In this study, a β-Ta2O5 coating was deposited onto a Ti–6Al–4V substrate using a double-cathode glow discharge plasma technique. The hardness and elastic modulus values of the β-Ta2O5 coating were almost 4 times and 1.8 times greater than that of the Ti–6Al–4V substrate, respectively. Potentiodynamic polarisation curves indicated that the current densities of the β-Ta2O5 coated sample are least one order of magnitude less than that observed for the uncoated substrate under a solid/liquid slurry flow. Electrochemical impedance spectroscopy results showed that the resistance values for the β-Ta2O5 coating are of the order of 106 Ω cm2, and at the same erosion time, the resistance value for the β-Ta2O5 coating is one order of magnitude greater than that of the Ti–6Al–4V.
BursteinGT, SasakiK.The birth of corrosion pits as stimulated by slurry erosion. Corros Sci. 2000;42(5):841–860.
2.
ZhengZB, ZhengYG, SunWH, Erosion–corrosion of HVOF-sprayed Fe-based amorphous metallic coating under impingement by a sand-containing NaCl solution. Corros Sci. 2013;76:337–347.
3.
WangY, XingZZ, LuoQ, Corrosion and erosion–corrosion behaviour of activated combustion high-velocity air fuel sprayed Fe-based amorphous coatings in chloride-containing solutions. Corros Sci. 2015;98:339–353.
4.
GiourntasL, HodgkiessT, GallowayAM.Comparative study of erosion–corrosion performance on a range of stainless steels. Wear. 2015;332–333:1051–1058.
5.
SouzaVAD, NevilleA.Corrosion and synergy in a WCCoCr HVOF thermal spray coating—understanding their role in erosion–corrosion degradation. Wear. 2005;259(1):171–180.
6.
MonticelliC, ZucchiF, TampieriA.Triboelectrochemical behaviour of a Si3N4–TiN ceramic composite and a titanium alloy commonly used in biomedical applications. Wear. 2009;266(1):327–336.
7.
LutfullinRY, KruglovAA, SafiullinRV, Processing properties of nano- and submicro-crystalline Ti–6Al–4V titanium alloy. Mater Sci Eng A. 2009;503(1):52–54.
8.
YazdiR, Kashani-BozorgSF.Microstructure and wear of in-situ Ti/(TiN + TiB) hybrid composite layers produced using liquid phase process. Mater Chem Phys. 2015;152:147–157.
9.
KhayatanN, GhasemiHM, AbediniM.Synergistic erosion-corrosion behavior of commercially pure titanium at various impingement angles. Wear. 2017;380–381:154–162.
10.
KuromotoNK, SimãoRA, SoaresGA.Titanium oxide films produced on commercially pure titanium by anodic oxidation with different voltages. Mater Charact. 2007;58(2):114–121.
11.
MengH, HuX, NevilleA.A systematic erosion– corrosion study of two stainless steels in marine conditions via experimental design. Wear. 2007;263(1):355–362.
12.
LindgrenM, PerolainenJ.Slurry pot investigation of the influence of erodent characteristics on the erosion resistance of austenitic and duplex stainless steel grades. Wear. 2014;319(1):38–48.
13.
MišinaM, MusilJ, KadlecS.Composite TiN–Ni thin films deposited by reactive magnetron sputter ion-plating. Surf Coat Technol. 1998;110(3):168–172.
14.
BagheryP, FarzamM, MousaviAB, Ni–TiO2 nanocomposite coating with high resistance to corrosion and wear. Surf Coat Technol. 2010;204(23):3804–3810.
15.
WangZX, WuHR, ShanXL, Microstructure and erosive wear behaviors of Ti6Al4V alloy treated by plasma Ni alloying. Appl Surf Sci. 2016;388:510–516.
16.
LengYX, ChenJY, YangP, The biocompatibility of the tantalum and tantalum oxide films synthesized by pulse metal vacuum arc source deposition. Nucl Instrum Methods Phys Res B. 2006;242(1):30–32.
17.
AtanassovaE, LytvynP, DubSN, Nanomechanical properties of pure and doped Ta2O5 and the effect of microwave irradiation. J Phys D. 2012;45(47):475304.
18.
DíazB, ŚwiatowskaJ, MauriceV, Chromium and tantalum oxide nanocoatings prepared by filtered cathodic arc deposition for corrosion protection of carbon steel. Surf Coat Technol. 2012;206(19):3903–3910.
19.
HuW, XuJ, LuX, Corrosion and wear behaviours of a reactive-sputter-deposited Ta2O5 nanoceramic coating. Appl Surf Sci. 2016;368:177–190.
20.
XuJ, HuW, XieZ, Reactive-sputter-deposited β-Ta2O5 and TaON nanoceramic coatings on Ti-6Al-4V alloy against wear and corrosion damage. Surf Coat Technol. 2016;296:171–184.
