Directionally solidified Mg-4wt-% Zn alloy was prepared and the effect of growth rate on its microstructure evolution and mechanical properties was investigated. A typical cellular structure was observed when the growth rate was lower than 60 µm s−1. The microstructure evolved from cell to columnar dendrite as the growth rate increased. The ultimate tensile strength of the directionally solidified alloy was found to be higher than that of the alloy ingot with the same cooling rate. The ultimate tensile strength of the directionally solidified alloy increased with increasing growth rate but it decreased during the cell–dendrite transition. The results indicate that the mechanical properties of the directionally solidified alloy with fine cellular and columnar dendritic structures meet the requirements of biomaterials.
EsmailyM, SvenssonJE, FajardoS, Fundamentals and advances in magnesium alloy corrosion. Prog Mater Sci. 2017;89:92–193. doi: 10.1016/j.pmatsci.2017.04.011
3.
TahmasebifarA, KayhanSM, EvisZ, Mechanical, electrochemical and biocompatibility evaluation of AZ91D magnesium alloy as a biomaterial. J Alloys Compd. 2016;687:906–919. doi: 10.1016/j.jallcom.2016.05.256
4.
JandaghiMR, PouraliakbarH, Gharah ShiranMK, On the effect of non-isothermal annealing and multi-directional forging on the microstructural evolutions and correlated mechanical and electrical characteristics of hot-deformed Al-Mg alloy. Mater Sci Eng A. 2016;657:431–440. doi: 10.1016/j.msea.2016.01.056
5.
ZhaoMC, LiuM, SongG, Influence of the β-phase morphology on the corrosion of the Mg alloy AZ91. Corros Sci. 2008;50(7):1939–1953. doi: 10.1016/j.corsci.2008.04.010
6.
ZhangX, YuanG, MaoL, Biocorrosion properties of as-extruded Mg-Nd-Zn-Zr alloy compared with commercial AZ31 and WE43 alloys. Mater Lett. 2012;66(1):209–211. doi: 10.1016/j.matlet.2011.08.079
7.
RezaJM, HesamP.Elucidating the microscopic origin of electrochemical corrosion and electrical conductivity by lattice response to severe plastic deformation in Al-Mn-Si alloy. Mater Res Bull. 2018;108:195–206. doi: 10.1016/j.materresbull.2018.09.011
8.
CrimuC, StanciuS, CristeaDP, Microbiological testing of biodegradable Mg-Ca alloys for use in orthopedic implants. Adv Mat Res. 2014;1036:195–200.
9.
ZhengYF, GuXN, WitteF.Biodegradable metals. Mater Sci Eng R. 2014;77:1–34. doi: 10.1016/j.mser.2014.01.001
10.
JiaHM, FengXH, YangYS.Microstructure and corrosion resistance of directionally solidified Mg-2wt-%Zn alloy. Corros Sci. 2017;120:75–81. doi: 10.1016/j.corsci.2017.02.023
11.
ZhangC, MaD, WuKS, Microstructure and microsegregation in directionally solidified Mg-4Al alloy. Intermetallics. 2007;15(10):1395–1400. doi: 10.1016/j.intermet.2007.01.009
12.
ZhengX, LuoAA, ZhangC, Directional solidification and microsegregation in a magnesium-aluminium-calcium alloy. Metall Mater Trans A. 2012;43(9):3239–3248. doi: 10.1007/s11661-012-1159-8
13.
MirkovićD, Schmid-FetzerR.Directional solidification of Mg-Al alloys and microsegregation study of Mg alloys AZ31 and AM50: Part I. Methodology. Metall Mater Trans A. 2009;40(4):958–973. doi: 10.1007/s11661-009-9787-3
14.
MirkovićD, Schmid-FetzerR.Directional solidification of Mg-Al alloys and microsegregation study of Mg alloys AZ31 and AM50: Part II. comparison between AZ31 and AM50. Metall Mater Trans A. 2009;40(4):974–981. doi: 10.1007/s11661-009-9788-2
15.
WangJH, YangGY, LiuSJ, Microstructure and room temperature mechanical properties of directionally solidified Mg-2.35Gd magnesium alloy. Trans Nonferr Metal Soc China. 2016;26(5):1294–1300. doi: 10.1016/S1003-6326(16)64231-0
16.
