The role of C on microstructure and local chemical composition of an as-cast Ti42Al5Mn alloy was systematically characterised. Results show that C is enriched in α2, less dissolved in γ but depleted in βo phase. Crossing the C-solubility limit, approximately 0.3 at. %, leads to the precipitation of h-type carbides (Ti2AlC). Furthermore, a correlation between the lattice site preference and the C-solubility is rationalised by neutron powder diffraction technique, suggesting that Mn tends to substitute the position of Al site within the γ-phase (L10-lattice) with an occupancy rate of 4.31%. Consequently, fewer Ti6-type sites are formed where C is preferentially located. Finally, the interlamellar spacing and phase evolution as well as the preferential distribution of alloying elements are also evaluated.
YamaguchiM.High temperature intermetallics – with particular emphasis on TiAl. Mater Sci Technol. 1992; 8:299–307. https://doi.org/10.1179/mst.1992.8.4.299.
2.
KimYKimS.Advances in gammalloy materials-processes-application technology: successes, dilemmas, and future. JOM. 2018; 70:553–560. https://doi.org/10.1007/s11837-018-2747-x.
3.
ClemensHMayerS.Design, processing, microstructure, properties, and applications of advanced intermetallic TiAl alloys. Adv Eng Mater. 2013; 15:191–215. https://doi.org/10.1002/adem.201200231.
4.
SchwaighoferERashkovaBClemensHEffect of carbon addition on solidification behavior, phase evolutionand creep properties of an intermetallic β-stabilized γ-TiAl based alloy. Intermetallics. 2014; 46:173–184. https://doi.org/10.1016/j.intermet.2013.11.011.
5.
KleinTSchachermayerMMendez-MartinFCarbon distribution in multi-phase γ-TiAl based alloys and its influence on mechanical properties and phase formation. Acta Mater. 2015; 94:205–213. https://doi.org/10.1016/j.actamat.2015.04.055.
6.
WorthBJonesJAllisonJ.Creep deformation creep deformation in near-γTiAl: II. influence of carbon on in Ti-48Al-1V-0.3C. Metall Mater Trans A. 1995; 26:2961–2972. https://doi.org/10.1007/BF02669652.
7.
TianWNemotobM.Effect of carbon addition on the microstructures and mechanical properties of γ-TiAl alloys. Intermetcllics. 1997; 5:237–244. https://doi.org/10.1016/S0966-9795(96)00086-6.
8.
KimYKimS.Effects of microstructure and C and Si additions on elevated temperature creep and fatigue of gamma TiAl alloys. Intermetallics. 2014; 53:92–101. https://doi.org/10.1016/j.intermet.2014.04.006.
9.
KaradgeMGoumaPKimY.Precipitation strengthening in K5-series γ-TiAl alloyed with silicon and carbon. Metall Mater Trans A. 2003; 34:2129–2138. https://doi.org/10.1007/s11661-003-0277-8.
10.
TakeshiKMasayoshiTOsamuI.Effect of carbon and nitrogen on mechanical properties of TiAl alloys. ISIJ Int. 1991; 31:1161–1167. https://doi.org/10.2355/isijinternational.31.1161.
11.
WangQDingHZhangHVariations of microstructure and tensile property of γ-TiAl alloys with 0–0.5 at% C additives. Mater Sci Eng A. 2017; 700:198–208. https://doi.org/10.1016/j.msea.2017.06.019.
12.
ChlupováAHeczkoMObrtlíkKEffect of heat-treatment on the microstructure and fatigue properties of lamellar γ-TiAl alloyed with Nb, Mo and/or C. Mater Sci Eng A. 2020; 786:139427.
13.
WhittenbergerJRayR.Deformation properties of AlTi2C particle containing Ti-46Al-2Cr-2Nb alloys at 1000 to 1200 K. Scr Metall Mater. 1995; 33:1505–1512. https://doi.org/10.1016/0956-716X(95)00431-T.
14.
ParkHNamSKimNRefinement of the lamellar structure in TiAl-based intermetallic compound by addition of carbon. Scr Mater. 1999; 41:1197–1203. https://doi.org/10.1016/S1359-6462(99)00266-3.
15.
ParkHHwangSLeeCMicrostructural refinement and mechanical properties improvement of elemental powder metallurgy processed Ti-46.6Al-1.4Mn-2Mo alloy by carbon addition. Metall Mater Trans A. 2001; 32:251–259. https://doi.org/10.1007/s11661-001-0256-x.
16.
LiMXiaoSChenYThe effect of carbon addition on the high-temperature properties of β solidification TiAl alloys. J Alloys Compd. 2019; 775:441–448. https://doi.org/10.1016/j.jallcom.2018.09.397.
17.
