater Sci Eng A. 2016; 671:147–157.
9.
StrezovLHerbertsonJ.Experimental studies of interfacial heat transfer and initial solidification pertinent to strip casting. ISIJ Int. 1998; 38:959–966.
10.
EvansTStrezovL.Interfacial heat transfer and nucleation of steel on metallic substrates. Metall Mater Trans B. 2000; 31(5):1081–1089.
11.
GibsonIRosenDStruckerB.Directed energy deposition process. In: Additive manufacturing technology. Berlin: Springer; 2015. p. 245–268.
12.
Reed-HillREAbbaschianR.Physical metallurgy principles. New York: Van Nostrand; 1973.
13.
KraussG.Solidification, segregation, and banding in carbon and alloy steels. Metall Mater Trans B. 2003; 34(6):781–792.
14.
StrezovLHerbertsonJBeltonGR.Mechanisms of initial melt/substrate heat transfer pertinent to strip casting. Metall Mater Trans B. 2000; 31(5):1023–1030.
15.
HoneycombeRWKBhadeshiaHKDH.Steels: microstructure and properties. Oxford, United Kingdom: E. Arnold; 1981.
16.
MukunthanKHodgsonPDSellamuthuPCastability and microstructural development of iron-based alloys under conditions pertinent to strip casting–specialty Fe–Cr–Al alloys. ISIJ Int. 2013; 53(10):1803–1811.
17.
MalekjaniSTimokhinaIBWangJStatic recrystallization of strip cast alloys in the presence of complex nano-sulfide and nitride precipitates. Mater Sci Eng A. 2013; 581:39–47.
18.
MukunthanKHodgsonPDStrezovLSolidification behaviour and microstructural development of iron-based alloys under conditions pertinent to strip casting–200 series stainless steels. ISIJ Int. 2013; 53(12):2152–2159.
19.
BrooksJAThompsonAW.Microstructural development and solidification cracking susceptibility of austenitic stainless steel welds. Int Mater Rev. 1991; 36(1):16–44.
20.
SuutalaN.Effect of solidification conditions on the solidification mode in austenitic stainless steels. Metall Trans A. 1983; 14(1):191–197.
21.
ZachariaTDavidSVitekJHeat transfer during Nd: YAG pulsed laser welding and its effect on solidification structure of austenitic stainless steels. Metall Trans A. 1989; 20(5):957–967.
22.
FukumotoSKurzW.Prediction of the delta to gamma transition in austenitic stainless steels during laser treatment. ISIJ Int. 1998; 38(1):71–77.
23.
VitekJDasguptaADavidS.Microstructural modification of austenitic stainless steels by rapid solidification. Metall Trans A. 1983; 14(9):1833–1841.
