Lap joints of friction stir welding between aluminium and stainless steel sheets were conducted using a welding tool with a cutting pin. The atomic diffusion of Fe–Al system during the severe plastic deformation was investigated. The interfacial microstructure and metallurgical reaction was analysed. The metallurgical reaction layers were identified as a compounds containing a phase of Al3Fe, partial solid solution of Fe and Al, and amorphous with a thickness of 0.9–3.3 μm which depending on the process parameters. The interdiffusion coefficient between Al and Fe atoms is about 4 orders of magnitude compared with that under thermal equilibrium state. The nanocrystalline and partial amorphous were formed near the interface which may caused by the enhanced atomic diffusion.
DebRoyT, BhadeshiaHKDH. Friction stir welding of dissimilar alloys – a perspective. Sci Technol Weld Join. 2010;15:266–270. doi: 10.1179/174329310X12726496072400
2.
ChenYC, GholiniaA, PrangnellPB. Interface structure and bonding in abrasion circle friction stir spot welding: a novel approach for rapid welding aluminium alloy to steel automotive sheet. Mater Chem Phys. 2012;134:459–463. doi: 10.1016/j.matchemphys.2012.03.017
3.
MahtoRP, BhojeR, PalSK, A study on mechanical properties in friction stir lap welding of AA 6061-T6 and AISI 304. Mater Sci Eng A. 2016;652:136–144. doi: 10.1016/j.msea.2015.11.064
4.
KusudaY. Honda develops robotized FSW technology to weld steel and aluminum and applied it to a mass-production vehicle. Ind Robot. 2013;40:208–212. doi: 10.1108/01439911311309889
5.
LiangZ, ChenK, WangX, Effect of tool offset and tool rotational speed on enhancing mechanical property of Al/Mg dissimilar FSW joints. Metall Mater Trans A. 2013;44:3721–3731. doi: 10.1007/s11661-013-1700-4
6.
ZhangJQ, ShenYF, YaoX, Investigation on dissimilar underwater friction stir lap welding of 6061-T6 aluminum alloy to pure copper. Mater Des. 2014;64:74–80. doi: 10.1016/j.matdes.2014.07.036
7.
LiuX, LanS, NiJ. Analysis of process parameters effects on friction stir welding of dissimilar aluminum alloy to advanced high strength steel. Mater Des. 2014;59:50–62. doi: 10.1016/j.matdes.2014.02.003
8.
MishraRS, MaZY. Friction stir welding and processing. Mater Sci Eng R. 2005;50:1–78. doi: 10.1016/j.mser.2005.07.001
9.
ZhaoY, HuangL, ZhaoZ, Effect of travel speed on the microstructure of Al-to-Mg FSW joints. Mater Sci Technol. 2016;32(10):1025–1034. doi: 10.1080/02670836.2015.1110281
10.
ZhangD, ShibayanagiT. Material flow during friction stir spot welding of dissimilar Al2024/Al materials. Mater Sci Technol. 2015;31(9):1077–1087. doi: 10.1179/1743284714Y.0000000674
11.
BirolY, KasmanS. Effect of welding parameters on microstructure and mechanical properties of friction stir welded EN AW 5083 H111 plates. Mater Sci Technol. 2013;29(11):1354–1362. doi: 10.1179/1743284713Y.0000000280
12.
ElrefaeyA, GoudaM, TakahashiM, Characterization of aluminum/steel lap joint by friction stir welding. J Mater Eng Perform. 2005;14:10–17. doi: 10.1361/10599490522310
13.
MovahediM, KokabiAH, Seyed ReihaniSM, Effect of tool travel and rotation speeds on weld zone defects and joint strength of aluminum steel lap joints made by friction stir welding. Sci Technol Weld Join. 2013;17(17):162–167.
14.
KimapongK, WatanabeT. Lap Joint of A5083 aluminum alloy and SS400 steel by friction stir welding. Mater Trans. 2005;46:835–841. doi: 10.2320/matertrans.46.835
15.
