The effects of hot rolling and homogenisation treatment on the microstructure and mechanical properties of low-alloy transformation-induced plasticity (TRIP) steel were studied. With increasing the reduction in thickness during rolling, the band spacing and the average ferrite grain size decreased with the consequent enhancement of mechanical properties. Homogenisation treatment resulted in the gradual fading of the banded morphology, more homogeneous microhardness profile, and twice total elongation compared to the as-cast counterpart. The experimentally observed homogenisation time judged by the disappearance of the banded structure was in agreement with the obtained values based on the band spacing and elemental analysis. This work provided scientific evidence for the assumptions used to derive the homogenisation formulae.
ChiangJBoydJDPilkeyAK.Effect of microstructure on retained austenite stability and tensile behaviour in an aluminum-alloyed TRIP steel. Mater SciEng: A. 2015; 638:132–142.
2.
DeldarSMirzadehHParsaMH.Prevention of surface hot shortness, development of banded structure, and mechanical properties of hot rolled Cu-bearing steel. Eng Fail Anal. 2016; 68:132–137. doi: 10.1016/j.engfailanal.2016.06.001
3.
KheiriSMirzadehHNaghizadehM.Tailoring the microstructure and mechanical properties of AISI 316L austenitic stainless steel via cold rolling and reversion annealing. Mater Sci Eng: A. 2019; 759:90–96. doi: 10.1016/j.msea.2019.05.028
4.
SohrabiMJMirzadehHDehghanianC.Thermodynamics basis of saturation of martensite content during reversion annealing of cold rolled metastable austenitic steel. Vacuum. 2020; 174:109220. doi: 10.1016/j.vacuum.2020.109220
5.
AziziGMirzadehHParsaMH.The effect of primary thermo-mechanical treatment on TRIP steel microstructure and mechanical properties. Mater Sci Eng: A. 2015; 639:402–406. doi: 10.1016/j.msea.2015.05.045
6.
LeeKRyuJHLeeSWInfluence of the initial microstructure on the heat treatment response and tensile properties of TRIP-assisted steel. Metall Mater Trans A. 2016; 47:5259–5265. doi: 10.1007/s11661-016-3699-9
7.
ThompsonSWHowellPR.Factors influencing ferrite/pearlite banding and origin of large pearlite nodules in a hypoeutectoid plate steel. Mater Sci Technol. 1992; 8:777–784. doi: 10.1179/mst.1992.8.9.777
8.
KraussG.Solidification, segregation, and banding in carbon and alloy steels. Metall Mater Trans B. 2003; 34:781–792. doi: 10.1007/s11663-003-0084-z
9.
KhalidFAFarooqueMUl HaqARole of ferrite/pearlite banded structure and segregation on mechanical properties of microalloyed hot rolled steel. Mater Sci Technol. 1999; 15:1209–1215. doi: 10.1179/026708399101505121
10.
WangHKangJDouWMicrostructure and mechanical properties of hot-rolled and heat-treated TRIP steel with direct quenching process. Mater Sci Eng: A. 2017; 702:350–359. doi: 10.1016/j.msea.2017.07.039
11.
AlibeykiMMirzadehHNajafiMModification of rule of mixtures for estimation of the mechanical properties of dual-phase steel. J Mater Eng Perform. 2017; 26:2683–2688. doi: 10.1007/s11665-017-2687-6
12.
ZhangYChenWQChenLHomogenisation of 20SiMn2MoV steel ingots: thermodynamic/kinetic simulation and experimental validation. Mater High Temp. 2015; 32:412–418. doi: 10.1179/1878641314Y.0000000032
13.
AziziGMirzadehHParsaMH.Unraveling the effect of homogenization treatment on decomposition of austenite and mechanical properties of low-alloyed TRIP steel. Steel Res Int. 2016; 87:820–823. doi: 10.1002/srin.201500246
14.
LynchPCGrimmTJ.Reducing microsegregation in next-generation high-strength low-alloy cast steels. Int J Metalcast. 2019; 13:783–792. doi: 10.1007/s40962-019-00321-4
15.
SunQYWangLPLiuDREffects of double-procedure homogenization heat treatment on microstructure and mechanical properties of WE43A alloy. Mater Res Express. 2018; 5:086517. doi: 10.1088/2053-1591/aad31d
16.
PourbahariBMirzadehHEmamyM.Elucidating the effect of intermetallic compounds on the behavior of Mg-Gd-Al-Zn magnesium alloys at elevated temperatures. J Mater Res. 2017; 32:4186–4195. doi: 10.1557/jmr.2017.415
17.
LinYCLuoSCYinLXMicrostructural evolution and high temperature flow behaviors of a homogenized Sr-modified Al-Si-Mg alloy. J Alloys Compd. 2018; 739:590–599. doi: 10.1016/j.jallcom.2017.12.278
18.
WongWHadadzadehABenoitMJImpact of homogenization heat treatment on the high temperature deformation behavior of cast AZ31B magnesium alloy. J Mater Process Technol. 2018; 254:238–247. doi: 10.1016/j.jmatprotec.2017.11.039
19.
