This study examined the effects of a pulsed magnetic field (PMF) on the solidified microstructure and properties of A357 aluminium alloy. Results showed that the solidified microstructure of the alloy treated by a PMF was refined. The treated alloy in the T6 state had superior mechanical properties, with the ultimate tensile strength, yield strength and elongation increasing by 48 MPa (18.5%), 46 MPa (16.4%) and 4.8% (142%), respectively, when compared with the untreated alloy. When testing at room temperature, with a strain amplitude of 1 × 10−4 and at a frequency of 1 Hz, the damping capacity value was 14.2 × 10−3 for the alloy subjected to a PMF treatment, which increased by nearly 170% when compared with the untreated alloy.
WangQG.Plastic deformation behavior of aluminum casting alloys A356/357. Metall Mater Trans A. 2004;35:2707–2718. doi: 10.1007/s11661-004-0216-3
2.
ChenZW, LeiYM, ZhangHF.Structure and properties of nanostructured A357 alloy produced by melt spinning compared with direct chill ingot. J Alloys Compd. 2011;509:7473–7477. doi: 10.1016/j.jallcom.2011.04.082
3.
YangCY, LeeSL, LeeCK, Effects of Be and Fe on the mechanical and corrosion behaviors of A357 alloys. Mater Chem Phys.2005;93:412–419. doi: 10.1016/j.matchemphys.2005.03.029
4.
LiPT, MaXG, LiYG, Effects of trace C addition on the microstructure and refining efficiency of Al-Ti-B master alloy. J Alloys Compd.2010;503:286–290. doi: 10.1016/j.jallcom.2010.04.251
5.
KoriSA, MurtyBS, ChakrabortyM.Development of an efficient grain refiner for Al-7Si alloy and its modification with strontium. Mater Sci Eng A. 2000;283:94–104. doi: 10.1016/S0921-5093(99)00794-7
6.
DahleAK, NogitaK, McDonaldSD, Eutectic modification and microstructure development in Al-Si alloys. Mater Sci Eng A.2005;413-414:243–248. doi: 10.1016/j.msea.2005.09.055
7.
Asensio-LozanoJ, Suarez-PeñaB.Effect of the addition of refiners and/or modifiers on the microstructure of die cast Al-12Si alloys. Scr Mater. 2006;54:943–947. doi: 10.1016/j.scriptamat.2005.10.067
8.
TrivediR, KurzW.Dendritic growth. Int Mater Rev. 1994;39:49–74. doi: 10.1179/imr.1994.39.2.49
9.
YuSR, FengHK, LiYL.A novel method for preparing Al matrix surface composites. J Alloys Compd. 2008;457:404–407. doi: 10.1016/j.jallcom.2007.02.125
10.
YuJB, RenZM, RenWL, Effects of electromagnetic vibration on the structure and mechanical properties of Al-6%Si alloy during directional solidification. Acta Metall Sin.2009;22:35–39. doi: 10.1016/S1006-7191(08)60068-X
11.
VivèsC.Crystallization of aluminum alloys in the presence of vertical electromagnetic force fields. J Cryst Growth. 1997;173:541–549. doi: 10.1016/S0022-0248(96)01051-2
12.
VivèsC.Effects of electromagnetic vibrations on the microstructure of continuously cast aluminium alloys. Mater Sci Eng A. 1993;173:169–172. doi: 10.1016/0921-5093(93)90209-W
13.
BanCY, CuiJZ, BaQX, The influence of pulsed magnetic field on microstructures and macro-segregation in 2124 Al alloy. Acta Metall Sin.2002;15:380–384.
14.
GaoYL, LiQS, GongYY, Comparative study on structural transformation of low-melting pure Al and high-melting stainless steel under external pulsed magnetic field. Mater Lett.2007;61:4011–4014. doi: 10.1016/j.matlet.2007.01.007
15.
WangB, YangYS, ZhouJX, Microstructure refinement of AZ91D alloy solidified with pulsed magnetic field. Trans Nonferrous Met Soc China.2008;18:536–540. doi: 10.1016/S1003-6326(08)60094-1
16.
WangB, YangYS, MaXP, Simulation of electromagnetic-flow fields in Mg melt under pulsed magnetic field. Trans Nonferrous Met Soc China.2010;20:283–288. doi: 10.1016/S1003-6326(09)60135-7
17.
WangB, YangYS, SunML.Microstructure refinement of AZ31 alloy solidified with pulsed magnetic field. Trans Nonferrous Met Soc China. 2010;20:1685–1690. doi: 10.1016/S1003-6326(09)60358-7
18.
ZhangL.Effect of pulsed magnetic field on microstructure and mechanical properties of eutectic Al–Si alloy. Metall Mater Trans B. 2013;44:390–395. doi: 10.1007/s11663-012-9778-4
19.
ZhangL, ZhouQ.Effect of low voltage pulsed magnetic field on microstructure and wear behaviour of eutectic Al-Si alloys. Mater Sci Technol. 2012;28:1527–1530. doi: 10.1179/1743284712Y.0000000072
20.
LiYJ, TaoWZ, YangYS.Grain refinement of Al-Cu alloy in low voltage pulsed magnetic field. J Mater Process Technol. 2012;212:903–909. doi: 10.1016/j.jmatprotec.2011.11.018
21.
FuJW, YangYS.Microstructure and mechanical properties of Mg-Al-Zn alloy under a low-voltage pulsed magnetic field. Mater Lett. 2012;67:252–255. doi: 10.1016/j.matlet.2011.09.021
22.
ZhangL, LiW, YaoJP, Effects of pulsed magnetic field on microstructures and morphology of the primary phase in semisolid A356 Al slurry. Mater Lett. 2012;66:190–192. doi: 10.1016/j.matlet.2011.08.001
23.
MulyukovRR, AkhmadeevNA, ValievRZ, Strain amplitude dependence of internal friction and strength of submicrometre-grained copper. Mat Sci Eng A. 1993;171:143–149. doi: 10.1016/0921-5093(93)90400-9
24.
SchallerR.Metal matrix composites, a smart choice for high damping materials. J Alloys Compd. 2003;355:131–135. doi: 10.1016/S0925-8388(03)00239-1
25.
GranatoAV, LückeK.Theory of mechanical damping due to dislocations. J Appl Phys. 1956;27:583–593. doi: 10.1063/1.1722436
26.
GranatoAV, LückeK.Application of dislocation theory to internal friction phenomena at high frequencies. J Appl Phys. 1956;27:789–805. doi: 10.1063/1.1722485
27.
KêTS.On the physical models of the cold-work (Snoek-Köster) internal-friction peaks in BCC metals. Scr Metall. 1982;16:225–232. doi: 10.1016/0036-9748(82)90341-6
