The heterogeneities in tensile properties, microstructure, solute concentrations and defects levels were studied for the castings with different thicknesses made by high pressure die cast Al–Mg–Si alloys. For the local mechanical properties, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, ultimate tensile strength and elongation. The microstructural heterogeneity was characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic α-Al phase estimated using the Jackson–Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.
This paper is part of a thematic issue on Light Alloys.
VinarcikEJ.High integrity die casting processes. New York: Wiley; 2003.
3.
MacLeanHL, LaveLB.Evaluating automobile fuel/propulsion system technologies. Prog Energy Combust Sci. 2003;29:1–69. doi: 10.1016/S0360-1285(02)00032-1
4.
JiS, WatsonD, FanZ, Development of a super ductile die-cast Al–Mg–Si alloy. Mater Sci Eng A. 2012;556:824–833. doi: 10.1016/j.msea.2012.07.074
5.
OtarawannaS, GourlayCM, LaukliHI, Microstructure formation in AlSi4MgMn and AlMg5Si2Mn high-pressure die castings. Metall Mater Trans A. 2009;40:1645–1659. doi: 10.1007/s11661-009-9841-1
6.
BaroneMR, CaulkDA.Analysis of liquid metal flow in die casting. Int J Eng Sci. 2000;38:1279–1302. doi: 10.1016/S0020-7225(99)00082-8
7.
DahleAK, St JohnDH.Rheological behaviour of the mushy zone and its effect on the formation of casting defects during solidification. Acta Mater. 1998;47:31–41. doi: 10.1016/S1359-6454(98)00342-5
8.
Cepeda-JiménezCM, Orozco-CaballeroA, García-InfantaJM, Assessment of homogeneity of the shear-strain pattern in Al–7 wt%Si casting alloy processed by high-pressure torsion. Mater Sci Eng A. 2014;597:102–110. doi: 10.1016/j.msea.2013.12.072
9.
OtarawannaS, GourlayCM, LaukliHI, The thickness of defect bands in high-pressure die castings. Mater Charact. 2009;60:1432–1441. doi: 10.1016/j.matchar.2009.06.016
10.
YangKV, EastonMA, CáceresCH.The development of the skin in HPDC Mg–Al alloys. Mater Sci Eng A. 2013;580:191–195. doi: 10.1016/j.msea.2013.05.017
11.
KimuraR, HatayamaH, ShinozakiK, Effect of grain refiner and grain size on the susceptibility of Al–Mg die casting alloy to cracking during solidification. J Mater Process Technol. 2009;209:210–219. doi: 10.1016/j.jmatprotec.2008.01.053
12.
HamasaiidA, DarguschMS, DavidsonCJ, Effect of mould coating materials and thickness on heat transfer in permanent mould casting of aluminium alloys. Metall Mater Trans A. 2007;38:1303–1316. doi: 10.1007/s11661-007-9145-2
13.
YangKV, CáceresCH, NagasekharAV, The skin effect and the yielding behaviour of cold chamber high pressure die cast Mg–Al alloys. Mater Sci Eng A. 2012;542:49–55. doi: 10.1016/j.msea.2012.02.029
14.
SeoPK, KimDU, KangCG.Effects of die shape and injection conditions proposed with numerical integration design on liquid segregation and mechanical properties in semi-solid die casting process. J Mater Process Technol. 2006;176:45–54. doi: 10.1016/j.jmatprotec.2006.02.017
15.
ClearyPW, HaJ, PrakashM, Short shots and industrial case studies: understanding fluid flow and solidification in high pressure die casting. Appl Math Model. 2010;34:2018–2033. doi: 10.1016/j.apm.2009.10.015
16.
SuiY, WangQ, YeB, Effect of solidification sequence on the microstructure and mechanical properties of die-cast Al–11Si–2Cu–Fe alloy. J Alloys Compd. 2015;649:679–686. doi: 10.1016/j.jallcom.2015.07.187
17.
JiS, WangY, WatsonD, Microstructural evolution and solidification behaviour of Al–Mg–Si alloy in high-pressure die casting. Metall Mater Trans A. 2013;44:3185–3197. doi: 10.1007/s11661-013-1663-5
18.