JiaHM, FengXH, YangYS.Microstructure of directionally solidified Mg-Zn alloy with different growth rates. Mater Sci Forum. 2015;816:411–447. doi: 10.4028/www.scientific.net/MSF.816.411
17.
KurzW, FisherDJ.Fundamental of solidification. 4th revised ed.Tran Tech Publications Ltd; 2010. p. 39–50.
18.
WangS, LiuD, DuY, Development of an atomic mobility database for liquid phase in multicomponent Al alloys: focusing on binary systems. Int J Mater Res. 2013;104(8):721–735. doi: 10.3139/146.110923
19.
Meng-WuWU, XiongSM.Modeling of equiaxed and columnar dendritic growth of magnesium alloy. Trans Nonferr Metal Soc China. 2012;22(9):2212–2219. doi: 10.1016/S1003-6326(11)61451-9
20.
PouraliakbarHA, JandaghiMR.Mechanistic insight into the role of severe plastic deformation and post-deformation annealing in fracture behavior of Al-Mn-Si alloy. Mech Mater. 2018;122:145–158. doi: 10.1016/j.mechmat.2018.04.002
21.
PouraliakbarH, PakbazM, FiroozS, Study on the dynamic and static softening phenomena in Al-6Mg alloy during two-stage deformation through interrupted hot compression test. Measurement. 2016;77:50–53. doi: 10.1016/j.measurement.2015.08.033
22.
LiuS, YangG, XiaoL, Effects of the growth rate on microstructures and room temperature mechanical properties of directionally solidified Mg-5.2Zn alloy. JOM. 2016;68(12):1–10. doi: 10.1007/s11837-016-1965-3
23.
LuoS, YangG, LiuS, Microstructure evolution and mechanical properties of directionally solidified Mg- xGd (x = 0.8, 1.5 and 2.5) alloys. Mater Sci Eng A. 2016;662:241–250. doi: 10.1016/j.msea.2016.03.065
24.
YangG, LuoS, LiuS, Microstructural evolution, phase constitution and mechanical properties of directionally solidified Mg-5.5Zn-xGd (x = 0.8, 2.0 and 4.0) alloys. J Alloys Compd. 2017;725:145–154. doi: 10.1016/j.jallcom.2017.05.129
25.
ErincM, SillekensWH, MannensR, Applicability of existing magnesium alloys as biomedical implant materials. Magnes Technol. 2009;8:209–214.
26.
ZengRC, SunL, ZhengYF, Corrosion and characterization of dual phase Mg-Li-Ca alloy in Hank's solution: The influence of microstructural features. Corros Sci. 2014;79(79):69–82. doi: 10.1016/j.corsci.2013.10.028
27.
PengQ, HuangY, KainerKU, Development of high performance single-phase solid solution magnesium alloy at low temperature. Adv Eng Mater. 2012;14(3):178–184. doi: 10.1002/adem.201100176
28.
BrarHS, WongJ, ManuelMV.Investigation of the mechanical and degradation properties of Mg-Sr and Mg-Zn-Sr alloys for use as potential biodegradable implant materials. J Mech Behav Biomed Mater. 2012;7(3):87–95. doi: 10.1016/j.jmbbm.2011.07.018
29.
HortN, HuangY, FechnerD, Magnesium alloys as implant materials-principles of property design for Mg-RE alloys. Acta Biomater. 2010;6(5):1714–1725. doi: 10.1016/j.actbio.2009.09.010
30.
ZhangB, HouY, WangX, Mechanical properties, degradation performance and cytotoxicity of Mg-Zn-Ca biomedical alloys with different compositions. Mater Sci Eng C. 2011;31(8):1667–1673. doi: 10.1016/j.msec.2011.07.015
31.
ZhangE, YangL, XuJ, Microstructure, mechanical properties and bio-corrosion properties of Mg-Si(-Ca, Zn) alloy for biomedical application. Acta Biomater. 2010;6(5):1756–1762. doi: 10.1016/j.actbio.2009.11.024
32.
LiT, HeY, ZhangH, Microstructure, mechanical property and in vitro biocorrosion behavior of single-phase biodegradable Mg-1.5Zn-0.6Zr alloy. J Magnes Alloys. 2014;2(2):181–189. doi: 10.1016/j.jma.2014.05.006