21.
OliverWC, PharrGMJ.An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J Mater Res. 1992;7(6):1564–1583.
22.
XuJ, ZhuoC, HanD, Erosion–corrosion behavior of nano-particle-reinforced Ni matrix composite alloying layer by duplex surface treatment in aqueous slurry environment. Corros Sci. 2009;51(5):1055–1068.
23.
DíazB, ŚwiatowskaJ, MauriceV, Tantalum oxide nanocoatings prepared by atomic layer and filtered cathodic arc deposition for corrosion protection of steel: comparative surface and electrochemical analysis. Electrochim Acta. 2013;90:232–245.
24.
LiY, ZhaoT, WeiS, Effect of Ta2O5/TiO2 thin film on mechanical properties, corrosion and cell behavior of the NiTi alloy implanted with tantalum. Mater Sci Eng, C. 2010;30(8):1227–1235.
25.
YaoZ, JiangZ, XinS, Electrochemical impedance spectroscopy of ceramic coatings on Ti–6Al–4V by micro-plasma oxidation. Electrochim Acta. 2005;50(16):3273–3279.
26.
AtanassovaE, SpassovD.X-ray photoelectron spectroscopy of thermal thin Ta2O5 films on Si. Appl Surf Sci. 1998;135(1):71–82.
27.
LeeKS, WuttiphanS, HuXZ, Contact-induced transverse fractures in brittle layers on soft substrates: a study on silicon nitride bilayers. J Am Ceram Soc. 2010;81(3):571–580.
28.
BhowmickS, KaleAN, JayaramV, Contact damage in TiN coatings on steel. Thin Solid Films. 2003;436(2):250–258.
29.
ChenL, BaiSL.The anti-corrosion behavior under multi-factor impingement of Hastelloy C22 coating prepared by multilayer laser cladding. Appl Surf Sci. 2018;437:1–12.
30.
MirandaDA, JaimesSA, BastidasJM.Assessment of carbon steel microbiologically induced corrosion by electrical impedance spectroscopy. J Solid State Electrochem. 2014;18(2):389–398.
31.
ShengH, WuY, GaoW, Slurry erosion-corrosion resistance and microbial corrosion electrochemical characteristics of HVOF sprayed WC-10Co-4Cr coating for offshore hydraulic machinery. Int J Refract Met Hard Mater. 2018;74:7–13.
32.
BoseS, PathakLC, SinghR.Response of boride coating on the Ti-6Al-4V alloy to corrosion and fretting corrosion behavior in Ringer's solution for bio-implant application. Appl Surf Sci. 2018;433:1158–1174.
33.
RylJ, WysockaJ, SlepskiP, Instantaneous impedance monitoring of synergistic effect between cavitation erosion and corrosion processes. Electrochim Acta. 2016;203:388–395.
34.
JorcinJB, OrazemME, PébèreN, CPE analysis by local electrochemical impedance spectroscopy. Electrochim Acta. 2006;51(8):1473–1479.
35.
YaoZ, JiangZ, WangF.Study on corrosion resistance and roughness of micro-plasma oxidation ceramic coatings on Ti alloy by EIS technique. Electrochim Acta. 2007;52(13):4539–4546.
36.
LindgrenM, PerolainenJ.Slurry pot investigation of the influence of erodant characteristics on the erosion resistance of titanium. Wear. 2014;321:64–69.
37.
HuX, NevilleA.The electrochemical response of stainless steels in liquid–solid impingement. Wear. 2005;258(1):641–648.
38.
StackMM, PurandareY, HovsepianP.Impact angle effects on the erosion–corrosion of superlattice CrN/NbN PVD coatings. Surf Coat Technol. 2004;188-189:556–565.
39.
PurandareYP, StackMM, HovsepianPE.Velocity effects on erosion–corrosion of CrN/NbN “superlattice” PVD coatings. Surf Coat Technol. 2006;201(1):361–370.
40.
WangHW, StackMM, LyonSB, The corrosion behaviour of macroparticle defects in arc bond-sputtered CrN/NbN superlattice coatings. Surf Coat Technol. 2000;126(2):279–287.
41.
Alegría-OrtegaJA, Ocampo-CarmonaLM, Suárez-BustamanteFA, Erosion–corrosion wear of Cr/CrN multi-layer coating deposited on AISI-304 stainless steel using the unbalanced magnetron (UBM) sputtering system. Wear. 2012;290-291:149–153.
42.
StackMM.Abd El Badia TM. mapping erosion–corrosion of WC/Co–Cr based composite coatings: particle velocity and applied potential effects. Surf Coat Technol. 2006;201(3):1335–1347.