WatanabeT, TakayamaH, YanagisawaA. Joining of aluminum alloy to steel by friction stir welding. J Mater Process Technol. 2006;178:342–349. doi: 10.1016/j.jmatprotec.2006.04.117
16.
MovahediM, KokabiAH, ReihaniSMS, Mechanical and microstructural characterization of A1-5083/St-12 lap joints made by friction stir welding. Procedia Eng. 2011;10(7):3297–3303. doi: 10.1016/j.proeng.2011.04.544
17.
BalluffiRW, RuoffAL. On strain-enhanced diffusion in metals: I. point defect models. J Appl Physiol. 1963;34(6):1634–1647. doi: 10.1063/1.1702647
18.
DasN, PabiSK, KulkarniUD, Development of a thermodynamic criterion to predict the alloy compositions for amorphous and nanocrystalline phase formation during mechanical alloying. Defect Diffus Forrum. 2008;279:147–151. doi: 10.4028/www.scientific.net/DDF.279.147
19.
LiMY, JiHJ, WangCQ, Interdiffusion of Al–Ni system enhanced by ultrasonic vibration at ambient temperature. Ultrasonics. 2006;45(14):61–65. doi: 10.1016/j.ultras.2006.06.058
20.
QianJW, LiJL, XiongJT, In situ synthesizing Al3Ni for fabrication of intermetallic-reinforced aluminum alloy composites by friction stir processing. Mater Sci Eng A. 2012;550:279–285. doi: 10.1016/j.msea.2012.04.070
21.
KuksinAY, YanilkinAV. Dislocation nucleation and motion in metals and alloys at high-rate deformation: molecular dynamic simulation. Mech Solids. 2015;50(1):44–51. doi: 10.3103/S0025654415010057
22.
SchwenD, WangM. Compositional patterning in immiscible alloys subjected to severe plastic deformation. Scr Mater. 2013;28(19):2687–2693.
23.
RamachandranKK, MuruganN, Shashi KumarS. Effect of tool axis offset and geometry of tool pin profile on the characteristics of friction stir welded dissimilar joints of aluminum alloy AA5052 and HSLA steel. Mater Sci Eng A. 2015;639:219–233. doi: 10.1016/j.msea.2015.04.089
24.
KumarK, KailasSV. The role of friction stir welding tool on material flow and weld formation. Mater Sci Eng A. 2008;485:367–374. doi: 10.1016/j.msea.2007.08.013
TangW, GuoX, McClureJC, Heat input and temperature distribution in friction stir welding. J Mater Process Manuf Sci. 1998;7(2):163–172. doi: 10.1106/55TF-PF2G-JBH2-1Q2B
27.
HashimotoT, JyoganS, NakataK, In: Proceedings of the First International Symposium on Friction Stir Welding, June 14–16; Thousand Oaks (CA), USA; 1999 .
28.
JainR, PalSK, SinghSB. A study on the variation of forces and temperature in a friction stir welding process: a finite element approach. J Manuf Process. 2016;23:278–286. doi: 10.1016/j.jmapro.2016.04.008
29.
XiongJT, LiJL.QianJW, High strength lap joint of aluminium and stainless steels fabricated by friction stir welding with cutting pin. Sci Technol Weld Join. 2012;17:196–201. doi: 10.1179/1362171811Y.0000000093
30.
NeumannG, TuijnC.Self-diffusion and impurity diffusion in pure metals: handbook of experimental data. Amsterdam: Elsevier; 2009; p. 103–310.
31.
XuY, ChenJ. Atomistic potentials based energy flux integral criterion for dynamic adiabatic shear banding. J Mech Phys Solids. 2015;75:45–57. doi: 10.1016/j.jmps.2014.11.003
32.
BellonP, AverbackRS, OdunugaS, Crossover from superdiffusive to diffusive mixing in plastically deformed solids. Phys Rev Lett. 2007;99(11):110602: 1–4. doi: 10.1103/PhysRevLett.99.110602
