Here, a novel cryogenic rolling plus intercritical annealing process was applied to a transformation-induced plasticity (TRIP) steel with a low chemical composition of carbon and manganese. Compared with traditional cold rolling, obvious grain refinement was observed, due to a high amount of dislocations retained. In addition, austenite volume fraction was increased, because of a unique nucleation mechanism. Subjected to cryogenic rolling, strength and ductility were increased, due to the enhanced austenite stability, which provided continuous and active TRIP effect. Consequently, tensile strength was increased to 1030 MPa, and elongation was increased to 38.2%. Thus, a great mechanical combination was obtained in a steel with a relatively low chemical composition with carbon and manganese, only by cryogenic rolling process.
CaoWQWangCShiJMicrostructure and mechanical properties of Fe-0.2C-5Mn steel processed by ART-annealing. Mater Sci Eng A. 2011; 564:501–508.
2.
GongPPalmiereEJRainforthWM.Thermomechanical processing route to achieve ultrafine grains in low carbon microalloyed steels. Acta Mater. 2016; 119:43–54. doi: 10.1016/j.actamat.2016.08.010
3.
CaoJYanJZhangJEffects of thermomechanical processing on microstructure and properties of bainitic work hardening steel. Mater Sci Eng A. 2015; 639:192–197. doi: 10.1016/j.msea.2015.05.005
4.
YanDTasanCCRaabeD.High resolution in situ mapping of microstrain and microstructure evolution reveals damage resistance criteria in dual phase steels. Acta Mater. 2015; 96:399–409. doi: 10.1016/j.actamat.2015.05.038
5.
SeoEJChoLEstrinYMicrostructure-mechanical properties relationships for quenching and partitioning (Q&P) processed steel. Acta Mater. 2016; 113:124–139. doi: 10.1016/j.actamat.2016.04.048
EdmondsDVHeKRizzoFCQuenching and partitioning martensite-a novel steel heat treatment. Mater Sci Eng A. 2006; 438-440:25–34. doi: 10.1016/j.msea.2006.02.133
8.
YiHLGhoshSKLiuWJNonequilibrium solidification and ferrite in d-TRIP steel. Mater Sci Technol. 2010; 26(7):817–823. doi: 10.1179/174328409X428918
9.
ZhaoJJiangZLeeCS.Effects of tungsten addition and heat treatment conditions on microstructure and mechanical properties of microalloyed forging steels. Mater Sci Eng A. 2013; 562:144–151. doi: 10.1016/j.msea.2012.11.006
10.
LeeYKHanJ.Current opinion in medium manganese steel. Mater Sci Technol. 2015; 31:843–856. doi: 10.1179/1743284714Y.0000000722
11.
NakadaNMizutaniKTsuchiyamaTDifference in transformation behavior between ferrite and austenite formations in medium manganese steel. Acta Mater. 2014; 65:251–258. doi: 10.1016/j.actamat.2013.10.067
12.
MaY.Medium-manganese steels processed by austenite-reverted-transformation annealing for automotive applications. Mater Sci Technol. 2017; 33:1713–1727. doi: 10.1080/02670836.2017.1312208
13.
LuoLBLiWWangLTensile behaviors and deformation mechanism of a medium Mn-TRIP steel at different temperatures. Mater Sci Eng A. 2017; 682:698–703. doi: 10.1016/j.msea.2016.11.017
14.
SugimotoKNakanoKSongSMRetained austenite characteristics and stretch-flange ability of high strength low alloy TRIP type bainitic sheet steel. ISIJ Int. 2002; 42:450–455. doi: 10.2355/isijinternational.42.450
15.
GiraultEJacquesPRatchevP.Study of the temperature dependence of the bainitic transformation rate in a multiphase TRIP-assisted steel. Mater Sci Eng A. 1999; 273-275:471–474. doi: 10.1016/S0921-5093(99)00330-5
16.