FangHChenRGongXEffects of Nb on microstructure and mechanical properties of Ti42Al2.6C alloys. Adv Eng Mater. 2018; 20:1701112. https://doi.org/10.1002/adem.201701112.
18.
MenandAHuguetANérac-PartaixA.Interstitial solubility in γ and α2 phases of TiAl-based alloys. Acta Mater. 1996; 44:4729–4737. https://doi.org/10.1016/S1359-6454(96)00111-5.
19.
MenandAZapolsky-TatarenkoHNérac-PartaixA.Atom-probe investigations of TiAl alloys. Mater Sci Eng A. 1998; 250:55–64. https://doi.org/10.1016/S0921-5093(98)00536-X.
20.
ScheuCStergarESchoberMHigh carbon solubility in a γ-TiAl-based Ti-45Al-5Nb-0.5C alloy and its effect on hardening. Acta Mater. 2009; 57:1504–1511. https://doi.org/10.1016/j.actamat.2008.11.037.
21.
GerlingRSchimanskyFStarkAMicrostructure and mechanical properties of Ti 45Al 5Nb+(0–0.5C) sheets. Intermetallics. 2008; 16:689–697. https://doi.org/10.1016/j.intermet.2008.02.004.
22.
TetsuiTShindoKKobayashiSA newly developed hot worked TiAl alloy for blades and structural components. Scr Mater. 2002; 47:399–403. https://doi.org/10.1016/S1359-6462(02)00158-6.
23.
XuHLiXXingWProcessing map and hot working mechanism of as-cast Ti-42Al-5Mn alloy. Adv Eng Mater. 2018; 20:1701059), https://doi.org/10.1002/adem.201701059.
24.
XuHLiXXingXPhase transformation behavior of a Mn containing β-solidifying γ-TiAl alloy during continuous cooling. Intermetallics. 2018; 99:51–58. https://doi.org/10.1016/j.intermet.2018.05.004.
25.
LiXXuHXingWPhase transformation behavior of a β-solidifying γ-TiAl-based alloy from different phase regions with various cooling methods. Metals (Basel). 2018; 8:731), https://doi.org/10.3390/met8090731.
26.
YeLWangHZhouGPhase stability of TiAlX (X=V, Nb, Ta, Cr, Mo, W, and Mn) alloys. J Alloys Compd. 2020; 819:153291), https://doi.org/10.1016/j.jallcom.2019.153291.
27.
BandyopadhyayDSharmaRChakrabortiN.The Ti-Al-C system (titanium–aluminum–carbon). J Phase Equilib. 2000; 21:195–198. https://doi.org/10.1361/105497100770340273.
ChristophUAppelFWagnerR.Dislocation dynamics in carbon-doped titanium aluminide alloys. Mater Sci Eng A. 1997; 239-240:39–45. https://doi.org/10.1016/S0921-5093(97)00558-3.
31.
NemotoMTianWHaradaKMicrostructure of precipitation strengthened Ni3Al and TiAl. Mater Sci Eng A. 1992; 152:247–252.
32.
PerdrixFTrichetMBonnentienJRelationships between interstitial content, microstructure and mechanical properties in fully lamellar Ti-48Al alloys, with special reference to carbon. Intermetallics. 2001; 9:807–815. https://doi.org/10.1016/S0966-9795(01)00066-8.
33.
LiuZLinJLiSEffects of Nb and Al on the microstructures and mechanical properties of high Nb containing TiAl base alloys. Intermetallics. 2002; 10:653–659. https://doi.org/10.1016/S0966-9795(02)00037-7.
34.
SongYYangRLiDA first principles study of the influence of alloying elements on TiAl: site preference. Intermetallics. 2000; 8:563–568. https://doi.org/10.1016/S0966-9795(99)00164-8.
35.
RossouwCForwoodCGibsonMZone-axis convergent-beam electron diffraction and ALCHEMI analysis of Ti[sbnd]Al alloys with ternary additions. Phil Mag A. 1996; 74:77–102. https://doi.org/10.1080/01418619608239691.
36.
KastenhuberMKleinTClemensHTailoring microstructure and chemical composition of advanced γ-TiAl based alloys for improved creep resistance. Intermetallics. 2018; 97:27–33. https://doi.org/10.1016/j.intermet.2018.03.011.
37.
WuZHuRZhangTUnderstanding the role of carbon atoms on microstructure and phase transformation of high Nb containing TiAl alloys. Mater Charact. 2017; 124:1–7. https://doi.org/10.1016/j.matchar.2016.12.008.
38.
ChenSBeavenPWagnerR.Carbide precipitation in γ-TiAl alloys. Scr Metall Mater. 1992; 26:1205–1210. https://doi.org/10.1016/0956-716X(92)90564-U.