JuckenSSchaalETougasBImpact of a post-casting homogenization treatment on the high-temperature oxidation resistance of a Cu-Ni-Fe alloy. Corros Sci. 2019; 147:321–329. doi: 10.1016/j.corsci.2018.11.037
20.
SadeghiIWellsMAEsmaeiliS.Effect of particle shape and size distribution on the dissolution behavior of Al2Cu particles during homogenization in aluminum casting alloy Al-Si-Cu-Mg. J Mater Process Technol. 2018; 251:232–240. doi: 10.1016/j.jmatprotec.2017.08.042
21.
SohrabiMJMirzadehH.Estimation of homogenisation time for superalloys based on a new diffusional model. Mater Sci Technol. 2020; 36:380–384. doi: 10.1080/02670836.2019.1706906
22.
ReitzJWietbrockBRichterSEnhanced homogenization strategy by electroslag remelting of high-manganese TRIP and TWIP steels. Adv Eng Mater. 2011; 13:395–399. doi: 10.1002/adem.201000322
23.
HanYLiCRenJDendrite segregation changes in high temperature homogenization process of As-cast H13 steel. ISIJ Int. 2019; 59:1893–1900. doi: 10.2355/isijinternational.ISIJINT-2019-148
24.
LeslieWC.The physical metallurgy of steels. New York: McGraw-Hill; 1982.
25.
ChiangJLawrenceBBoydJDEffect of microstructure on retained austenite stability and work hardening of TRIP steels. Mater Sci Eng: A. 2011; 528:4516–4521. doi: 10.1016/j.msea.2011.02.032
26.
XiePHanMWuCLA high-performance TRIP steel enhanced by ultrafine grains and hardening precipitates. Mater Des. 2017; 127:1–7. doi: 10.1016/j.matdes.2017.04.063
27.
GhaemifarSMirzadehH.Refinement of banded structure via thermal cycling and its effects on mechanical properties of dual phase steel. Steel Res Int. 2018; 89:1700531. doi: 10.1002/srin.201700531
28.
KalhorAMirzadehH.Tailoring the microstructure and mechanical properties of dual phase steel based on the initial microstructure. Steel Res Int. 2017; 88:1600385. doi: 10.1002/srin.201600385
29.
SohrabiMJMirzadehHRafieiM.Solidification behavior and Laves phase dissolution during homogenization heat treatment of Inconel 718 superalloy. Vacuum. 2018; 154:235–243. doi: 10.1016/j.vacuum.2018.05.019
30.
PorterDAEasterlingKESherifMY.Phase transformations in metals and alloys. 3rd ed.Boca Raton: CRC Press; 2009.
31.
SohrabiMJMirzadehH.Numerical and analytical solutions for determination of interdiffusion coefficients in superalloys during homogenization. Mater Today Commun. 2019; 21:100631. doi: 10.1016/j.mtcomm.2019.100631
32.
MirzadehHAlibeykiMNajafiM.Unraveling the initial microstructure effects on mechanical properties and work-hardening capacity of dual phase steel. Metall Mater Trans A. 2017; 48:4565–4573. doi: 10.1007/s11661-017-4246-z
33.
CalvilloPRHernandez-ExpositoABoulaajajAHot deformation and ductility analysis of continuous cast C40 steel by means of tensile and compression tests. Mater Sci Forum. 2010; 638–642:3152–3157. doi: 10.4028/www.scientific.net/MSF.638-642.3152
34.
SoleimaniMMirzadehHDehghanianC.Effect of grain size on the corrosion resistance of low carbon steel. Mater Res Express. 2020; 7:016522. doi: 10.1088/2053-1591/ab62fa
35.
TejedorREdalatiKBenitoJAHigh-pressure torsion of iron with various purity levels and validation of Hall-Petch strengthening mechanism. Mater Sci Eng: A. 2019; 743:597–605. doi: 10.1016/j.msea.2018.11.127
36.
MahalleGKotkundeNGuptaAKMicrostructure characteristics and comparative analysis of constitutive models for flow stress prediction of Inconel 718 alloy. J Mater Eng Perform. 2019; 28:3320–3331. doi: 10.1007/s11665-019-04116-w
37.
PourbahariBMirzadehHEmamyM.The effects of grain refinement and rare earth intermetallics on mechanical properties of as-cast and wrought magnesium alloys. J Mater Eng Perform. 2018; 27:1327–1333. doi: 10.1007/s11665-018-3238-5
38.
LiuMYShiBWangCNormal Hall–Petch behavior of mild steel with submicron grains. Mater Lett. 2003; 57:2798–2802. doi: 10.1016/S0167-577X(02)01377-0
39.
SoleimaniMMirzadehHDehghanianC.Processing route effects on the mechanical and corrosion properties of dual phase steel. Met Mater Int. in press. doi:10.1007/s12540-019-00459-0.
40.
ZamaniRMirzadehHEmamyM.Mechanical properties of a hot deformed Al-Mg2Si in-situ composite. Mater Sci Eng: A. 2018; 726:10–17. doi: 10.1016/j.msea.2018.04.064