HanJLeeSJJungJGThe effects of the initial martensite microstructure on the microstructure and tensile properties of intercritically annealed Fe-9Mn-0.05C steel. Acta Mater. 2014; 78:369–377. doi: 10.1016/j.actamat.2014.07.005
17.
SuhDWParkPJLeeTHInfluence of Al on the microstructural evolution and mechanical behavior of low-carbon, manganese transformation-induced-plasticity steel. Metall Mater Trans A. 2010; 41:397–408. doi: 10.1007/s11661-009-0124-7
18.
BhattacharyyaTSinghSBDasSDevelopment and characterisation of C-Mn-Al-Si-Nb TRIP aided steel. Mater Sci Eng A. 2011; 528:2394–2400. doi: 10.1016/j.msea.2010.11.054
19.
XuNCavallaroGPGersonAR.Synchrotron micro-diffraction analysis of the microstructure of cryogenically treated high performance tool steel prior to and after tempering. Mater Sci Eng A. 2010; 527:6822–6830. doi: 10.1016/j.msea.2010.06.072
20.
LiSMinNDengLInfluence of deep cryogenic treatment on internal friction behavior in the process of tempering. Mater Sci Eng A. 2011; 528:1247–1250. doi: 10.1016/j.msea.2010.10.012
21.
TyshchenkoATheisenWOppenko wskiALow-temperature martensitic transformation and deep cryogenic treatment of a tool steel. Mate Sci Eng A. 2010; 527:7027–7039. doi: 10.1016/j.msea.2010.07.056
22.
LeeSJShinSKwonMYTensile properties of medium Mn steel with a bimodal UFG α+γ coarse δ-ferrite microstructure. Metall Mater Trans A. 2017; 48:1678–1700. doi: 10.1007/s11661-017-3979-z
23.
HanJLeeY-K.The effects of the heating rate on the reverse transformation mechanism and the phase stability of reverted austenite in medium Mn steels. Acta Mater. 2014; 67:354–361. doi: 10.1016/j.actamat.2013.12.038
24.
LuoHLiuJDongH.A novel observation on cementite formed during intercritical annealing of medium Mn steel. Metall Mater Trans A. 2016; 47:3119–3124. doi: 10.1007/s11661-016-3448-0
25.
XuYBHuZPZouYEffect of two-step intercritical annealing on microstructure and mechanical properties of hot-rolled medium manganese TRIP steel containing δ-ferrite. Mater Sci Eng A. 2017; 688:40–55. doi: 10.1016/j.msea.2017.01.063
26.
HuyanFYanJ-YHöglundLSimulation of the growth of austenite from as-quenched martensite in medium Mn steels. Metall Mater Trans A. 2018; 49:1053–1060. doi: 10.1007/s11661-018-4497-3
27.
LuoHWDongH.New ultrahigh-strength Mn-alloyed TRIP steels with improved formability manufactured by intercritical annealing. Mater Sci Eng A. 2015; 626:207–212. doi: 10.1016/j.msea.2014.12.049
28.
ShiJSunXWangMEnhanced work-hardening behavior and mechanical properties in ultrafine-grained steels with large-fractioned metastable austenite. Scr Mater. 2010; 63:815–818. doi: 10.1016/j.scriptamat.2010.06.023
29.
CaiZHDingHMisraRDKUnique impact of ferrite in influencing austenite stability and deformation behavior in a hot-rolled Fe-Mn-Al-C steel. Mater Sci Eng A. 2014; 595:86–91. doi: 10.1016/j.msea.2013.12.003
30.
HuBLuoH.A novel two-step intercritical annealing process to improve mechanical properties of medium Mn steel. Acta Mater. 2019; 176:250–263. doi: 10.1016/j.actamat.2019.07.014
31.
LuoHShiJWangCExperimental and numerical analysis on formation of stable austenite during the intercritical annealing of 5Mn steel. Acta Mater. 2011; 59:4002–4014. doi: 10.1016/j.actamat.2011.03.025
