Copper matrix composites containing different volume fractions of B4C particles (0–15%) were first fabricated by spark plasma sintering followed by hot rolling in atmospheric environments, then their microstructures, phase compositions, mechanical properties and sintering mechanism were investigated. It was found that B4C particles distributed relatively homogeneously in the copper matrix. Reaction products of CuC8 and B were observed and identified in the composite. Under increasing B4C particle content, the ultimate tensile, yield strength and elongation to fracture of the composites decreased. Failure mode of composites included: (1) the interfacial debonding and (2) the cleavage fracture of copper. Moreover, micro-discharge between the adjacent particles occurred, and its led to local high temperature at the interface.
ParkJJ, HongSM, LeeMK, Enhancement in the microstructure and neutron shielding efficiency of sandwich type of 6061Al-B4C composite material via hot isostatic pressing. Nucl Eng Des. 2015;282:1–7. doi: 10.1016/j.nucengdes.2014.10.020
2.
LiYZ, WangQZ, WangWG, Effect of interfacial reaction on age-hardening ability of B4C/6061Al composites. Mater Sci Eng A. 2015;620:445–453. doi: 10.1016/j.msea.2014.10.025
3.
XuZG, JiangLT, ZhangQ, The design of a novel neutron shielding B4C/Al composite containing Gd. Mater Des2016;11:375–381. doi: 10.1016/j.matdes.2016.07.140
4.
KianiMA, AhmadiSJ, OutokeshM.Preparation and characteristics of epoxy/clay/B4C nanocomposite at high concentration of boron carbide for neutron shielding application. Radiat Phys Chem. 2017;141:223–228. doi: 10.1016/j.radphyschem.2017.07.013
5.
HariprasadT, VaratharajanK, RaviS.Wear characteristics of B4C and Al2O3 reinforced with Al 5083 metal matrix based hybrid composite. Procedia Eng. 2014;97:925–929. doi: 10.1016/j.proeng.2014.12.368
6.
BastürkM, ArztmannJ, JerlichW, Analysis of neutron attenuation in boron-alloyed stainless steel with neutron radiography and JEN-3 gauge. J Nucl Mater. 2005;341:189–200. doi: 10.1016/j.jnucmat.2005.02.003
7.
AbenojarJ, VelascoF, MotaJM, Preparation of Fe/B powders by mechanical alloying. J Solid State Chem. 2004;177:382–388. doi: 10.1016/j.jssc.2003.01.001
8.
SuiYD, ZhouMJ, JiangYH.Characterization of interfacial layer of ZTA ceramic particles reinforced iron matrix composites. J Alloys Compd. 2018;741:1169–1174. doi: 10.1016/j.jallcom.2018.01.199
9.
WuCL, ZhangS, ZhangCH, Formation mechanism and phase evolution of in situ synthesizing TiC-reinforced 316L stainless steel matrix composites by laser melting deposition. Mater Lett. 2018;217:304–307. doi: 10.1016/j.matlet.2018.01.097
10.
EskandariH, TaheriR.A novel technique for development of aluminum alloy matrix/TiB2/Al2O3 hybrid surface nanocomposite by friction stir processing. Proc Mater Sci. 2015;11:503–508. doi: 10.1016/j.mspro.2015.11.080
11.
SuleR, OlubambiPA, SigalasI.Effect of SPS consolidation parameters on submicron Cu and Cu-CNT composites for thermal management. Powder Technol. 2014;258:198–205. doi: 10.1016/j.powtec.2014.03.034
12.
DouYH, LiuY, LiuYB.Friction and wear behaviors of B4C/6061Al composite. Mater Des. 2014;60:669–677. doi: 10.1016/j.matdes.2014.04.016
13.
ZhangP, LiYL, WangWX.The design, fabrication and properties of B4C/Al neutron absorbers. J Nucl Mater. 2013;437:350–358. doi: 10.1016/j.jnucmat.2013.02.050
14.
VintilaR, CharestA, DrewRAL.Synthesis and consolidation via spark plasma sintering of nanostructured Al-5356/B4C composite. Mater Sci Eng A. 2011;528:4395–4407. doi: 10.1016/j.msea.2011.02.079
15.
MonazzahAH, PouraliakbarH, BagheriR, Al-Mg-Si/SiC laminated composites: fabrication, architectural characteristics, toughness, damage tolerance, fracture mechanisms. Composites Part B. 2017;125:49–70. doi: 10.1016/j.compositesb.2017.05.055
16.
MonazzahAH, PouraliakbarH, JandaghiMR, Influence of interfacial adhesion on the damage tolerance of Al6061/SiCp laminated composites. Ceram Int. 2017;43:2632–2643. doi: 10.1016/j.ceramint.2016.11.074
17.
PouraliakbarH, NazariA, FataeiP, Predicting charpy impact energy of Al6061/SiCp laminated nancomposites in crack divider and crack arrester forms. Ceram Int. 2013;39:6099–6106. doi: 10.1016/j.ceramint.2013.01.027
18.
WangB, ZhaoS, OjimaF, Pulse electric current sintering of 3D interpenetrating SiC/Al composites. Ceram Int. 2017;43:2867–2870. doi: 10.1016/j.ceramint.2016.10.202
19.
PouraliakbarH, JandaghiMR, KhalajG.Constrained groove pressing and subsequent annealing of Al-Mn-Si alloy: microstructure evolution, crystallographic transformation, mechanical properties, electrical conductivity and corrosion resistance. Mater Des. 2017;124:34–46. doi: 10.1016/j.matdes.2017.03.053
20.
PouraliakbarH, FiroozS, JandaghiMR, Combined effect of heat treatment and rolling on pre-strained and SPDed aluminum sheet. Mater Sci Eng A. 2014;612:371–379. doi: 10.1016/j.msea.2014.06.044
21.
El-SabbaghA, SolimanM, TahaM, Hot rolling behaviour of stir-cast Al6061 and Al 6082 alloys-SiC fine particulates reinforced composites. J Mater Process Tech. 2012;212:497–508. doi: 10.1016/j.jmatprotec.2011.10.016
22.
KhorramiMS, MostafaeiMA, PouraliakbarH, Study on microstructure and mechanical characteristics of low-carbon steel and ferritic stainless steel joints. Mater Sci Eng A. 2014;608:35–45. doi: 10.1016/j.msea.2014.04.065
23.
SongX, LiuX, ZhangJ.Neck formation and self-adjusting mechanism of neck growth of conducting powders in spark plasma sintering. J Am Ceram Soc. 2006;89:494–500. doi: 10.1111/j.1551-2916.2005.00777.x
