This paper investigates the effect of post-deposition heat treatment on porosity, microstructure, and mechanical properties of Ti–6Al–4V produced via an Electron Beam Melting process. Samples were studied in the conditions of as-built and heat treated at 920°C and 1030°C. The as-built samples were characterised by columnar β grains consists of α+β microstructure with Widmanstätten and colony morphologies were found. Heat treatment resulted in increased α lath width. The yield strength and ultimate tensile strength was greater in the as-built condition than wrought material. Porosity re-growth occurred after heat treatment but it did not affect the tensile properties. Greater ductility after heat treatment was attributed to the larger α lath width which increases effective slip length.
LutjeringG, WilliamsJ.Titanium. 2nd ed. New York: Springer; 2007.
2.
AntonysamyAA, MeyerJ, PrangnellPB.Effect of build geometry on the β-grain structure and texture in additive manufacture of Ti6Al4 V by selective electron beam melting. Mater Charact. 2013;84:153–168. doi: 10.1016/j.matchar.2013.07.012
3.
SafdarA, WeiLY, SnisA, Evaluation of microstructural development in electron beam melted Ti-6Al-4 V. Mater Charact. 2012;65:8–15. doi: 10.1016/j.matchar.2011.12.008
4.
Al-BermaniSS, BlackmoreML, ZhangW, The origin of microstructural diversity, texture, and mechanical properties in electron beam melted Ti-6Al-4 V. Metall Mater Trans A. 2010;41:3422–3434. doi: 10.1007/s11661-010-0397-x
5.
HrabeN, QuinnT.Effects of processing on microstructure and mechanical properties of a titanium alloy (Ti-6Al-4 V) fabricated using electron beam melting (EBM), Part 1: distance from build plate and part size. Mater Sci Eng A. 2013;573:264–270. doi: 10.1016/j.msea.2013.02.064
6.
HrabeN, QuinnT.Effects of processing on microstructure and mechanical properties of a titanium alloy (Ti-6Al-4 V) fabricated using electron beam melting (EBM), Part 2: energy input, orientation, and location. Mater Sci Eng A. 2013;573:271–277. doi: 10.1016/j.msea.2013.02.065
7.
KörnerC.Additive manufacturing of metallic components by selective electron beam melting — a review. Int Mater Rev. 2016;61:361–377. doi: 10.1080/09506608.2016.1176289
8.
MurrLE, EsquivelEV, QuinonesSA, Microstructures and mechanical properties of electron beam-rapid manufactured Ti-6Al-4 V biomedical prototypes compared to wrought Ti-6Al-4 V. Mater Charact. 2009;60:96–105. doi: 10.1016/j.matchar.2008.07.006
9.
XipengT, YihongK, Yu JunT, An experimental and simulation study on build thickness dependent microstructure for electron beam melted Ti–6Al–4 V. J Alloys Compd. 2015;646:303–309. doi: 10.1016/J.JALLCOM.2015.05.178
10.
LuSL, TangHP, NingYP, Microstructure and mechanical properties of long Ti-6Al-4 V rods additively manufactured by selective electron beam melting out of a deep powder bed and the effect of subsequent hot isostatic pressing. Metall Mater Trans A. 2015;46:3824–3834. doi: 10.1007/s11661-015-2976-3
11.
TanX, KokY, TanYJ, Graded microstructure and mechanical properties of additive manufactured Ti-6Al-4 V via electron beam melting. Acta Mater. 2015;97:1–16. doi: 10.1016/j.actamat.2015.06.036
12.
SharmaH, ParfittD, SyedAK, A critical evaluation of the microstructural gradient along the build direction in electron beam melted Ti-6Al-4 V alloy. Mater Sci Eng A. 2019;744:182–194. doi: 10.1016/J.MSEA.2018.12.016
13.
FacchiniL, MagaliniE, RobottiP, Microstructure and mechanical properties of Ti-6Al-4 V produced by electron beam melting of pre-alloyed powders. Rapid Prototyp J. 2009;15:171–178. doi:10.1108/13552540910960262.
14.
KoikeM, MartinezK, GuoL, Evaluation of titanium alloy fabricated using electron beam melting system for dental applications. J Mater Process Technol. 2011;211:1400–1408. doi: 10.1016/j.jmatprotec.2011.03.013
15.
ZhaiY, GalarragaH, LadosDA.Microstructure evolution, tensile properties, and fatigue damage mechanisms in Ti-6Al-4 V alloys fabricated by two additive manufacturing techniques. Procedia Eng. 2015;114:658–666. doi: 10.1016/j.proeng.2015.08.007
16.
de FormanoirC, MichotteS, RigoO, Electron beam melted Ti-6Al-4V: microstructure, texture and mechanical behavior of the as-built and heat-treated material. Mater Sci Eng A. 2016;652:105–119. doi: 10.1016/j.msea.2015.11.052
17.
MohammadhosseiniA, FraserD, MasoodSH, Microstructure and mechanical properties of Ti–6Al–4 V manufactured by electron beam melting process. Mater Res Innov. 2013;17:s106–s112. doi: 10.1179/1432891713Z.000000000302
18.
GongH, GuH, ZengK, Melt pool characterization for selective laser melting of Ti-6Al-4 V pre-alloyed powder. 25th Annu. Int. Solid Free. Fabr. Symp., 2014, p. 256–67.
19.
GongH, RafiK, GuH, Analysis of defect generation in Ti-6Al-4 V parts made using powder bed fusion additive manufacturing processes. Addit Manuf. 2014;1-4:87–98. doi: 10.1016/j.addma.2014.08.002
20.
Tammas-WilliamsS, WithersPJ, ToddI, Porosity regrowth during heat treatment of hot isostatically pressed additively manufactured titanium components. Scr Mater. 2016;122:72–76. doi: 10.1016/j.scriptamat.2016.05.002
21.
LeeE, BanerjeeR, KarS, Selection of α variants during microstructural evolution in α/β titanium alloys. Philos Mag. 2007;87:3615–3627. doi: 10.1080/14786430701373672
22.
DillamoreIL, RobertsWT.Preferred orientation in wrought and annealed metals. Metall Rev. 1965;10:271–380. doi:10.1179/mtlr.1965.10.1.271.
23.
LadaniL.Local and global mechanical behavior and microstructure of Ti6Al4 V parts built using electron beam melting technology. Metall Mater Trans A. 2015;46(9):3835–3841. doi: 10.1007/s11661-015-2965-6
24.
HrabeN, Gnaupel-HeroldT, QuinnT.Fatigue properties of a titanium alloy (Ti-6Al-4 V) fabricated via electron beam melting (EBM): Effects of internal defects and residual stress. Int J Fatigue. 2017;94:202–210. doi: 10.1016/j.ijfatigue.2016.04.022
25.
GreitemeierD, PalmF, SyassenF, Fatigue performance of additive manufactured TiAl6V4 using electron and laser beam melting. Int J Fatigue. 2017;94:211–217. doi: 10.1016/j.ijfatigue.2016.05.001
26.
ArmstrongR, CoddI, DouthwaiteRM, The plastic deformation of polycrystalline aggregates. Philos Mag A J Theor Exp Appl Phys. 1962;7:45–58. doi: 10.1080/14786436208201857
27.
JungJY, ParkJK, ChunCH, Hall—petch relation in two-phase TiAl alloys. Mater Sci Eng A. 1996;220:185–190. doi: 10.1016/S0921-5093(96)10446-9