ChenZW.Skin solidification during high pressure die casting of Al–11Si–2Cu–1Fe alloy. Mater Sci Eng A. 2003;348:145–153. doi: 10.1016/S0921-5093(02)00747-5
19.
TaylorJA.Iron-containing intermetallic phases in Al–Si based casting alloys. Procedia Mater Sci. 2012;1:19–33. doi: 10.1016/j.mspro.2012.06.004
20.
JiS, YangW, GaoF, Effect of iron on the microstructure and mechanical property of Al–Mg–Si–Mn and Al–Mg–Si diecast alloys. Mater Sci Eng A. 2013;564:130–139. doi: 10.1016/j.msea.2012.11.095
21.
FerraroS, FabriziA, TimelliG.Evolution of sludge particles in secondary die-cast aluminum alloys as function of Fe, Mn and Cr contents. Mater Chem Phys. 2015;153:168–179. doi: 10.1016/j.matchemphys.2014.12.050
22.
GramegnaN, LoizagaI, BerrocalS, Advances in production management systems, competitive manufacturing for innovative products and services. IFIP Adv Inf Commun Technol. 2013;397:502–509. doi: 10.1007/978-3-642-40352-1_63
23.
TimelliG, BonolloF.Quality mapping of aluminium alloy die castings. Metal Sci Technol. 2008;26–1:2–8.
24.
LumleyRN.Progress on the heat treatment of high pressure die castings. In: Fundamentals of aluminium metallurgy. Cambridge: Woodhead Publishing; 2011. p. 262–303.
25.
ShaG, MöllerH, StumpfWE, Solute nanostructures and their strengthening effects in Al–7Si–0.6Mg alloy F357. Acta Mater. 2012;60:692–701. doi: 10.1016/j.actamat.2011.10.029
26.
NottPR, BradyJF.Pressure-driven flow of suspensions, simulation and theory. J Fluid Mech. 1994;275:157–199. doi: 10.1017/S0022112094002326
27.
JacksonKA, HuntJD.Lamellar and rod eutectic growth. Trans Metall Soc AIME. 1966;236:1129–1142.
28.
GrugelR, KurzW.Growth of interdendritic eutectic in directionally solidified Al–Si alloys. Metall Mater Trans A. 1987;18:1137–1142. doi: 10.1007/BF02668564
29.
BöyükU, EnginS, MaraşlıN.Microstructural characterization of unidirectional solidified eutectic Al–Si–Ni alloy. Mater Charact. 2011;62:844–851. doi: 10.1016/j.matchar.2011.05.010
30.
KayaH, CadirliE, GündüzM.Eutectic growth of unidirectionally solidified bismuth–cadmium alloy. J Mater Process Technol. 2007;183:310–320. doi: 10.1016/j.jmatprotec.2006.10.022
31.
WhelanEP, HaworthCW.The morphology of some binary eutectic alloys. J Aust Inst Met. 1967;12:77–126.
32.
TrivediR, MasonJT, VerhoevenJD, Eutectic spacing selection in lead-based alloy systems. Metall Mater Trans. 1991;22:2523–2533. doi: 10.1007/BF02665018
33.
MooreA, ElliottR.Solidification of Metals: Proceedings of the Conference on Solidification of Metals. Brighton, UK: London Iron and Steel Institute. 1967. p. 167–174.
34.
CadirliE, KayaH, GunduzM.Effect of growth rates and temperature gradients on the lamellar spacing and the undercooling in the directionally solidified Pb–Cd eutectic alloy. Mater Res Bull. 2003;38:1457–1476. doi: 10.1016/S0025-5408(03)00169-7
35.
CadirliE, UlgenA, GunduzM.Directional solidification of the aluminium-copper eutectic alloy. Mater Trans JIM. 1999;40:989–996. doi: 10.2320/matertrans1989.40.989
36.
KoçakY, EnginS, BöyükU, The influence of the growth rate on the eutectic spacings, undercoolings and microhardness of directional solidified bismuth-lead eutectic alloy. Curr Appl Phys. 2013;13:587–593. doi: 10.1016/j.cap.2012.10.005
37.
SchwarzDM, ArnoldCB, AzizMJ, Dendritic growth velocity and diffusive speed in solidification of undercooled dilute Ni–Zr melts. Mater Sci Eng A. 1997;226–228:420–424. doi: 10.1016/S0921-5093(96)10656-0
